1.INSTALL WIRE HARNESS CLAMP BRACKET
It is not necessary to remove the wire harness clamp brackets unless they are being replaced.
Attach the 8 wire harness clamps and install the 4 wire harness clamp brackets to the wire harness.
2.INSTALL TORQUE CONVERTER ASSEMBLY
Using a vernier caliper and straightedge, measure the dimension (A) between the automatic transmission assembly contact surface of the engine assembly (*a) and the torque converter assembly contact surface of the drive plate (*b).
(a)-(b)=(A)
| *1 | Flywheel |
| *2 | Straightedge |
| *a | Engine Assembly Surface |
| *b | Drive Plate Surface |
Align the matchmark on the automatic transmission case sub-assembly with the one on the torque converter assembly and engage the splines of the input shaft with the turbine runner splines.
| *a | Matchmark |
Install the torque converter assembly to the input shaft while keeping it horizontal.
Rotate the torque converter assembly approximately 180° and engage the splines of the stator shaft with the stator assembly.
| *1 | Front Oil Pump Oil Seal |
Do not damage the front oil pump oil seal.
Install the torque converter assembly to the input shaft while keeping it horizontal.
Rotate the torque converter assembly approximately 180° again, align the matchmark on the torque converter assembly with the one on the automatic transmission case sub-assembly and insert the key of the torque converter assembly into the groove of the oil pump drive gear.
| *1 | Front Oil Pump Oil Seal |
Do not push the torque converter assembly excessively when rotating it.
Do not damage the front oil pump oil seal.
Install the torque converter assembly to the input shaft while keeping it horizontal.
Using a vernier caliper and straightedge, measure the dimension (B) shown in the illustration and check that the dimension (B) is more than the dimension (A), which was measured in the previous step.
A + 1 mm (0.0394 in.) or more
Make sure to deduct the thickness of the straightedge.
If the automatic transmission assembly is installed to the engine assembly with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.
3516A
3.INSTALL TRANSMISSION OIL PAN HEAT INSULATOR
It is not necessary to remove the transmission oil pan heat insulator unless it is being replaced.
Install the transmission oil pan heat insulator to the automatic transmission assembly with the 3 bolts.
33823
4.INSTALL TRANSMISSION CONTROL CABLE BRACKET
It is not necessary to remove the transmission control cable bracket unless it is being replaced.
Install the transmission control cable bracket to the automatic transmission assembly with the 2 bolts.
36100
5.INSTALL TRANSFER ASSEMBLY
36478A
6.INSTALL TRANSMISSION BREATHER BRACKET
It is not necessary to remove the transmission breather bracket unless it is being replaced.
Install the 2 clamps to the transmission breather bracket.
Install the transmission breather bracket to the automatic transmission assembly with the bolt.
Connect the 3 breather hoses to the transmission breather bracket.
35000
7.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY
Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter assembly centerpiece.
Toyota Genuine Clutch Spline Grease or equivalent
Approximately 1 g (0.0353 oz.)
| *1 | Crankshaft |
| *2 | Torque Converter Assembly Centerpiece |
|
Clutch Spline Grease |
Confirm that the 2 knock pins are installed on the engine assembly and are not damaged.
While keeping the engine assembly and automatic transmission assembly horizontal, align the 2 knock pins with the holes in the automatic transmission assembly and install the 9 bolts.
Bolt length:
Bolt A: 45 mm (1.77 in.)
Bolt B: 50 mm (1.97 in.)
8.CONNECT WIRE HARNESS
Tilt down the automatic transmission assembly.
Make sure that the cooling fan and fan shroud do not contact the engine assembly when tilting the automatic transmission assembly.
Connect the wire harness to the automatic transmission assembly with the 4 bolts.
Attach the 2 wire harness clamps.
Connect the park/neutral position switch connector, transmission wire connector, 2 transmission revolution sensor connectors and transfer connector.
Push up the lever until the claw of the transmission wire connector makes a connection sound.
Connect the breather hose to the wire harness.
12371
9.INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR
It is not necessary to remove the rear No. 1 engine mounting insulator unless it is being replaced.
Install the rear No. 1 engine mounting insulator to the automatic transmission assembly with the 4 bolts.
Make sure to install the engine mounting front insulator RH so that its installation surface faces the right side of the vehicle.
w/ Heat Insulator:
Install the engine mounting heat insulator to the rear No. 1 engine mounting insulator with the bolt.
51203
10.INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY
w/ Urea SCR System:
Remove the bolt as shown in the illustration, raise the urea tank sub-assembly and hold it in position.
Only raise the urea tank enough to install the fixing bolt to the No. 3 frame crossmember sub-assembly. Do not raise it any higher.
Install the No. 3 frame crossmember sub-assembly to the body with the 4 bolts and 4 nuts.
Install the nuts so that they face the rear of the vehicle.
Hold the bolts while tightening the nuts.
w/ Urea SCR System:
Connect the urea tank sub-assembly to the No. 3 frame crossmember sub-assembly with the 2 bolts.
Connect the No. 3 frame crossmember sub-assembly to the rear No. 1 engine mounting insulator with the 4 bolts.
51225B
11.INSTALL FRONT SUSPENSION MEMBER BRACKET LH AND RH
Install the front suspension member bracket LH and RH with the 8 bolts.
| *A | w/ Urea SCR System |
| *A | w/o Urea SCR System |
12.CONNECT OIL COOLER TUBE
Connect the ends of the 2 oil cooler tubes to the automatic transmission assembly by hand.
Connect the 2 oil cooler tubes to the engine assembly with the 2 bolt.
Install the flexible hose clamp with the bolt.
Using a 17 mm union nut wrench, tighten the 2 oil cooler tubes.
| *a | Torque Wrench Fulcrum Length |
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
(See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION)
When using a union nut wrench (fulcrum length of 30 mm (1.181 in.)) + torque wrench (fulcrum length of 180 mm (7.087 in.)): 29 N*m (300 kgf*cm, 22 ft.*lbf)
35979B
13.INSTALL TRANSMISSION INSULATOR RH
33820B
14.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
Turn the control shaft lever clockwise until it stops, and then return the control shaft lever counterclockwise 2 notches to N.
Move the shift lever to N, and with the cable end lightly pushed toward the rear of the vehicle, install the transmission control cable assembly to the transmission control shaft lever LH with the nut.
Tighten the nut with no slack in the transmission control cable assembly.
Connect the transmission control shift cable assembly to the transmission control cable bracket with a new clip.
15.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT
| *a | Fulcrum Length |
| *b | Socket Adaptor (Square drive 12.7 mm to 9.5 mm)
(Tool No. 09022-3C110) |
| *c | Socket Adaptor (Square drive 9.5 mm to 12.7 mm)
(Tool No. 09022-3C100) |
| *d | 17 mm Socket Wrench
(Tool No. 09011-2C500) |
|
Turn |
Using SST, adapter, turn the crankshaft to gain access to the installation locations of the 6 drive plate and torque converter assembly setting bolts and install each bolt while holding the crankshaft pulley bolt with a wrench.
Install the black colored bolt first, and then the remaining 5 silver colored bolts.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using SST (fulcrum length of 40 mm (1.57 in.)) + torque wrench (fulcrum length of 255 mm (10.0 in.)): 41.3 N*m (421 kgf*cm, 30 ft.*lbf)
12156
16.INSTALL OIL PAN INSULATOR
Install the oil pan insulator with the 2 bolts.
Attach the 2 wire harness clamps.
28100
17.CONNECT STARTER ASSEMBLY
for 2.0 kW Type:
Install the starter assembly with the 2 bolts and nut.
for 2.7 kW Type:
Install the starter assembly with the bolt and 2 nut.
17410
18.INSTALL FRONT EXHAUST PIPE ASSEMBLY
37140
19.INSTALL FRONT PROPELLER SHAFT ASSEMBLY
37110
20.INSTALL PROPELLER SHAFT ASSEMBLY
21.ADD AUTOMATIC TRANSMISSION FLUID
22.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
(See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION)
23.INSPECT SHIFT LEVER POSITION
24.ADJUST AUTOMATIC TRANSMISSION FLUID
25.INSPECT FOR EXHAUST GAS LEAK
26.INSPECT FOR OIL LEAK
Start the engine. Make sure that there are no oil leaks from the areas that were worked on.
51450
27.INSTALL REAR ENGINE UNDER COVER ASSEMBLY
51405A
28.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
29. RESET MEMORY
If automatic transmission parts have been replaced, refer to the Parts Replacement Compensation Table to determine if any additional operations are necessary.