CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY, MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
| *A | Main Body ECU (Multiplex Network Body ECU) with 3 connectors | *B | for LHD |
| *C | for RHD | - | - |
| *1 | Main Body ECU (Multiplex Network Body ECU) | - | - |
| *A | Main Body ECU (Multiplex Network Body ECU) with 2 connectors | *B | for LHD |
| *C | for RHD | - | - |
| *1 | Main Body ECU (Multiplex Network Body ECU) | - | - |
Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Connect the driver side junction block assembly connectors.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A-32 (IG) - Body ground | None - Body ground | Ignition power supply | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V | |||
| A-31 (BECU) - Body ground | None - Body ground | Battery power supply | Always | 11 to 14 V |
| A-30 (ACC) - Body ground | None - Body ground | ACC power supply | Ignition switch ACC | 11 to 14 V |
| Ignition switch off | Below 1 V | |||
| A-11 (GND1) - Body ground | None - Body ground | Ground | Always | Below 1 Ω |
Install the main body ECU (multiplex network body ECU).
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION
Measure the voltage and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
|
*1: for LHD *2: for RHD *3: w/ Glass Hatch Opener System *4: w/ Side Step Light *5: w/ Door Illumination Light *6: w/ Footwell Light *7: for 5 Door *8: w/ Shift Lever Illumination Light |
||||
| G218-6 (FLCY) - Body ground | R - Body ground | Front door courtesy light switch assembly LH signal | Front door LH open | Below 1 V |
| Front door LH closed | Pulse generation | |||
| G218-27 (FRCY) - Body ground | B - Body ground | Front door courtesy light switch assembly RH signal | Front door RH open | Below 1 V |
| Front door RH closed | Pulse generation | |||
| 2N-30 (RCTY) - Body ground*1, *7 | R - Body ground | Rear door courtesy light switch assembly RH signal | Rear door RH open | Below 1 V |
| Rear door RH closed | Pulse generation | |||
| 2P-23 (RCTY) - Body ground*2, *7 | R - Body ground | Rear door courtesy light switch assembly RH signal | Rear door RH open | Below 1 V |
| Rear door RH closed | Pulse generation | |||
| 2Q-33 (LCTY) - Body ground*1, *7 | V - Body ground | Rear door courtesy light switch assembly LH signal | Rear door LH open | Below 1 V |
| Rear door LH closed | Pulse generation | |||
| 2O-15 (LCTY) - Body ground*2, *7 | V - Body ground | Rear door courtesy light switch assembly LH signal | Rear door LH open | Below 1 V |
| Rear door LH closed | Pulse generation | |||
| 2Q-27 (BCTY) - Body ground*1 | G - Body ground | Back door courtesy light switch assembly signal | Back door open | Below 1 V |
| Back door close | Pulse generation | |||
| 2N-27 (BCTY) - Body ground*2 | G - Body ground | Back door courtesy light switch assembly signal | Back door open | Below 1 V |
| Back door close | Pulse generation | |||
| G216-27 (GCTY) - Body ground*3 | V - Body ground | Glass hatch courtesy light switch signal | Glass hatch open | Below 1 V |
| Glass hatch close | Pulse generation | |||
| G216-4 (OILE) - Body ground*4 | W - Body ground | Foot light assembly (side step light) signal output | Foot light assembly (side step light) on | 11 to 14 V |
| Foot light assembly (side step light) off | Below 1 V | |||
| G216-25 (ILDN) - Body ground*5 | B - Body ground | Room light switch assembly down signal | Room light switch assembly down | Below 1 V |
| Room light switch assembly off | 11 to 14 V | |||
| G216-26 (ILUP) - Body ground*5 | L - Body ground | Room light switch assembly up signal | Room light switch assembly up | Below 1 V |
| Room light switch assembly off | 11 to 14 V | |||
| 2N-25 (DOME) - Body ground | GR - Body ground | Battery saving control (interior light auto cut function) signal | Battery saving control (interior light auto cut function) operating | Below 1 V |
| Battery saving control (interior light auto cut function) not operating | 11 to 14 V | |||
| G216-24 (CSPT) - Body ground*8 | GR - Body ground | Map light assembly (shift lever illumination light) signal | Ignition switch off | 11 to 14 V |
| Ignition switch ON or ACC | Below 1 V | |||
| 2N-24 (FSPT) - Body ground*6 | SB - Body ground | No. 2 interior illumination light sub-assembly (footwell light) signal | No. 2 interior illumination light sub-assembly (footwell light) off | 11 to 14 V |
| No. 2 interior illumination light sub-assembly (footwell light) on | Below 1 V | |||
| 2N-19 (ILE) - Body ground | G - Body ground | Interior lights drive output | Interior lights off (when operated by illuminated entry system) | 11 to 14 V |
| Interior lights on (when operated by illuminated entry system) | Below 1 V | |||
| 2N-31 (ILE) - Body ground | SB - Body ground | Interior lights drive output | Interior lights off (when operated by illuminated entry system) | 11 to 14 V |
| Interior lights on (when operated by illuminated entry system) | Below 1 V | |||
| 2O-41 (LSFR) - Body ground | G - Body ground | Front door unlock detection switch RH signal | Front door RH unlocked | Below 1 V |
| Ignition switch off, all doors closed and front door RH locked | Pulse generation | |||
| 2N-12 (LSFL) - Body ground | G - Body ground | Front door unlock detection switch LH signal | Front door LH unlocked | Below 1 V |
| Ignition switch off, all doors closed and front door LH locked | Pulse generation | |||
| 2Q-26 (LSWL) - Body ground*1, *7 | B - Body ground | Rear door unlock detection switch LH signal | Rear door LH unlocked | Below 1 V |
| Ignition switch off, all doors closed, rear door LH locked | Pulse generation | |||
| 2O-38 (LSWL) - Body ground*2, *7 | B - Body ground | Rear door unlock detection switch LH signal | Rear door LH unlocked | Below 1 V |
| Ignition switch off, all doors closed, rear door LH locked | Pulse generation | |||
| G216-2 (LSWR) - Body ground*7 | V - Body ground | Rear door unlock detection switch RH signal | Rear door RH unlocked | Below 1 V |
| Ignition switch off, all doors closed, rear door RH locked | Pulse generation | |||
| G218-17 (LSWB) - Body ground | SB - Body ground | Back door unlock detection switch signal | Back door unlocked | Below 1 V |
| Ignition switch off, all doors closed, back door locked | Pulse generation | |||
| G216-21 (LED1) - Body ground*5 | SB - Body ground | Front door illumination lights output | Front door illumination lights off | 11 to 14 V |
| Front door illumination lights on | Below 1 V | |||
| G216-22 (LED2) - Body ground*5, *7 | SB - Body ground | Rear door illumination lights output | Rear door illumination lights off | 11 to 14 V |
| Rear door illumination lights on | Below 1 V | |||
| 2O-33 - Body ground | G - Body ground | Taillight signal | Ignition switch ON, light control switch in tail or head position | 11 to 14 V |
| Ignition switch ON, light control switch off | Below 1 V | |||
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Entry and Start System)
Disconnect the G215 certification ECU (smart key ECU assembly) connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G215-10 (+B) - Body ground | V - Body ground | Battery power supply | Always | 11 to 14 V |
| G215-11 (E) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the G215 certification ECU (smart key ECU assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G215-17 (SWIL) - G215-12 (AGND) | B - GR | Engine switch illumination operation signal | Engine switch illumination on | 11 to 14 V |
| Engine switch illumination off | Below 1 V |
CHECK OUTER MIRROR CONTROL ECU ASSEMBLY LH (w/ Door Mirror Foot Light)
Disconnect the K12 outer mirror control ECU assembly LH connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| K12-5 (SIG) - K12-7 (GND) | G - W-B | Ignition power supply | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V | |||
| K12-6 (CPUB) - K12-7 (GND) | L - W-B | Battery power supply | Always | 11 to 14 V |
| K12-14 (BDR) - K12-7 (GND) | R - W-B | Battery power supply | Always | 11 to 14 V |
| K12-7 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the K12 outer mirror control ECU assembly LH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| z18-2 (LP+) - z18-12 (HTR-) | - | Outer rear view mirror assembly LH (foot light) output signal | Outer rear view mirror assembly LH (foot light) on | 11 to 14 V |
| Outer rear view mirror assembly LH (foot light) off | Below 1 V |
CHECK OUTER MIRROR CONTROL ECU ASSEMBLY RH (w/ Door Mirror Foot Light)
Disconnect the J12 outer mirror control ECU assembly RH connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| J12-5 (SIG) - J12-7 (GND) | G - W-B | Ignition power supply | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V | |||
| J12-6 (CPUB) - J12-7 (GND) | L - W-B | Battery power supply | Always | 11 to 14 V |
| J12-14 (BDR) - J12-7 (GND) | G - W-B | Battery power supply | Always | 11 to 14 V |
| J12-7 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the J12 outer mirror control ECU assembly RH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| z19-2 (LP+) - z19-12 (HTR-) | - | Outer rear view mirror assembly RH (foot light) output signal | Outer rear view mirror assembly RH (foot light) on | 11 to 14 V |
| Outer rear view mirror assembly RH (foot light) off | Below 1 V |