Home › Drivetrain › VF4BM (TRANSFER / 4WD / AWD) › TRANSFER ASSEMBLY › from 2017.08
RM27T0E _52 Drivetrain _053703 VF4BM TRANSFER / 4WD / AWD _0260842 TRANSFER ASSEMBLY G

VF4BM TRANSFER / 4WD / AWD  TRANSFER ASSEMBLY  INSPECTION  


PROCEDURE

Hide 36211 1.INSPECT TRANSFER INPUT SHAFT

a.
F043458

Using a micrometer, measure the outer diameter of the input shaft journal surface.

Minimum diameter:

47.59 mm (1.88 in.)


If the outer diameter is less than the minimum, replace the input shaft.


Hide 2.INSPECT PLANETARY PINION GEAR THRUST CLEARANCE

a.
F043465

Using a feeler gauge, measure the thrust clearance of the planetary pinion gear.

Standard clearance:

0.11 to 0.84 mm (0.00434 to 0.0330 in.)


Maximum clearance:

0.84 mm (0.0330 in.)


If the clearance is more than the maximum, replace the planetary gear.


Hide 3.INSPECT PLANETARY PINION GEAR RADIAL CLEARANCE

a.
F043466

Using a dial indicator, measure the radial clearance of the planetary pinion gear.

Standard clearance:

0.009 to 0.038 mm (0.000355 to 0.00149 in.)


Maximum clearance:

0.038 mm (0.00149 in.)


If the clearance is more than the maximum, replace the planetary gear.


Hide 36231 4.INSPECT TRANSFER OUTPUT SHAFT REAR

a.
F043511E05
3.021,0.292 3.167,0.458 0.146,0.167 10 false A 2.667,0.292 2.813,0.458 0.146,0.167 10 false B 1.833,0.292 1.979,0.458 0.146,0.167 10 false C 1.292,0.292 1.438,0.458 0.146,0.167 10 false D

Using a micrometer, measure the outer diameter of the output shaft rear journal surfaces.

Standard diameter:
Journal A:

27.98 to 27.99 mm (1.1015 to 1.1019 in.)

Journal B:

31.98 to 32.00 mm (1.2591 to 1.2598 in.)

Journal C:

34.98 to 35.00 mm (1.3772 to 1.3779 in.)

Journal D:

36.98 to 37.00 mm (1.4560 to 1.4566 in.)


Minimum diameter:
Journal A:

27.98 mm (1.1015 in.)

Journal B:

31.98 mm (1.2591 in.)

Journal C:

34.98 mm (1.3772 in.)

Journal D:

36.98 mm (1.4560 in.)


If the outer diameter is less than the minimum, replace the rear output shaft.


Hide 36235 5.INSPECT TRANSFER HIGH AND LOW CLUTCH SLEEVE AND NO. 2 TRANSFER GEAR SHIFT FORK CLEARANCE

a.
F043481E07
0.531,1.729 0.833,1.896 0.302,0.167 10 false (A) 2.333,1.729 2.635,1.896 0.302,0.167 10 false (B)

Using a vernier caliper, measure the thickness of the shift fork claw.

Standard thickness (A):

10 mm (0.394 in.)



b.

Using a vernier caliper, measure the width of the groove of the high and low clutch sleeve.

Standard width (B):

10.5 mm (0.413 in.)



c.

Calculate the clearance between the high and low clutch sleeve and shift fork.

Standard clearance (B) - (A):

0.26 to 0.84 mm (0.0103 to 0.0330 in.)


Maximum clearance (B) - (A):

0.84 mm (0.0330 in.)


If the clearance is more than the maximum, replace the high and low clutch sleeve or shift fork.


Hide 36236 6.INSPECT FRONT DRIVE CLUTCH SLEEVE AND CENTER DIFFERENTIAL LOCK FORK SUB-ASSEMBLY CLEARANCE

a.
F043483E05
0.625,1.74 0.948,1.896 0.323,0.156 10 false (A) 2.323,1.74 2.552,1.896 0.229,0.156 10 false (B)

Using a vernier caliper, measure the thickness of the center differential lock fork claw.

Standard thickness (A):

10 mm (0.394 in.)



b.

Using a vernier caliper, measure the width of the groove of the front drive clutch sleeve.

Standard width (B):

10.5 mm (0.413 in.)



c.

Calculate the clearance between the front drive clutch sleeve and differential lock fork.

Standard clearance (B) - (A):

0.26 to 0.84 mm (0.0103 to 0.0330 in.)


Maximum clearance (B) - (A):

0.84 mm (0.0330 in.)


If the clearance is more than the maximum, replace the front drive clutch sleeve or differential lock fork.


Hide 7.INSPECT CENTER DIFFERENTIAL CASE AND TRANSFER HIGH AND LOW CLUTCH SLEEVE

a.
F043493

Check that the splines of the clutch sleeve are not worn.


b.

Install the clutch sleeve to the center differential case and check that the clutch sleeve moves smoothly.


Hide 8.INSPECT CENTER DIFFERENTIAL CASE AND FRONT DRIVE CLUTCH SLEEVE

a.
F044398

Check that the splines of the clutch sleeve are not worn.


b.

Install the clutch sleeve to the center differential case and check that the clutch sleeve moves smoothly.


Hide 36410J 9.INSPECT TRANSFER SHIFT ACTUATOR ASSEMBLY

a.

Inspect the multi mode transfer shift actuator (transfer shift actuator assembly).

i.

Remove the transfer shift actuator assembly

Click hereDrivetrain>VF4BM (TRANSFER / 4WD / AWD)>TRANSFER ASSEMBLY>DISASSEMBLY


ii.

Check the LOCK to FREE switch.

Connect lines via a relay as shown in the illustration, then check that the actuator fork moves from the LOCK to FREE position.

NOTICE:
·

Perform this inspection with the actuator removed from the vehicle. If this inspection is performed with the actuator installed to the vehicle, the actuator will be damaged.

·

When inspecting the actuator, operate it with the lines connected via a relay. If the lines are not connected via a relay and battery voltage is directly applied to the actuator, the actuator will be damaged.



HINT:

When performing the operation described above, use the DEF relay on the main body ECU (instrument panel junction block).


C218269C09
5.563,1.583 5.229,1.583 true 6,2.031 6.5,2.031 true 6,2.438 6.5,2.438 true 6.083,1.583 6.5,1.583 true 5.823,1.5 5.823,1.083 true 2.083,2.844 1.74,2.844 true 2.052,3.396 1.552,2.896 true 0.979,3.375 1.24,2.875 true 0.594,3.385 1.083,2.885 true 0.875,2.823 0.563,2.823 false 1.427,3.052 1.646,3.396 true 1.271,3.042 1.323,3.365 true 2.917,1.333 2.917,1.083 2.917,1.083 2.75,1.083 true 4.771,0.292 4.979,0.438 0.208,0.146 10 false *1 2.583,0.99 2.792,1.135 0.208,0.146 10 false *1 5.115,1.49 5.302,1.667 0.188,0.177 10 false 1 6.531,1.5 6.698,1.698 0.167,0.198 10 false 2 5.781,0.917 5.948,1.083 0.167,0.167 10 false 4 6.542,1.938 6.708,2.125 0.167,0.188 10 false 5 6.542,2.365 6.708,2.521 0.167,0.156 10 false 3 0.521,2.344 0.708,2.5 0.188,0.156 10 false *a 1.99,3.406 2.365,3.563 0.375,0.156 10 false TM1 2.125,2.771 2.469,2.938 0.344,0.167 10 false TM2 0.427,3.406 0.74,3.573 0.313,0.167 10 false TL3 0.177,2.76 0.594,2.927 0.417,0.167 10 false GND1 1.167,3.375 1.531,3.542 0.365,0.167 10 false GND 0.708,1.073 1.021,1.26 0.313,0.188 10 false *b 0.833,3.385 1.167,3.563 0.333,0.177 10 false TL2 1.573,3.396 1.906,3.573 0.333,0.177 10 false CDL
*1 DEF Relay - -
*a Component without harness connected
(Transfer Shift Actuator Assembly)
*b LOCK to FREE


1.

After the LOCK to FREE switch is complete, inspect the center differential lock detection switch and limit switch.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (TL2) - 6 (GND1) After LOCK to FREE switch is complete 0.5 MΩ or higher
5 (TL3) - 6 (GND1) After LOCK to FREE switch is complete Below 12.5 Ω
9 (CDL) - 10 (GND) After LOCK to FREE switch is complete 0.5 MΩ or higher




iii.

Check the FREE to LOCK switch.

Connect lines via a relay as shown in the illustration, then check that the actuator fork moves from the FREE to LOCK position.

C218270C07
5.99,2.031 6.49,2.031 true 6,2.438 6.5,2.438 true 6.083,1.583 6.5,1.583 true 5.833,1.5 5.833,0.917 true 5.563,1.583 5.156,1.583 true 2.115,2.854 1.771,2.854 true 2.073,3.375 1.563,2.875 true 0.969,3.333 1.26,2.875 true 0.667,3.25 1.094,2.875 true 0.917,2.802 0.573,2.802 true 1.458,3.031 1.646,3.385 true 1.271,3.052 1.281,3.313 true 2.917,1.333 2.917,1.083 2.917,1.083 2.75,1.083 true 5.052,0.354 5.24,0.552 0.188,0.198 10 false *1 2.594,1 2.781,1.198 0.188,0.198 10 false *1 5.042,1.5 5.229,1.677 0.188,0.177 10 false 1 6.542,1.5 6.708,1.698 0.167,0.198 10 false 2 5.802,0.74 6.052,0.906 0.25,0.167 10 false 4 6.542,1.948 6.708,2.135 0.167,0.188 10 false 5 6.542,2.354 6.708,2.51 0.167,0.156 10 false 3 0.458,2.146 0.635,2.344 0.177,0.198 10 false *a 1.99,3.406 2.365,3.563 0.375,0.156 10 false TM1 2.167,2.781 2.51,2.948 0.344,0.167 10 false TM2 0.438,3.167 0.75,3.333 0.313,0.167 10 false TL3 0.156,2.75 0.604,2.917 0.448,0.167 10 false GND1 1.146,3.354 1.49,3.521 0.344,0.167 10 false GND 0.854,0.979 1.146,1.167 0.292,0.188 10 false *b 0.792,3.354 1.125,3.531 0.333,0.177 10 false TL2 1.573,3.406 1.906,3.583 0.333,0.177 10 false CDL
*1 DEF Relay - -
*a Component without harness connected
(Transfer Shift Actuator Assembly)
*b FREE to LOCK


1.

After the FREE to LOCK switch is complete, inspect the center differential lock detection switch and limit switch.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (TL2) - 6 (GND1) After FREE to LOCK switch is complete Below 12.5 Ω
5 (TL3) - 6 (GND1) After FREE to LOCK switch is complete 0.5 MΩ or higher
9 (CDL) - 10 (GND) After FREE to LOCK switch is complete Below 12.5 Ω


If the result is not as specified, replace the transfer shift actuator assembly (Click hereDrivetrain>VF4BM (TRANSFER / 4WD / AWD)>TRANSFER ASSEMBLY>DISASSEMBLY)

If the transfer shift actuator assembly is normal, replace the 4 wheel drive control ECU (Click hereDrivetrain>VF4BM (TRANSFER / 4WD / AWD)>4WD CONTROL ECU>REMOVAL)




b.

Inspect the high-low transfer shift actuator (transfer shift actuator assembly).

i.

Remove the transfer shift actuator assembly

Click hereDrivetrain>VF4BM (TRANSFER / 4WD / AWD)>TRANSFER ASSEMBLY>DISASSEMBLY


ii.

Check the HIGH to LOW switch.

Connect lines via a relay as shown in the illustration, then check that the actuator fork moves from the HIGH to LOW position.

NOTICE:
·

Perform this inspection with the actuator removed from the vehicle. If this inspection is performed with the actuator installed to the vehicle, the actuator will be damaged.

·

When inspecting the actuator, operate it with the lines connected via a relay. If the lines are not connected via a relay and battery voltage is directly applied to the actuator, the actuator will be damaged.



HINT:

When performing the operation described above, use the DEF relay on the main body ECU (instrument panel junction block).


C218271C09
5.906,2.375 6.406,2.375 true 5.906,2.792 6.406,2.792 true 6,2 6.417,2 true 5.74,1.844 5.74,1.333 true 5.479,2 5.083,2 true 0.833,2.271 0.49,2.271 true 1.052,2.25 0.531,1.802 true 1.219,2.229 0.948,1.552 true 1.531,2.229 1.635,1.604 true 1.719,2.24 1.948,1.823 true 2.74,1.542 2.906,1.542 2.906,1.542 2.906,1.792 false 4.677,0.563 4.854,0.729 0.177,0.167 10 false *1 2.594,1.458 2.771,1.625 0.177,0.167 10 false *1 4.979,1.917 5.167,2.094 0.188,0.177 10 false 1 6.469,1.927 6.635,2.125 0.167,0.198 10 false 2 5.708,1.125 5.958,1.292 0.25,0.167 10 false 4 6.448,2.302 6.615,2.49 0.167,0.188 10 false 5 6.438,2.719 6.604,2.875 0.167,0.156 10 false 3 0.344,1.229 0.542,1.396 0.198,0.167 10 false *a 1.542,1.417 1.917,1.573 0.375,0.156 10 false HM1 1.875,1.656 2.219,1.823 0.344,0.167 10 false HM2 0.219,2.188 0.531,2.354 0.313,0.167 10 false HL1 0.75,1.365 1.125,1.531 0.375,0.167 10 false GND 0.26,0.604 0.458,0.76 0.198,0.156 10 false *b 0.271,1.667 0.604,1.844 0.333,0.177 10 false HL2
*1 DEF Relay - -
*a Component without harness connected
(Transfer Shift Actuator Assembly)
*b HIGH to LOW


1.

After the HIGH to LOW switch is complete, inspect the limit switch.

Standard Resistance:
Tester Connection Condition Specified Condition
12 (HL1) - 10 (GND) After HIGH to LOW switch is complete Below 12.5 Ω
11 (HL2) - 10 (GND) After HIGH to LOW switch is complete 0.5 MΩ or higher




iii.

Check the HIGH to LOW switch.

Connect lines via a relay as shown in the illustration, then check that the actuator fork moves from the HIGH to LOW position.

NOTICE:
·

Perform this inspection with the actuator removed from the vehicle. If this inspection is performed with the actuator installed to the vehicle, the actuator will be damaged.

·

When inspecting the actuator, operate it with the lines connected via a relay. If the lines are not connected via a relay and battery voltage is directly applied to the actuator, the actuator will be damaged.



HINT:

When performing the operation described above, use the DEF relay on the main body ECU (instrument panel junction block).


C218271C10
5.917,2.385 6.417,2.385 true 5.917,2.792 6.417,2.792 true 6,2 6.333,2 true 5.74,1.833 5.74,1.333 true 5.49,2 5.094,2 true 0.833,2.271 0.49,2.271 true 1.052,2.229 0.531,1.781 true 1.229,2.208 0.958,1.531 true 1.542,2.219 1.646,1.594 true 1.719,2.229 1.948,1.813 true 2.917,1.833 2.917,1.583 2.917,1.583 2.75,1.583 true 4.677,0.563 4.854,0.729 0.177,0.167 10 false *1 2.604,1.49 2.781,1.656 0.177,0.167 10 false *1 4.979,1.906 5.167,2.083 0.188,0.177 10 false 1 6.365,1.917 6.531,2.115 0.167,0.198 10 false 2 5.719,1.115 5.969,1.281 0.25,0.167 10 false 4 6.479,2.302 6.646,2.49 0.167,0.188 10 false 5 6.438,2.708 6.604,2.865 0.167,0.156 10 false 3 0.344,1.229 0.542,1.396 0.198,0.167 10 false *a 1.542,1.427 1.917,1.583 0.375,0.156 10 false HM1 1.906,1.625 2.25,1.792 0.344,0.167 10 false HM2 0.208,2.198 0.521,2.365 0.313,0.167 10 false HL1 0.792,1.333 1.167,1.5 0.375,0.167 10 false GND 0.219,0.573 0.417,0.729 0.198,0.156 10 false *b 0.313,1.604 0.646,1.781 0.333,0.177 10 false HL2
*1 DEF Relay - -
*a Component without harness connected
(Transfer Shift Actuator Assembly)
*b HIGH to LOW


1.

After the HIGH to LOW switch is complete, inspect the limit switch.

Standard Resistance:
Tester Connection Condition Specified Condition
12 (HL1) - 10 (GND) After HIGH to LOW switch is complete Below 12.5 Ω
11 (HL2) - 10 (GND) After HIGH to LOW switch is complete 0.5 MΩ or higher


If the result is not as specified, replace the transfer shift actuator assembly (Click hereDrivetrain>VF4BM (TRANSFER / 4WD / AWD)>TRANSFER ASSEMBLY>DISASSEMBLY)

If the transfer shift actuator assembly is normal, replace the 4 wheel drive control ECU (Click hereDrivetrain>VF4BM (TRANSFER / 4WD / AWD)>4WD CONTROL ECU>REMOVAL)