Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM (except 5L-E) › from 2017.08
RM27T0E _58 Vehicle Interior _053732 LIGHTING (INT) _0326432 LIGHTING SYSTEM(except 5L-E) J

LIGHTING (INT)  LIGHTING SYSTEM(except 5L-E)  Door Illumination Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the operation of the following lights:

·

No. 2 interior illumination light sub-assembly (door pocket light)

·

Door inside handle illumination light assembly

·

Door trim board sub-assembly (ornament illumination)


WIRING DIAGRAM

E374925E02
3.833,0.688 3.99,0.885 0.156,0.198 10 false 1 3.813,2.042 3.969,2.24 0.156,0.198 10 false 2 3.802,3.344 3.958,3.542 0.156,0.198 10 false 1 2.104,3.354 2.26,3.552 0.156,0.198 10 false 2 2.135,2.042 2.292,2.24 0.156,0.198 10 false 1 2.115,0.688 2.271,0.885 0.156,0.198 10 false 2 1.51,0.125 2.75,0.49 1.24,0.365 10 false from DOME Relay 5.667,0.698 5.927,0.938 0.26,0.24 10 false 21 5.99,0.708 6.396,0.99 0.406,0.281 10 false LED1 5.406,8.083 7.104,8.448 1.698,0.365 10 false G216 5.406,8.219 7.104,8.583 1.698,0.365 10 false Main Body ECU (Multiplex Network Body ECU) 2.344,0.698 2.5,0.896 0.156,0.198 10 false B 2.323,4.719 2.479,4.917 0.156,0.198 10 false B 3.604,4.719 3.76,4.917 0.156,0.198 10 false E 3.604,3.375 3.76,3.573 0.156,0.198 10 false - 3.604,2.052 3.76,2.25 0.156,0.198 10 false - 3.583,0.688 3.74,0.885 0.156,0.198 10 false E 3.604,6.104 3.76,6.302 0.156,0.198 10 false - 3.615,7.49 3.771,7.688 0.156,0.198 10 false - 2.344,3.375 2.5,3.573 0.156,0.198 10 false + 2.344,2.052 2.5,2.25 0.156,0.198 10 false + 2.344,6.104 2.604,6.479 0.26,0.375 10 false + 2.333,7.521 2.594,7.896 0.26,0.375 10 false + 1.677,3.99 4.708,4.26 3.031,0.271 10 false k3 1.667,4.177 5.24,4.542 3.573,0.365 10 false Front Door Inside Handle Illumination Light Assembly LH 1.563,8.115 4.594,8.385 3.031,0.271 10 false j3 1.573,8.292 5.042,8.521 3.469,0.229 10 false Front Door Inside Handle Illumination Light Assembly RH 2.104,7.469 2.26,7.667 0.156,0.198 10 false 2 2.125,6.083 2.281,6.281 0.156,0.198 10 false 1 3.813,4.677 3.969,4.875 0.156,0.198 10 false 1 2.083,4.677 2.24,4.875 0.156,0.198 10 false 2 3.833,6.021 3.99,6.219 0.156,0.198 10 false 2 3.823,7.458 3.979,7.656 0.156,0.198 10 false 1 0.583,1.333 5.375,1.635 4.792,0.302 10 false k1 0.583,1.521 5.375,1.823 4.792,0.302 10 false No. 2 Interior Illumination Light Sub-assembly LH (Front Door Pocket Light LH) 0.604,5.344 5.583,5.594 4.979,0.25 10 false j1 0.604,5.51 5.583,5.76 4.979,0.25 10 false No. 2 Interior Illumination Light Sub-assembly RH (Front Door Pocket Light RH) 1.302,6.719 5.292,6.969 3.99,0.25 10 false j2 1.313,6.896 5.302,7.146 3.99,0.25 10 false Front Door Trim Board Sub-assembly RH (Ornament Illumination)* 1.344,2.688 5.333,2.938 3.99,0.25 10 false k2 1.344,2.823 5.344,3.073 4,0.25 10 false Front Door Trim Board Sub-assembly LH (Ornament Illumination)* 0.135,8.427 3.167,8.698 3.031,0.271 10 false *: for 5 Door

E374926E02
5.979,0.698 6.594,0.896 0.615,0.198 10 false LED2 5.698,0.698 6.313,0.896 0.615,0.198 10 false 22 5.427,8.115 7.083,8.5 1.656,0.385 10 false G216 5.438,8.26 7.094,8.646 1.656,0.385 10 false Main Body ECU (Multiplex Network Body ECU) 0.625,1.354 5.49,1.552 4.865,0.198 10 false m4 0.625,1.5 5.49,1.698 4.865,0.198 10 false No. 2 Interior Illumination Light Sub-assembly LH (Rear Door Pocket Light LH) 3.844,0.688 4.094,0.948 0.25,0.26 10 false 1 2.146,0.667 2.396,0.927 0.25,0.26 10 false 2 2.135,2.052 2.385,2.313 0.25,0.26 10 false 1 3.833,2 4.083,2.26 0.25,0.26 10 false 2 2.125,3.365 2.375,3.625 0.25,0.26 10 false 2 3.844,4.656 4.094,4.917 0.25,0.26 10 false 1 3.854,6.052 4.104,6.313 0.25,0.26 10 false 2 2.115,7.438 2.365,7.698 0.25,0.26 10 false 2 3.854,3.323 4.104,3.583 0.25,0.26 10 false 1 2.115,4.688 2.365,4.948 0.25,0.26 10 false 2 2.094,6.073 2.344,6.333 0.25,0.26 10 false 1 3.844,7.458 4.094,7.719 0.25,0.26 10 false 1 0.604,5.344 5.469,5.542 4.865,0.198 10 false m3 0.594,5.49 5.458,5.688 4.865,0.198 10 false No. 2 Interior Illumination Light Sub-assembly RH (Rear Door Pocket Light RH) 2.333,4.688 2.583,4.948 0.25,0.26 10 false B 2.344,0.688 2.594,0.948 0.25,0.26 10 false B 3.604,0.688 3.854,0.948 0.25,0.26 10 false E 3.604,4.719 3.854,4.979 0.25,0.26 10 false E 3.635,3.354 3.885,3.615 0.25,0.26 10 false - 3.635,2.01 3.885,2.271 0.25,0.26 10 false - 3.646,6.063 3.896,6.323 0.25,0.26 10 false - 3.635,7.469 3.885,7.729 0.25,0.26 10 false - 2.344,7.458 2.594,7.719 0.25,0.26 10 false + 2.354,6.063 2.604,6.323 0.25,0.26 10 false + 2.344,3.344 2.594,3.604 0.25,0.26 10 false + 2.354,2.021 2.604,2.281 0.25,0.26 10 false + 1.615,8.115 4.521,8.365 2.906,0.25 10 false m5 1.604,8.281 5.167,8.542 3.563,0.26 10 false Rear Door Inside Handle Illumination Light Assembly RH 1.615,4 4.521,4.25 2.906,0.25 10 false m6 1.604,4.146 5.323,4.427 3.719,0.281 10 false Rear Door Inside Handle Illumination Light Assembly LH 1.25,6.75 6.115,6.948 4.865,0.198 10 false m7 1.427,2.688 6.292,2.885 4.865,0.198 10 false m8 1.417,2.833 6.281,3.031 4.865,0.198 10 false Rear Door Trim Board Sub-assembly LH (Ornament Illumination) 1.24,6.927 6.104,7.125 4.865,0.198 10 false Front Door Trim Board Sub-assembly RH (Ornament Illumination) 0.125,0.115 3.031,0.365 2.906,0.25 12 false for 5 Door:

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.


PROCEDURE

1.CHECK DOOR ILLUMINATION LIGHTS
a.

Check the illumination of each door illumination lights.


Result:
Result Proceed to
Front door illumination light does not illuminate. A
Rear door illumination light does not illuminate. (for 5 Door) B



A

2.PERFORM ACTIVE TEST USING GTS

B

4.PERFORM ACTIVE TEST USING GTS
2.PERFORM ACTIVE TEST USING GTS
a.

Perform the Active Test according to the display on the GTS.

Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM (except 5L-E)>DATA LIST / ACTIVE TEST

Main Body
Tester Display Measurement Item Control Range Diagnostic Note
Interior Illumination Light1 Front door illumination lights OFF or ON -

OK:

Front door illumination lights turn on.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK HARNESS AND CONNECTOR (FRONT DOOR ILLUMINATION LIGHT CIRCUIT)
3.CHECK HARNESS AND CONNECTOR (FRONT DOOR ILLUMINATION LIGHT CIRCUIT)

*: for 5 Door


a.

Disconnect the k3 front door inside handle illumination light assembly LH connector.


b.

Disconnect the j3 front door inside handle illumination light assembly RH connector.


c.

Disconnect the k2 front door trim board sub-assembly LH (ornament illumination) connector.*


d.

Disconnect the j2 front door trim board sub-assembly RH (ornament illumination) connector.*


e.

Disconnect the k1 No. 2 interior illumination light sub-assembly LH (front door pocket light LH) connector.


f.

Disconnect the j1 No. 2 interior illumination light sub-assembly RH (front door pocket light RH) connector.


g.

Enter the following menus: Body Electrical / MainBody / Active Test / Control the DOME Relay.

Main Body
Tester Display Measurement Item Control Range Diagnostic Note
Relay for Interior Light Auto Cut Function DOME relay OFF or ON OFF: DOME relay on (interior lights turn on)
ON: DOME relay off (interior lights turn off)


h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection GTS Operation Specified Condition
j1-2 (B) - Body ground Active Test is not performed (OFF) 11 to 14 V
Active Test is performed (ON) Below 1 V



i.

Disconnect the G216 main body ECU (multiplex network body ECU) connector.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
j1-1 (E) - G216-21 (LED1) Always Below 1 Ω
j1-1 (E) or G216-21 (LED1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.PERFORM ACTIVE TEST USING GTS
a.

Perform the Active Test according to the display on the GTS.

Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM (except 5L-E)>DATA LIST / ACTIVE TEST

Main Body
Tester Display Measurement Item Control Range Diagnostic Note
Interior Illumination Light2 Rear door illumination lights OFF or ON -

OK:

Rear door illumination lights turn on.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

5.CHECK HARNESS AND CONNECTOR (REAR DOOR ILLUMINATION LIGHT CIRCUIT)
5.CHECK HARNESS AND CONNECTOR (REAR DOOR ILLUMINATION LIGHT CIRCUIT)
a.

Disconnect the m6 rear door inside handle illumination light assembly LH connector.


b.

Disconnect the m5 rear door inside handle illumination light assembly RH connector.


c.

Disconnect the m8 rear door trim board sub-assembly LH (ornament illumination) connector.


d.

Disconnect the m7 rear door trim board sub-assembly RH (ornament illumination) connector.


e.

Disconnect the m4 No. 2 interior illumination light sub-assembly LH (rear door pocket light LH) connector.


f.

Disconnect the m3 No. 2 interior illumination light sub-assembly RH (rear door pocket light RH) connector.


g.

Enter the following menus: Body Electrical / MainBody / Active Test / Control the DOME Relay.

Main Body
Tester Display Measurement Item Control Range Diagnostic Note
Relay for Interior Light Auto Cut Function DOME relay OFF or ON OFF: DOME relay on (interior lights turn on)
ON: DOME relay off (interior lights turn off)


h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection GTS Operation Specified Condition
m3-2 (B) - Body ground Active Test is not performed (OFF) 11 to 14 V
Active Test is performed (ON) Below 1 V



i.

Disconnect the G216 main body ECU (multiplex network body ECU) connector.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
m3-1 (E) - G216-22 (LED2) Always Below 1 Ω
m3-1 (E) or G216-22 (LED2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR