Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM (except 5L-E) › from 2017.08
RM27T0E _58 Vehicle Interior _053732 LIGHTING (INT) _0326432 LIGHTING SYSTEM(except 5L-E) J

LIGHTING (INT)  LIGHTING SYSTEM(except 5L-E)  IG Signal Circuit  


DESCRIPTION

This circuit detects the ignition switch ON or off condition, and sends it to the main body ECU (multiplex network body ECU).

WIRING DIAGRAM

E346702E17
5.396,2.99 7.052,3.365 1.656,0.375 10 false Main Body ECU (Multiplex Network Body ECU) 2.896,3.021 5.542,3.302 2.646,0.281 10 false Driver Side Junction Block Assembly 2.615,2.25 4.573,2.521 1.958,0.271 10 false 2N 2.656,2.063 4.615,2.333 1.958,0.271 10 false 1 2.615,1.479 4.573,1.75 1.958,0.271 10 false 2O 2.615,1.01 4.573,1.281 1.958,0.271 10 false 2K 2.667,0.823 4.625,1.094 1.958,0.271 10 false 1 2.625,1.281 4.583,1.552 1.958,0.271 10 false 22 3.51,1.781 4.406,2.146 0.896,0.365 10 false IG NO.1 4.26,1.188 5.156,1.552 0.896,0.365 10 false ECU-IG NO.2 5.729,0.896 6.625,1.26 0.896,0.365 10 false IG 5.375,1.01 6.271,1.375 0.896,0.365 10 false A 5.385,2.25 6.281,2.615 0.896,0.365 10 false A 5.344,2.052 6.24,2.417 0.896,0.365 10 false 11 5.719,2.25 6.615,2.615 0.896,0.365 10 false GND1 5.344,0.823 6.24,1.188 0.896,0.365 10 false 32 0.781,0.948 2.417,1.24 1.635,0.292 10 false from Battery 0.135,3.01 2.01,3.229 1.875,0.219 10 false *1: w/ Entry and Start System 0.146,3.333 2.177,3.615 2.031,0.281 10 false *2: w/o Entry and Start System 0.146,1.448 1.635,2.156 1.49,0.708 10 false from Certification ECU (Smart Key ECU Assembly)*1 or Ignition Switch*2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



PROCEDURE

1.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM (except 5L-E)>DATA LIST / ACTIVE TEST

Main Body
Tester Display Measurement Item / Range Normal Condition Diagnostic Note
IG SW Ignition switch signal / OFF or ON OFF: Ignition switch off
ON: Ignition switch ON
"OFF" is also displayed for this item when the ignition switch is ACC.

OK:

Normal conditions listed above are displayed.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - BATTERY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - BATTERY AND BODY GROUND)
a.

Disconnect the driver side junction block assembly connectors.

E377404C01
0.708,0.198 1.167,0.417 0.458,0.219 2.5,0.198 2.958,0.417 0.458,0.219 5.094,0.198 5.552,0.417 0.458,0.219 0.073,0.073 0.385,0.229 0.313,0.156 10 false *a 0.844,0.24 1.156,0.396 0.313,0.156 10 false 2K 2.667,0.219 2.979,0.375 0.313,0.156 10 false 2N 5.271,0.219 5.583,0.375 0.313,0.156 10 false 2O
*a Front view of wire harness connector
(to Driver Side Junction Block Assembly)
- -



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2K-1 - Body ground Always 11 to 14 V
2O-22 - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2N-1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY
a.

Remove the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

E377405C01
0.958,0.354 1.375,0.604 0.417,0.25 2.771,0.354 3.188,0.604 0.417,0.25 5.208,0.375 5.625,0.625 0.417,0.25 3.365,1.719 3.781,1.969 0.417,0.25 5.125,2.25 5.344,2.083 5.344,2.083 5.531,2.083 true 2.49,1.958 2.667,1.958 2.667,1.958 3.094,2.26 true 0.135,0.146 0.448,0.302 0.313,0.156 10 false *a 1.073,0.375 1.396,0.646 0.323,0.271 10 false 2K 2.875,0.375 3.198,0.646 0.323,0.271 10 false 2N 5.313,0.396 5.635,0.667 0.323,0.271 10 false 2O 3.521,1.74 3.844,2.01 0.323,0.271 10 false A 5.583,1.948 5.906,2.219 0.323,0.271 10 false IG 2.052,1.823 2.51,2.104 0.458,0.281 10 false GND1
*a Component without harness connected
(Driver Side Junction Block Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2K-1 - A-32 (IG) Battery not connected to 2O-22 and 2N-1 10 kΩ or higher
Battery positive (+) → 2O-22
Battery negative (-) → 2N-1
Below 1 Ω
2N-1 - A-11 (GND1) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY