Home › Power Source / Network › POWER DISTRIBUTION › MAIN BODY ECU › 2017.08–2020.08
RM27T0E _57 Power Source / Network _053728 POWER DISTRIBUTION _0261028 MAIN BODY ECU A

POWER DISTRIBUTION  MAIN BODY ECU  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

The main body ECU (multiplex network body ECU) is not reusable.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1.INSTALL MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NOTICE:
·

Make sure that the connecting surfaces are free of foreign matter.

·

Do not touch the driver side junction block assembly connector or the main body ECU (multiplex network body ECU) connector.



a.
B195951C12
2.344,1.979 2.344,1.469 2.344,1.469 2.625,1.469 true 2.656,1.365 2.927,1.563 0.271,0.198 10 false *a 0.354,1.448 0.604,1.615 0.25,0.167 10 false *b
*a Guide Part
*b 20° or more
V100155

Housing Sidewall


Set a new main body ECU (multiplex network body ECU) to the position where the guide part of the main body ECU (multiplex network body ECU) contacts the housing sidewall of the driver side junction block assembly as shown in the illustration.

HINT:

Make sure to keep the angle at 20° or more as shown in the illustration.



b.
B197889C11
2.344,1.979 2.344,1.417 2.344,1.417 2.625,1.417 true 1.708,3.115 1.708,2.51 true 2.667,1.313 2.979,1.542 0.313,0.229 10 false *a 1.635,3.115 1.948,3.344 0.313,0.229 10 false *a
*a Guide Part
V100155

Housing Sidewall


Slide the main body ECU (multiplex network body ECU) along the housing sidewall as shown in the illustration and attach the guide.


c.
B195952C08
2.104,0.813 2.594,0.323 true 2.646,0.198 2.854,0.354 0.208,0.156 10 false *a
*a Side A


Slide the main body ECU (multiplex network body ECU) so that it contacts side A as shown in the illustration.

NOTICE:

Do not apply excessive force to the main body ECU (multiplex network body ECU).



d.
B195954C08
2.823,1.25 3.042,0.896 false 3.063,0.75 3.271,0.917 0.208,0.167 10 false *a
*a Side A Contact Portion


With the main body ECU (multiplex network body ECU) to side A of the driver side junction block assembly (point of rotation), rotate it downward as shown in the illustration.

HINT:

Rotate until ECU's lock engages into driver side junction block assembly's lock.



e.
E379386C01
0.563,2.781 0.563,3.281 0.563,3.281 1.229,3.281 true 0.469,2.708 0.469,3.281 0.469,3.281 0.281,3.281 true 0.115,3.198 0.427,3.354 0.313,0.156 10 false *1 1.271,3.198 1.583,3.354 0.313,0.156 10 false *2
*1 Main Body ECU (Multiplex Network Body ECU)
*2 Driver Side Junction Block Assembly
V100155

ECU Push Area


Press down on the push area until the claw attaches to install the main body ECU (multiplex network body ECU).

NOTICE:
·

Make sure to press only the pushing area.

·

Confirm the engagement of the main body ECU (multiplex network body ECU) and driver side junction block assembly by listening for the click sound of the lock engaging.

·

Do not hit or put your weight on the main body ECU (multiplex network body ECU) when engaging the main body ECU (multiplex network body ECU).

·

Using thumbs of both hands placed on each side of ECU.



HINT:

If a click sound cannot be heard, visually check the engagement of the lock. The engagement can also be confirmed if the main body ECU (multiplex network body ECU) and driver side junction block assembly are flush.



f.
E378112C01
0.083,0.083 0.542,0.521 0.458,0.438 12 false *A 0.083,2.427 0.542,2.865 0.458,0.438 12 false *B
*A for LHD
*B for RHD


Attach the guide.


g.

Install the wiring harness clamp bracket with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 8598A 2.INSTALL DOOR CONTROL BATTERY (w/ Door Control Battery)

Hide 3.INSTALL DRIVER SIDE JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for LHD, except 5L-E)

a.
E376848

Attach the claw to connect the lever connector.

NOTICE:

Be sure to connect the lever connector securely.



b.
E376849

Attach the claw to connect the lever connector.

NOTICE:

Be sure to connect the lever connector securely.



c.
E376830

Attach the clamp.


d.
E376829

Attach the clamp.


e.
E376828

Attach the clamp.


f.
E376836C01
0,0 0,0 false
V100135

Nut (A)
V100136

Nut (B)


Install the 2 nuts (A).

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


g.

w/ Door Control Battery:

i.

Install the 2 nuts (A) and nut (B).

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)



h.
E376850C01
0,0 0,0 false
V100135

Lever Connector
V100136

Connector (A)
V100137

Connector (B)


Attach the claw to connect the 2 lever connectors.

NOTICE:

Be sure to connect the lever connector securely.



i.

Connect the 2 connectors (A).


j.

w/ Door Control Battery:

i.

Connect the connector (B).



k.
E376834C01
0,0 0,0 false
V100135

Connector (A)
V100136

Connector (B)


for Type A:

i.

