Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (for LED Headlight) › 2017.08–2021.06
RM27T0E _59 Vehicle Exterior _053747 LIGHTING (EXT) _0326212 LIGHTING SYSTEM(for LED Headlight) C

LIGHTING (EXT)  LIGHTING SYSTEM(for LED Headlight)  B2424  Headlight Leveling Motor LH Communication Malfunction  B2425  Headlight Beam Level Control Motor RH Lost Communication  


DESCRIPTION

The No. 1 headlight ECU sub-assembly receives a signal from each headlight leveling motor using LIN communication.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2424 Headlight Leveling Motor LH Communication Malfunction Either condition is met:
·

Malfunction in headlight leveling motor LH

·

Open or short in headlight leveling motor LH communication circuit


·

Headlight leveling motor LH

·

Headlight unit LH

·

No. 1 headlight ECU sub-assembly LH


-
B2425 Headlight Beam Level Control Motor RH Lost Communication Either condition is met:
·

Malfunction in headlight leveling motor RH

·

Open or short in headlight leveling motor RH communication circuit


·

Headlight leveling motor RH

·

Headlight unit RH

·

Harness or connector

·

No. 1 headlight ECU sub-assembly RH

·

No. 1 headlight ECU sub-assembly LH


-

WIRING DIAGRAM

E374270E01
4.104,1.094 4.26,1.292 0.156,0.198 10 false B 4.104,2.104 4.26,2.302 0.156,0.198 10 false B 4.094,4.688 4.25,4.885 0.156,0.198 10 false B 4.104,5.688 4.26,5.885 0.156,0.198 10 false B 4.104,5.188 4.26,5.385 0.156,0.198 10 false C 4.094,1.594 4.25,1.792 0.156,0.198 10 false C 5.51,1.115 6.01,1.354 0.5,0.24 10 false LIN I/F 5.24,0.708 5.74,0.948 0.5,0.24 10 false IG 5.229,4.302 5.729,4.542 0.5,0.24 10 false IG 4.448,4.573 4.948,4.813 0.5,0.24 10 false ACTBI 4.438,0.99 4.938,1.229 0.5,0.24 10 false ACTBI 4.458,1.99 4.958,2.229 0.5,0.24 10 false ACTGI 4.438,1.448 4.938,1.688 0.5,0.24 10 false LINLI 4.448,5.063 4.948,5.302 0.5,0.24 10 false LINLI 4.427,5.594 4.927,5.833 0.5,0.24 10 false ACTGI 4.281,3.302 6.771,3.573 2.49,0.271 10 false No. 1 Headlight ECU Sub-assembly LH 4.25,6.854 6.74,7.125 2.49,0.271 10 false No. 1 Headlight ECU Sub-assembly RH 0.823,7.438 3.313,7.708 2.49,0.271 10 false : LIN Communication Line 1.885,6.802 4.375,7.073 2.49,0.271 10 false Headlight Unit RH 1.854,3.198 4.344,3.469 2.49,0.271 10 false Headlight Unit LH 0.323,2.625 2.813,2.896 2.49,0.271 10 false E 0.323,2.771 2.813,3.042 2.49,0.271 10 false Headlight Leveling Motor LH 0.292,6.198 2.781,6.469 2.49,0.271 10 false E 0.281,6.354 2.771,6.625 2.49,0.271 10 false Headlight Leveling Motor RH 1.74,5.552 2.552,5.938 0.813,0.385 10 false 3 1.74,1.979 2.552,2.365 0.813,0.385 10 false 3 1.76,4.542 2.573,4.927 0.813,0.385 10 false 1 1.74,0.969 2.552,1.354 0.813,0.385 10 false 1 1.74,1.438 2.552,1.823 0.813,0.385 10 false 2 1.75,5.042 2.563,5.427 0.813,0.385 10 false 2 4.094,5 4.906,5.385 0.813,0.385 10 false 13 4.073,1.417 4.885,1.802 0.813,0.385 10 false 13 4.115,0.906 4.927,1.292 0.813,0.385 10 false 7 4.063,1.906 4.875,2.292 0.813,0.385 10 false 17 5.875,1.448 6.375,1.688 0.5,0.24 10 false LINL 5.854,5.042 6.354,5.281 0.5,0.24 10 false LINL 6.375,5 6.875,5.24 0.5,0.24 10 false 20 6.396,1.406 6.896,1.646 0.5,0.24 10 false 20 6.302,1.594 6.802,1.833 0.5,0.24 10 false A102 6.313,5.188 6.813,5.427 0.5,0.24 10 false A103 4.125,4.5 4.938,4.885 0.813,0.385 10 false 7 4.073,5.51 4.885,5.896 0.813,0.385 10 false 17

CAUTION / NOTICE / HINT

NOTICE:

If the No. 1 headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the No. 1 headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for LED Headlight)>REGISTRATION


PROCEDURE

1.CHECK FOR DTC

b.

Turn the ignition switch to ON.


c.

Check for DTCs.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for LED Headlight)>DTC CHECK / CLEAR

OK:

DTC B2424 and B2425 are not output.



Result:
Result Proceed to
OK A
NG (DTC B2424 and B2425 are output) B
NG (DTC B2424 is output) C
NG (DTC B2425 is output) D



A

B

2.CHECK HEADLIGHT ASSEMBLY RH

C

8.CHECK HEADLIGHT UNIT LH

D

11.CHECK HARNESS AND CONNECTOR (NO. 1 HEADLIGHT ECU SUB-ASSEMBLY LH - NO. 1 HEADLIGHT ECU SUB-ASSEMBLY RH)
2.CHECK HEADLIGHT ASSEMBLY RH
a.

Disconnect the A103 No. 1 headlight ECU sub-assembly RH connector.



c.

Turn the ignition switch to ON.



Result:
Result Proceed to
Only DTC B2425 is output A
DTC B2424 and B2425 are output B



A

3.CHECK NO. 1 HEADLIGHT ECU SUB-ASSEMBLY RH

B

5.CHECK HARNESS AND CONNECTOR (NO. 1 HEADLIGHT ECU SUB-ASSEMBLY LH - NO. 1 HEADLIGHT ECU SUB-ASSEMBLY RH)
3.CHECK NO. 1 HEADLIGHT ECU SUB-ASSEMBLY RH
a.

Remove the No. 1 headlight ECU sub-assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL


b.

Connect the A103 No. 1 headlight ECU sub-assembly RH connector.



d.

Turn the ignition switch to ON.



Result:
Result Proceed to
Only DTC B2425 is output A
DTC B2424 and B2425 are output B



A

4.CHECK HEADLIGHT LEVELING MOTOR RH

B

REPLACE NO. 1 HEADLIGHT ECU SUB-ASSEMBLY RH

4.CHECK HEADLIGHT LEVELING MOTOR RH
a.

Disconnect the headlight leveling motor RH connector.


b.

Connect the No. 1 headlight ECU sub-assembly RH connectors.



d.

Turn the ignition switch to ON.



Result:
Result Proceed to
Only DTC B2425 is output A
DTC B2424 and B2425 are output B



A

B

5.CHECK HARNESS AND CONNECTOR (NO. 1 HEADLIGHT ECU SUB-ASSEMBLY LH - NO. 1 HEADLIGHT ECU SUB-ASSEMBLY RH)
a.

Disconnect the A102 No. 1 headlight ECU sub-assembly LH connector.


b.

Disconnect the A103 No. 1 headlight ECU sub-assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A102-20 (LINL) or A103-20 (LINL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK NO. 1 HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK NO. 1 HEADLIGHT ECU SUB-ASSEMBLY LH
a.

Remove the No. 1 headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL


b.

Connect the A102 No. 1 headlight ECU sub-assembly LH connector.



d.

Turn the ignition switch to ON.



Result:
Result Proceed to
Only DTC B2424 is output A
DTC B2424 and B2425 are output B



A

7.CHECK HEADLIGHT LEVELING MOTOR LH

B

REPLACE NO. 1 HEADLIGHT ECU SUB-ASSEMBLY LH

7.CHECK HEADLIGHT LEVELING MOTOR LH
a.

Disconnect the headlight leveling motor LH connector.


b.

Connect the No. 1 headlight ECU sub-assembly LH connectors.



d.

Turn the ignition switch to ON.



Result:
Result Proceed to
Only DTC B2424 is output A
DTC B2424 and B2425 are output B



A

B

8.CHECK HEADLIGHT UNIT LH
a.

Remove the headlight unit LH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for LED Headlight)>DISASSEMBLY

E377376C01
1.219,0.677 1.698,0.917 0.479,0.24 3.75,0.667 4.229,0.906 0.479,0.24 5.844,0.594 6.323,0.833 0.479,0.24 2.292,0.948 2.115,0.948 2.115,0.948 1.688,1.521 true 2.177,2.177 2,2.177 2,2.177 1.688,1.719 true 4.865,2.208 4.688,2.208 4.688,2.208 4.375,1.75 true 0.115,0.125 0.427,0.281 0.313,0.156 10 false *a 5.271,0.177 5.583,0.333 0.313,0.156 10 false *b 2.625,0.177 2.938,0.333 0.313,0.156 10 false *a 6.01,0.615 6.323,0.771 0.313,0.156 10 false E 3.958,0.677 4.271,0.833 0.313,0.156 10 false C 1.417,0.677 1.729,0.833 0.313,0.156 10 false B 4.927,2.104 5.385,2.281 0.458,0.177 10 false LINLI 2.333,0.823 2.792,1 0.458,0.177 10 false ACTBI 2.24,2.042 2.698,2.219 0.458,0.177 10 false ACTGI
*a Front view of wire harness connector
(to No. 1 Headlight ECU Sub-assembly LH)
*b Front view of wire harness connector
(to Headlight Unit Assembly LH)



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-7 (ACTBI) - E-1 Always Below 1 Ω
B-17 (ACTGI) - E-3 Always Below 1 Ω
C-13 (LINLI) - E-2 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.CHECK NO. 1 HEADLIGHT ECU SUB-ASSEMBLY LH

NG

9.CHECK NO. 1 HEADLIGHT ECU SUB-ASSEMBLY LH
a.
E377392C01
1.458,0.438 1.948,0.646 0.49,0.208 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 1.635,0.448 1.948,0.604 0.313,0.156 10 false E
*a Front view of wire harness connector
(to Headlight Leveling Motor LH)


Disconnect the headlight leveling motor LH connector.


b.

Connect the No. 1 headlight ECU sub-assembly LH connectors.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E-1 - E-3 Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

10.CHECK NO. 1 HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPLACE NO. 1 HEADLIGHT ECU SUB-ASSEMBLY LH

10.CHECK NO. 1 HEADLIGHT ECU SUB-ASSEMBLY LH
a.

Remove the No. 1 headlight ECU sub-assembly LH as a unit with the connectors still connected.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL


b.

Disconnect the A103 No. 1 headlight ECU sub-assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C-13 (LINLI) - A103-20 (LINL) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPLACE NO. 1 HEADLIGHT ECU SUB-ASSEMBLY LH

11.CHECK HARNESS AND CONNECTOR (NO. 1 HEADLIGHT ECU SUB-ASSEMBLY LH - NO. 1 HEADLIGHT ECU SUB-ASSEMBLY RH)
a.

Disconnect the A102 No. 1 headlight ECU sub-assembly LH connector.


b.

Disconnect the A103 No. 1 headlight ECU sub-assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A102-20 (LINL) - A103-20 (LINL) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

12.CHECK HEADLIGHT UNIT RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HEADLIGHT UNIT RH
a.

Remove the headlight unit RH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for LED Headlight)>DISASSEMBLY

E377376C01
1.219,0.677 1.698,0.917 0.479,0.24 3.75,0.667 4.229,0.906 0.479,0.24 5.844,0.594 6.323,0.833 0.479,0.24 2.292,0.948 2.115,0.948 2.115,0.948 1.688,1.521 true 2.177,2.177 2,2.177 2,2.177 1.688,1.719 true 4.865,2.208 4.688,2.208 4.688,2.208 4.375,1.75 true 0.115,0.125 0.427,0.281 0.313,0.156 10 false *a 5.271,0.177 5.583,0.333 0.313,0.156 10 false *b 2.625,0.177 2.938,0.333 0.313,0.156 10 false *a 6.01,0.615 6.323,0.771 0.313,0.156 10 false E 3.958,0.677 4.271,0.833 0.313,0.156 10 false C 1.417,0.677 1.729,0.833 0.313,0.156 10 false B 4.927,2.104 5.385,2.281 0.458,0.177 10 false LINLI 2.333,0.823 2.792,1 0.458,0.177 10 false ACTBI 2.24,2.042 2.698,2.219 0.458,0.177 10 false ACTGI
*a Front view of wire harness connector
(to No. 1 Headlight ECU Sub-assembly RH)
*b Front view of wire harness connector
(to Headlight Unit Assembly RH)



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-7 (ACTBI) - E-1 Always Below 1 Ω
B-17 (ACTGI) - E-3 Always Below 1 Ω
B-13 (LINLI) - E-2 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

13.CHECK NO. 1 HEADLIGHT ECU SUB-ASSEMBLY RH

NG

13.CHECK NO. 1 HEADLIGHT ECU SUB-ASSEMBLY RH
a.
E377392C01
1.458,0.438 1.948,0.646 0.49,0.208 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 1.635,0.448 1.948,0.604 0.313,0.156 10 false E
*a Front view of wire harness connector
(to Headlight Leveling Motor RH)


Disconnect the headlight leveling motor RH connector.


b.

Connect the No. 1 headlight ECU sub-assembly RH connectors.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E-1 - E-3 Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

14.CHECK NO. 1 HEADLIGHT ECU SUB-ASSEMBLY RH

NG

REPLACE NO. 1 HEADLIGHT ECU SUB-ASSEMBLY RH

14.CHECK NO. 1 HEADLIGHT ECU SUB-ASSEMBLY RH
a.

Remove the No. 1 headlight ECU sub-assembly RH as a unit with the connectors still connected.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL


b.

Disconnect the A102 No. 1 headlight ECU sub-assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C-13 (LINLI) - A102-20 (LINL) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPLACE NO. 1 HEADLIGHT ECU SUB-ASSEMBLY RH