Home › Drivetrain › AXLE AND DIFFERENTIAL › DIFFERENTIAL SYSTEM (w/ Differential Lock) › 2017.08–2021.06
RM27T0E _52 Drivetrain _053705 AXLE AND DIFFERENTIAL _0326415 DIFFERENTIAL SYSTEM(w/ Differential Lock) J

AXLE AND DIFFERENTIAL  DIFFERENTIAL SYSTEM(w/ Differential Lock)  Rear Differential Lock Switch Circuit  


WIRING DIAGRAM

C386024E01
5.802,2.75 6.979,3.135 1.177,0.385 10 false Combination Meter Assembly 3.406,2.792 5.156,3.021 1.75,0.229 10 false 4 Wheel Drive Control ECU 3.385,2.625 3.844,2.823 0.458,0.198 10 false G53 3.385,1.833 3.698,2.031 0.313,0.198 10 false 15 3.688,1.813 3.844,2.01 0.156,0.198 10 false R 4.344,0.979 4.656,1.177 0.313,0.198 10 false IG 2.469,1.823 2.625,2.021 0.156,0.198 10 false 5 0.906,1.844 1.063,2.042 0.156,0.198 10 false E 2.208,1.844 2.365,2.042 0.156,0.198 10 false B 0.74,1.844 0.896,2.042 0.156,0.198 10 false 2 0.823,2.427 2.969,2.625 2.146,0.198 10 false G307*1, G233*2 0.833,2.583 3.198,2.948 2.365,0.365 10 false Differential Lock Switch (Combination Switch Assembly)*1 0.865,3.083 2.469,3.354 1.604,0.271 10 false Differential Lock Switch*2 0.875,3.354 4.542,3.552 3.667,0.198 10 false : CAN Communication Line 3.385,3.125 6.594,3.323 3.208,0.198 10 false *1: w/ Combination Switch 3.396,3.396 5.198,3.656 1.802,0.26 10 false *2: w/o Combination Switch

PROCEDURE

1.CHECK REAR DIFFERENTIAL LOCK INDICATOR LIGHT
a.

Turn the ignition switch to ON.


b.

w/ Combination Switch:

Press the differential lock switch (combination switch assembly).

w/o Combination Switch:

Press the differential lock switch.


c.

Check the rear differential lock indicator light.

Result:
Result Proceed to
Rear differential lock indicator light blinks or illuminates A
Rear differential lock indicator light remains off regardless of switch operation B
Rear differential lock indicator light remains illuminated regardless of switch operation C


Blinking: Blinks at 0.5 second intervals (0.5 seconds on and 0.5 seconds off)




A

END

B

2.CHECK CAN COMMUNICATION LINE

C

7.CHECK CAN COMMUNICATION LINE
2.CHECK CAN COMMUNICATION LINE
a.

Select "Bus Check" from the System Selection Menu screen, and follow the prompts on the screen to inspect the CAN bus.

(See pagePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM)

OK:

"Bus Check" indicates no malfunctions in CAN communication.


Result
Result Proceed to
DTC is not output A
DTC is output B



A

3.READ VALUE USING GTS (DIFFERENTIAL LOCK SWITCH)

B

3.READ VALUE USING GTS (DIFFERENTIAL LOCK SWITCH)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the GTS on.


d.

Turn the ignition switch to ON.


e.

Enter the following menus: Powertrain / Four Wheel Drive / Data List.


f.

According to the display on the GTS, read the Data List

Four Wheel Drive
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Rear Differential Lock Control SW Differential lock switch status/
ON or OFF
ON: ON (LOCK)
OFF: OFF (FREE)
-

OK:

w/ Combination Switch:

OK: Display changes according to differential lock switch (combination switch assembly) operation

w/o Combination Switch:

OK: Display changes according to differential lock switch operation




OK

4.INSPECT COMBINATION METER ASSEMBLY

NG

5.INSPECT COMBINATION SWITCH ASSEMBLY OR DIFFERENTIAL LOCK SWITCH
4.INSPECT COMBINATION METER ASSEMBLY
a.

Turn the ignition switch off.


b.

Perform an Active Test of the combination meter assembly using the GTS (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).


c.

Check the combination meter assembly.

OK:

The rear differential lock indicator light turns on or off in accordance with the GTS.




OK

REPLACE 4 WHEEL DRIVE CONTROL ECU

NG

5.INSPECT COMBINATION SWITCH ASSEMBLY OR DIFFERENTIAL LOCK SWITCH
a.

w/ Combination Switch:

Remove the differential lock switch (combination switch assembly) (See page Drivetrain>AXLE AND DIFFERENTIAL>REAR DIFFERENTIAL LOCK CONTROL SWITCH(w/ Combination Switch)>REMOVAL).

w/o Combination Switch:

Remove the differential lock switch (See page Drivetrain>AXLE AND DIFFERENTIAL>REAR DIFFERENTIAL LOCK CONTROL SWITCH(w/o Combination Switch)>REMOVAL).


b.

w/ Combination Switch:

Inspect the differential lock switch (combination switch assembly) (See page Drivetrain>AXLE AND DIFFERENTIAL>REAR DIFFERENTIAL LOCK POSITION SWITCH>INSPECTION).

w/o Combination Switch:

Inspect the differential lock switch (See page Drivetrain>AXLE AND DIFFERENTIAL>REAR DIFFERENTIAL LOCK CONTROL SWITCH(w/o Combination Switch)>INSPECTION).

OK:

w/ Combination Switch:

The differential lock switch (combination switch assembly) operates normally.

w/o Combination Switch:

The differential lock switch operates normally.


Result
Result Proceed to
OK A
NG w/ Combination Switch B
w/o Combination Switch C



A

6.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - COMBINATION SWITCH ASSEMBLY OR DIFFERENTIAL LOCK SWITCH)

B

C

6.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - COMBINATION SWITCH ASSEMBLY OR DIFFERENTIAL LOCK SWITCH)
a.

Disconnect the G53 4 wheel drive control ECU connector.


b.

w/ Combination Switch:

Disconnect the G307 differential lock switch (combination switch assembly) connector.


c.

w/o Combination Switch:

Disconnect the G233 differential lock switch (combination switch assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Combination Switch:
Tester Connection Condition Specified Condition
G53-15 (R) - G307-5 (B) Always Below 1 Ω
G307-2 (E) - Body ground Always Below 1 Ω
G53-15 (R) or G307-5 (B) - Body ground Always 10 kΩ or higher

w/o Combination Switch:
Tester Connection Condition Specified Condition
G53-15 (R) - G233-5 (B) Always Below 1 Ω
G233-2 (E) - Body ground Always Below 1 Ω
G53-15 (R) or G233-5 (B) - Body ground Always 10 kΩ or higher




OK

REPLACE 4 WHEEL DRIVE CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK CAN COMMUNICATION LINE
a.

Select "Bus Check" from the System Selection Menu screen, and follow the prompts on the screen to inspect the CAN bus.

(See pagePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM)

OK:

"Bus Check" indicates no malfunctions in CAN communication.



Result
Result Proceed to
DTC is not output A
DTC is output B


A

8.READ VALUE USING GTS (REAR DIFFERENTIAL LOCK INDICATOR)

B

8.READ VALUE USING GTS (REAR DIFFERENTIAL LOCK INDICATOR)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the GTS on.


d.

Turn the ignition switch to ON.


e.

Enter the following menus: Powertrain / Four Wheel Drive / Data List


f.

According to the display on the GTS, read the Data List.

Four Wheel Drive
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Rear Differential Lock Indicator Request Rear differential lock indicator light request/
Blink3, Blink2, Blink1, ON or OFF
·

Blink3: Indicator light rapidly blinks

·

Blink2: Indicator light blinks 3 times

·

Blink1: Indicator light blinks

·

ON: Indicator light illuminates

·

OFF: Indicator light turns off


·

Blinking: 0.5 second intervals (0.5 seconds on and 0.5 seconds off)

·

Rapidly blinking: 0.25 second intervals (0.25 seconds on and 0.25 seconds off)




g.

w/ Combination Switch:

Turn the differential lock switch (combination switch assembly) on and off several times and check the GTS display condition of the rear differential lock indicator light.

w/o Combination Switch:

Turn the differential lock switch on and off several times and check the GTS display condition of the rear differential lock indicator light.

Result:
Result Proceed to
Data List continues to display ON even when differential lock switch (combination switch assembly) is operated*1
Data List continues to display ON even when differential lock switch is operated*2
A
Data List display changes according to differential lock switch (combination switch assembly) operation*1
Data List display changes according to differential lock switch operation*2
B


*1: w/ Combination Switch

*2: w/o Combination Switch




A

REPLACE 4 WHEEL DRIVE CONTROL ECU

B