Connect the 2 connectors (A) and connector (B) to install the driver side junction block assembly with main body ECU.



l.

for Type B:

i.

Connect the 2 connectors (A) to install the driver side junction block assembly with main body ECU.



Hide 4.INSTALL DRIVER SIDE JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for LHD, 5L-E)

a.
E376844

Attach the claw to connect the lever connector.

NOTICE:

Be sure to connect the lever connector securely.



b.
E376845

Attach the claw to lock the connector lock as shown in the illustration.


c.
E376846

Attach the claw to connect the lever connector.

NOTICE:

Be sure to connect the lever connector securely.



d.
E376830

Attach the clamp.


e.
E376829

Attach the clamp.


f.
E376828

Attach the clamp.


g.
E376833

Install the 2 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


h.
E376847C01
0,0 0,0 false
V100135

Lever Connector
V100136

Connector


Attach the claw to connect the 2 lever connectors.

NOTICE:

Be sure to connect the lever connector securely.



i.

Connect the connector.


j.
E376831

Connect the 3 connectors to install the driver side junction block assembly with main body ECU.


Hide 5.INSTALL DRIVER SIDE JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for RHD, except 5L-E)

a.
E376904

Attach the claw to connect the lever connector.

NOTICE:

Be sure to connect the lever connector securely.



b.
E376905

Attach the claw to connect the lever connector.

NOTICE:

Be sure to connect the lever connector securely.



c.
E376894

Attach the clamp.


d.
E376893

Attach the clamp.


e.
E376892C01
2.188,0.208 2.49,0.354 0.302,0.146 10 false *a 1.396,3.021 1.583,3.188 0.188,0.167 10 true *b 2.26,1.094 2.438,1.25 0.177,0.156 10 true *a 1.823,3.052 2.021,3.219 0.198,0.167 10 true *b
*a Clamp (A)
*b Clamp (B)


Attach the 2 clamps (A).


f.

Install the 2 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


g.

w/ KDSS:

i.

Install the stabilizer control ECU.

Click hereSuspension>SUSPENSION CONTROL>STABILIZER CONTROL ECU>INSTALLATION



h.

Attach the 2 clamps (B).


i.
E378113C01
0,0 0,0 false
V100135

Lever Connector
V100136

Connector


Attach the claw to connect the lever connector.

NOTICE:

Be sure to connect the lever connector securely.



j.

Connect the 2 connectors.


k.

Attach the clamp.


l.
E376908C01
0,0 0,0 false
V100135

Lever Connector
V100136

Connector


Attach the claw to connect the 2 lever connectors.

NOTICE:

Be sure to connect the lever connector securely.



m.

Connect the 2 connectors.


n.
E376863C01
0,0 0,0 false
V100135

Connector (A)
V100136

Connector (B)


for Type A:

i.

Connect the 2 connectors (A) and connector (B) to install the driver side junction block assembly with main body ECU.



o.

for Type B:

i.

Connect the 2 connectors (A) to install the driver side junction block assembly with main body ECU.



Hide 6.INSTALL DRIVER SIDE JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for RHD, 5L-E)

a.
E376901

Attach the claw to connect the lever connector.

NOTICE:

Be sure to connect the lever connector securely.



b.
E376902

Attach the claw to lock the connector lock as shown in the illustration.


c.
E376903

Attach the claw to connect the lever connector.

NOTICE:

Be sure to connect the lever connector securely.



d.
E376894

Attach the clamp.


e.
E376893

Attach the clamp.


f.
E376892C01
2.188,0.208 2.49,0.354 0.302,0.146 10 false *a 1.396,3.021 1.583,3.188 0.188,0.167 10 true *b 2.26,1.094 2.438,1.25 0.177,0.156 10 true *a 1.823,3.052 2.021,3.219 0.198,0.167 10 true *b
*a Clamp (A)
*b Clamp (B)


Attach the 2 clamps (A).


g.

Install the 2 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


h.

Attach the 2 clamps (B).


i.
E378113C01
0,0 0,0 false
V100135

Lever Connector
V100136

Connector


Attach the claw to connect the lever connector.

NOTICE:

Be sure to connect the lever connector securely.



j.

Connect the 2 connectors.


k.

Attach the clamp.


l.
E376907C01
0,0 0,0 false
V100135

Lever Connector
V100136

Connector


Attach the claw to connect the 2 lever connectors.

NOTICE:

Be sure to connect the lever connector securely.



m.

Connect the connector.


n.
E376862

Connect the 3 connectors to install the driver side junction block assembly with main body ECU.


Hide 73900 7.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)

Hide 55045 8.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

Hide 55318C 9.INSTALL INSTRUMENT SIDE PANEL LH

Hide 62312B 10.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 55606 11.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 67920 13.INSTALL DOOR SCUFF PLATE ASSEMBLY LH

Hide 58191 14.INSTALL FRONT FLOOR FOOTREST (for LHD)

Hide 15.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION