Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (for LED Headlight) › from 2017.08
RM27T0E _59 Vehicle Exterior _053747 LIGHTING (EXT) _0326212 LIGHTING SYSTEM(for LED Headlight) J

LIGHTING (EXT)  LIGHTING SYSTEM(for LED Headlight)  Clearance Light/Daytime Running Light Circuit  


DESCRIPTION

Clearance light function:

When the main body ECU (multiplex network body ECU) receives the light control switch position signal, it sends an illumination request signal to the No. 1 headlight ECU sub-assembly and illuminates the clearance lights.


Daytime running light function:

When the operation conditions of the daytime running lights are met, the main body ECU (multiplex network body ECU) sends an illumination request signal to the No. 1 headlight ECU sub-assembly and illuminates the daytime running lights.


WIRING DIAGRAM

E374189E01
0.479,1.542 2.156,1.906 1.677,0.365 10 false Clearance Light / Daytime Running Light 3.594,1.26 4.396,1.604 0.802,0.344 10 false D 3.594,1.615 4.396,1.958 0.802,0.344 10 false D 3.594,1.969 4.396,2.313 0.802,0.344 10 false D 5.708,1.969 6.115,2.26 0.406,0.292 10 false B 5.698,1.615 6.104,1.906 0.406,0.292 10 false B 5.688,1.26 6.094,1.552 0.406,0.292 10 false B 6.01,1.604 6.49,1.917 0.479,0.313 10 false PWM1 6,1.229 6.479,1.542 0.479,0.313 10 false DRL+ 6.021,1.969 6.5,2.281 0.479,0.313 10 false DRL- 5.646,1.427 6.125,1.74 0.479,0.313 10 false 16 5.646,1.083 6.125,1.396 0.479,0.313 10 false 20 5.677,1.802 6.156,2.115 0.479,0.313 10 false 11 3.594,1.813 4.073,2.125 0.479,0.313 10 false 3 3.594,1.448 4.073,1.76 0.479,0.313 10 false 1 3.594,1.073 4.073,1.385 0.479,0.313 10 false 2 2.375,2.865 4.052,3.229 1.677,0.365 10 false Headlight Unit 1.167,2.406 2.844,2.771 1.677,0.365 10 false Headlight Unit Assembly 5.75,3.104 7.063,3.438 1.313,0.333 10 false No. 1 Headlight ECU Sub-assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Before troubleshooting, make sure that the customize setting "DRL Function" is set to "ON".

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for LED Headlight)>CUSTOMIZE PARAMETERS

·

If the No. 1 headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the No. 1 headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for LED Headlight)>REGISTRATION



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Using the GTS, perform the Active Test.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for LED Headlight)>DATA LIST / ACTIVE TEST

AFS
Tester Display Measurement Item Control Range Diagnostic Note
Clearance Light Clearance lights OFF or ON -
Daytime Running Light Daytime running lights OFF or ON -

OK:

Clearance lights and daytime running lights illuminate.



Result:
Result Proceed to
OK A
NG (LH side clearance lights and daytime running lights does not illuminate.) B
NG (RH side clearance lights and daytime running lights does not illuminate.) C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.CHECK HEADLIGHT UNIT LH

C

4.CHECK HEADLIGHT UNIT RH
2.CHECK HEADLIGHT UNIT LH
a.

Interchange the headlight unit LH with RH and connect the connectors to them.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for LED Headlight)>REMOVAL


b.

Check that the clearance light LH and daytime running light LH operate normally.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for LED Headlight)>DATA LIST / ACTIVE TEST

AFS
Tester Display Measurement Item Control Range Diagnostic Note
Clearance Light Clearance lights OFF or ON -
Daytime Running Light Daytime running lights OFF or ON -

OK:

Clearance light LH and daytime running light LH illuminate.



Result:
Proceed to
OK
NG



OK

3.CHECK HEADLIGHT UNIT LH

NG

REPLACE NO. 1 HEADLIGHT ECU SUB-ASSEMBLY LH

3.CHECK HEADLIGHT UNIT LH
a.
E377378C01
1.469,0.167 1.917,0.406 0.448,0.24 0.563,2.552 1.01,2.792 0.448,0.24 1.375,1.74 1.604,1.74 1.604,1.74 1.823,1.292 true 0.552,1.615 0.781,1.615 0.781,1.615 0.927,1.302 true 2.906,1.615 2.74,1.615 2.74,1.615 2.521,1.281 true 0.083,0.031 0.396,0.188 0.313,0.156 10 false *a 0.115,1.917 0.427,2.073 0.313,0.156 10 false *b 1.635,0.177 1.948,0.333 0.313,0.156 10 false B 0.719,2.583 1.031,2.74 0.313,0.156 10 false D 2.948,1.5 3.375,1.781 0.427,0.281 10 false DRL+ 0.188,1.49 0.615,1.708 0.427,0.219 10 false DRL- 0.896,1.635 1.406,1.885 0.51,0.25 10 false PWM1
*a Front view of wire harness connector
(to No. 1 Headlight ECU Sub-assembly LH)
*b Front view of wire harness connector
(to Headlight Unit Assembly LH)


Remove the headlight unit assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for LED Headlight)>DISASSEMBLY



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-20 (DRL+) - D-2 Always Below 1 Ω
B-16 (PWM1) - D-1 Always Below 1 Ω
B-11 (DRL-) - D-3 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HEADLIGHT UNIT RH
a.

Interchange the headlight unit RH with LH and connect the connectors to them.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for LED Headlight)>REMOVAL


b.

Check that the clearance light RH and daytime running light RH operate normally.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for LED Headlight)>DATA LIST / ACTIVE TEST

AFS
Tester Display Measurement Item Control Range Diagnostic Note
Clearance Light Clearance lights OFF or ON -
Daytime Running Light Daytime running lights OFF or ON -

OK:

Clearance light RH and daytime running light RH illuminate.



Result:
Proceed to
OK
NG



OK

5.CHECK HEADLIGHT UNIT RH

NG

REPLACE NO. 1 HEADLIGHT ECU SUB-ASSEMBLY RH

5.CHECK HEADLIGHT UNIT RH
a.
E377378C01
1.469,0.167 1.917,0.406 0.448,0.24 0.563,2.552 1.01,2.792 0.448,0.24 1.375,1.74 1.604,1.74 1.604,1.74 1.823,1.292 true 0.552,1.615 0.781,1.615 0.781,1.615 0.927,1.302 true 2.906,1.615 2.74,1.615 2.74,1.615 2.521,1.281 true 0.083,0.031 0.396,0.188 0.313,0.156 10 false *a 0.115,1.917 0.427,2.073 0.313,0.156 10 false *b 1.635,0.177 1.948,0.333 0.313,0.156 10 false B 0.719,2.583 1.031,2.74 0.313,0.156 10 false D 2.948,1.5 3.375,1.781 0.427,0.281 10 false DRL+ 0.188,1.49 0.615,1.708 0.427,0.219 10 false DRL- 0.896,1.635 1.406,1.885 0.51,0.25 10 false PWM1
*a Front view of wire harness connector
(to No. 1 Headlight ECU Sub-assembly RH)
*b Front view of wire harness connector
(to Headlight Unit Assembly RH)


Remove the headlight unit assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for LED Headlight)>DISASSEMBLY



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-20 (DRL+) - D-2 Always Below 1 Ω
B-16 (PWM1) - D-1 Always Below 1 Ω
B-11 (DRL-) - D-3 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG