| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from |
|---|---|---|---|---|
| U0200 | Lost Communication with "Door Control Module B" | There is no communication from the outer mirror control ECU assembly RH. | ·
Power source circuit of outer mirror control ECU assembly RH ·
Outer mirror control ECU assembly RH ground circuit ·
Outer mirror control ECU assembly RH CAN branch wire or connector ·
Outer mirror control ECU assembly RH |
Main body ECU (multiplex network body ECU) |
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Inspect the fuses for circuits related to this system before performing the following procedure.
DTC check procedure: Turn the ignition switch to ON, wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.
After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Check for DTCs.
If DTC U1002 is output from the gateway of the main body ECU (multiplex network body ECU), this indicates a sub bus 1 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in sub bus 1.
| Result | Proceed to |
|---|---|
| DTC U1002 is not output from main body ECU (multiplex network body ECU) | A |
| DTC U1002 is output from main body ECU (multiplex network body ECU) | B |
A
B
| *a | Front view of wire harness connector
(to Outer Mirror Control ECU Assembly RH) |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the outer mirror control ECU assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J12-9 (CANP) - J12-8 (CANN) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Outer Mirror Control ECU Assembly RH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J12-7 (GND) - Body ground | Cable disconnected from negative (-) battery terminal | Below 1 Ω |
Reconnect the cable to the negative (-) battery terminal.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J12-5 (SIG) - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V | |
| J12-6 (CPUB) - Body ground | Always | 11 to 14 V |
| J12-14 (BDR) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG