Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM (except 5L-E) › from 2017.08
RM27T0E _58 Vehicle Interior _053732 LIGHTING (INT) _0326432 LIGHTING SYSTEM(except 5L-E) J

LIGHTING (INT)  LIGHTING SYSTEM(except 5L-E)  Footwell Light Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the operation of the following lights:

·

No. 2 interior illumination light sub-assembly LH (footwell light LH)

·

No. 2 interior illumination light sub-assembly RH (footwell light RH)


WIRING DIAGRAM

E374912E02
1.156,1.427 4.25,1.802 3.094,0.375 10 false G204 1.156,1.594 4.25,1.969 3.094,0.375 10 false No. 2 Interior Illumination Light Sub-assembly LH (Footwell Light LH) 1.198,2.875 4.292,3.25 3.094,0.375 10 false G203 1.188,3.042 4.281,3.417 3.094,0.375 10 false No. 2 Interior Illumination Light Sub-assembly RH (Footwell Light RH) 1.677,2.396 2.021,2.75 0.344,0.354 10 false 2 1.677,0.938 2.021,1.292 0.344,0.354 10 false 2 1.875,0.948 2.219,1.302 0.344,0.354 10 false B 1.865,2.375 2.208,2.729 0.344,0.354 10 false B 3.135,2.385 3.479,2.74 0.344,0.354 10 false L 3.365,2.375 3.708,2.729 0.344,0.354 10 false 1 3.344,0.896 3.688,1.25 0.344,0.354 10 false 1 3.135,0.927 3.479,1.281 0.344,0.354 10 false L 4.844,1.021 5.188,1.375 0.344,0.354 10 false 2N 4.844,0.833 5.188,1.188 0.344,0.354 10 false 24 5.615,0.833 5.958,1.188 0.344,0.354 10 false 26 5.979,0.896 6.427,1.271 0.448,0.375 10 false FSPT 5.646,1.01 5.99,1.365 0.344,0.354 10 false A 5.313,2.729 7,3.104 1.688,0.375 10 false Main Body ECU (Multiplex Network Body ECU) 4.625,1.76 5.854,2.188 1.229,0.427 10 false Driver Side Junction Block Assembly 1.313,0.302 2.833,0.781 1.521,0.479 10 false from DOME Relay

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Perform the Active Test according to the display on the GTS.

Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM (except 5L-E)>DATA LIST / ACTIVE TEST

Main Body
Tester Display Measurement Item Control Range Diagnostic Note
Fr Foot Light No. 2 interior illumination light sub-assembly (footwell light) OFF or ON -

OK:

No. 2 interior illumination light sub-assembly (footwell light) turn on.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (NO. 2 INTERIOR ILLUMINATION LIGHT SUB-ASSEMBLY [FOOTWELL LIGHT] - BATTERY)
2.CHECK HARNESS AND CONNECTOR (NO. 2 INTERIOR ILLUMINATION LIGHT SUB-ASSEMBLY [FOOTWELL LIGHT] - BATTERY)
a.
E377412C01
1.479,0.604 1.958,0.823 0.479,0.219 1.469,0.281 1.948,0.5 0.479,0.219 2.031,0.292 2.344,0.448 0.313,0.156 10 false *A 2.042,0.604 2.354,0.76 0.313,0.156 10 false *B 0.188,0.125 0.5,0.281 0.313,0.156 10 false *a 1.563,0.313 2.042,0.51 0.479,0.198 10 false G204 1.563,0.625 2.042,0.823 0.479,0.198 10 false G203
*A for LH Side
*B for RH Side
*a Front view of wire harness connector
(to No. 2 Interior Illumination Light Sub-assembly [Footwell Light])


Disconnect the No. 2 interior illumination light sub-assembly LH (footwell light LH) connector.


b.

Disconnect the No. 2 interior illumination light sub-assembly RH (footwell light RH) connector.


c.

Enter the following menus: Body Electrical / MainBody / Active Test / Control the DOME Relay.

Main Body
Tester Display Measurement Item Control Range Diagnostic Note
Relay for Interior Light Auto Cut Function DOME relay OFF or ON OFF: DOME relay on (interior lights turn on)
ON: DOME relay off (interior lights turn off)


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LH Side
Tester Connection GTS Operation Specified Condition
G204-2 (B) - Body ground Active Test is not performed (OFF) 11 to 14 V
Active Test is performed (ON) Below 1 V

for RH Side
Tester Connection GTS Operation Specified Condition
G203-2 (B) - Body ground Active Test is not performed (OFF) 11 to 14 V
Active Test is performed (ON) Below 1 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (NO. 2 INTERIOR ILLUMINATION LIGHT SUB-ASSEMBLY [FOOTWELL LIGHT] - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (NO. 2 INTERIOR ILLUMINATION LIGHT SUB-ASSEMBLY [FOOTWELL LIGHT] - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the G204 No. 2 interior illumination light sub-assembly LH (footwell light LH) connector.


b.

Disconnect the G203 No. 2 interior illumination light sub-assembly RH (footwell light RH) connector.


c.

Disconnect the 2N driver side junction block assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G204-1 (L) - 2N-24 Always Below 1 Ω
G203-1 (L) - 2N-24 Always Below 1 Ω
G204-1 (L) or 2N-24 - Body ground Always 10 kΩ or higher
G203-1 (L) or 2N-24 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY
a.
E377410C04
1.438,2.146 1.917,2.385 0.479,0.24 1.417,0.365 1.896,0.604 0.479,0.24 2.615,2.677 2.354,3 2.354,3 2.198,3 true 0.104,0.115 0.417,0.271 0.313,0.156 10 false *a 1.563,0.396 1.875,0.552 0.313,0.156 10 false 2N 1.615,2.167 1.927,2.323 0.313,0.156 10 false A 1.802,2.865 2.302,3.083 0.5,0.219 10 false FSPT
*a Component without harness connected
(Driver Side Junction Block Assembly)


Remove the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2N-24 - A-26 (FSPT) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY