Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › 2017.08–2020.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0325854 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) C

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  U0265  Lost Communication with Parking Assist Monitor Module  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
U0265 Lost Communication with Parking Assist Monitor Module There is no communication from the rear television camera assembly.
·

Rear television camera assembly CAN branch wire or connector

·

Power source circuit of rear television camera assembly

·

Rear television camera assembly ground circuit

·

Rear television camera assembly


Main body ECU (multiplex network body ECU)

WIRING DIAGRAM

C382790E02
0.229,1.625 0.844,1.823 0.615,0.198 10 false G288 0.219,1.792 2.177,2.073 1.958,0.281 10 false No. 4 CAN Junction Connector 1.719,1.281 2.333,1.479 0.615,0.198 10 false 16 1.781,0.781 2.396,0.979 0.615,0.198 10 false 5 5.656,0.906 6.271,1.104 0.615,0.198 10 false CANH 5.667,1.365 6.281,1.563 0.615,0.198 10 false CANL 5.427,1.26 6.042,1.458 0.615,0.198 10 false 1 5.438,0.781 6.052,0.979 0.615,0.198 10 false 4 5.646,2.938 6.26,3.135 0.615,0.198 10 false CB+ 5.667,3.51 6.281,3.708 0.615,0.198 10 false CGND 5.417,3.396 6.031,3.594 0.615,0.198 10 false 5 5.427,2.802 6.042,3 0.615,0.198 10 false 6 5.365,3.958 6.385,4.156 1.021,0.198 10 false X10*3, v3*4 5.333,4.104 6.865,4.531 1.531,0.427 10 false Rear Television Camera Assembly 0.229,3.813 1.229,4.063 1,0.25 10 false H50*1, H55*2 0.208,3.969 3.573,4.469 3.365,0.5 10 false Radio and Display Receiver Assembly (EMVN ECU)*1, Navigation Receiver Assembly (EMVN ECU)*2 1.198,3.521 1.813,3.719 0.615,0.198 10 false CGND 1.302,2.948 1.917,3.146 0.615,0.198 10 false CA+ 1.698,2.813 2.313,3.01 0.615,0.198 10 false 11 1.729,3.354 2.344,3.552 0.615,0.198 10 false 23 0.146,4.875 2.615,5.125 2.469,0.25 10 false *1: w/ Audio and Visual System 0.146,5.229 2.615,5.479 2.469,0.25 10 false *2: w/ Navigation System 2.281,4.885 3.917,5.125 1.635,0.24 10 false *3: w/o Tire Carrier 2.25,5.25 3.885,5.49 1.635,0.24 10 false *4: w/ Tire Carrier

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

DTC check procedure: Turn the ignition switch to ON, wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Check for DTCs.

HINT:

If DTC U1002 is output from the gateway of the network gateway ECU, this indicates a sub bus 2 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in sub bus 2.



Result:
Result Proceed to
U1002 is not output from network gateway ECU A
U1002 is output from network gateway ECU B



A

2.CHECK FOR OPEN IN CAN BUS WIRE (REAR TELEVISION CAMERA ASSEMBLY BRANCH WIRE)

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK FOR OPEN IN CAN BUS WIRE (REAR TELEVISION CAMERA ASSEMBLY BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C346954C25
1.5,0.083 1.906,0.292 0.406,0.208 1.5,0.323 1.906,0.531 0.406,0.208 0.917,1.844 1.083,1.844 1.083,1.844 1.5,1.354 true 0.792,0.583 0.938,0.583 0.938,0.583 1.479,1.094 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 1.583,0.115 1.896,0.271 0.313,0.156 10 false X10 0.448,1.75 0.938,1.917 0.49,0.167 10 false CANH 0.406,0.5 0.896,0.667 0.49,0.167 10 false CANL 1.625,0.354 1.938,0.51 0.313,0.156 10 false v3 1.938,0.115 2.25,0.271 0.313,0.156 10 false *A 1.938,0.344 2.25,0.5 0.313,0.156 10 false *B
*A w/o Tire Carrier
*B w/ Tire Carrier
*a Front view of wire harness connector
(to Rear Television Camera Assembly)


Disconnect the rear television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Tire Carrier
Tester Connection Condition Specified Condition
X10-4 (CANH) - X10-1 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω

w/ Tire Carrier
Tester Connection Condition Specified Condition
v3-4 (CANH) - v3-1 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C346954C26
1.5,0.083 1.906,0.292 0.406,0.208 1.5,0.323 1.906,0.531 0.406,0.208 1.188,1.927 1.354,1.927 1.354,1.927 1.708,1.417 true 2.25,1.917 2.083,1.917 2.083,1.917 1.917,1.396 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 1.583,0.115 1.896,0.271 0.313,0.156 10 false X10 0.771,1.854 1.26,2.021 0.49,0.167 10 false CGND 2.302,1.823 2.698,2.021 0.396,0.198 10 false CB+ 1.625,0.354 1.938,0.51 0.313,0.156 10 false v3 1.938,0.115 2.25,0.271 0.313,0.156 10 false *A 1.938,0.344 2.25,0.5 0.313,0.156 10 false *B
*A w/o Tire Carrier
*B w/ Tire Carrier
*a Front view of wire harness connector
(to Rear Television Camera Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Tire Carrier
Tester Connection Condition Specified Condition
X10-5 (CGND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω

w/ Tire Carrier
Tester Connection Condition Specified Condition
v3-5 (CGND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/o Tire Carrier
Tester Connection Switch Condition Specified Condition
X10-6 (CB+) - Body ground Ignition switch ON 5.5 to 7.05 V
Ignition switch off Below 1 V

w/ Tire Carrier
Tester Connection Switch Condition Specified Condition
v3-6 (CB+) - Body ground Ignition switch ON 5.5 to 7.05 V
Ignition switch off Below 1 V



Result:
Result Proceed to
OK A
NG (w/ Audio and Visual System) B
NG (w/ Navigation System) C



A

B

4.CHECK HARNESS AND CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY [EMVN ECU])

C

5.CHECK HARNESS AND CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY [EMVN ECU])
4.CHECK HARNESS AND CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY [EMVN ECU])
a.

Disconnect the H50 radio and display receiver assembly (EMVN ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Tire Carrier
Tester Connection Condition Specified Condition
X10-5 (CGND) - H50-23 (CGND) Always Below 1 Ω
X10-6 (CB+) - H50-11 (CA+)
X10-5 (CGND) - X10-6 (CB+) Always 10 kΩ or higher

w/ Tire Carrier
Tester Connection Condition Specified Condition
v3-5 (CGND) - H50-23 (CGND) Always Below 1 Ω
v3-6 (CB+) - H50-11 (CA+)
v3-5 (CGND) - v3-6 (CB+) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY [EMVN ECU])

5.CHECK HARNESS AND CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY [EMVN ECU])
a.

Disconnect the H55 navigation receiver assembly (EMVN ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Tire Carrier
Tester Connection Condition Specified Condition
X10-5 (CGND) - H55-23 (CGND) Always Below 1 Ω
X10-6 (CB+) - H55-11 (CA+)
X10-5 (CGND) - X10-6 (CB+) Always 10 kΩ or higher

w/ Tire Carrier
Tester Connection Condition Specified Condition
v3-5 (CGND) - H55-23 (CGND) Always Below 1 Ω
v3-6 (CB+) - H55-11 (CA+)
v3-5 (CGND) - v3-6 (CB+) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY [EMVN ECU])