CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY, MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
| *A | for LHD | *B | for RHD |
| *1 | Main Body ECU (Multiplex Network Body ECU) | - | - |
Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Connect the driver side junction block assembly connectors.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A-32 (IG) - Body ground | None - Body ground | Ignition power supply | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V | |||
| A-31 (BECU) - Body ground | None - Body ground | Battery power supply | Always | 11 to 14 V |
| A-30 (ACC) - Body ground | None - Body ground | ACC power supply | Ignition switch ACC | 11 to 14 V |
| Ignition switch off | Below 1 V | |||
| A-11 (GND1) - Body ground | None - Body ground | Ground | Always | Below 1 Ω |
Install the main body ECU (multiplex network body ECU).
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION
Measure the voltage and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
|
*1: w/ Glass Hatch Opener System *2: for LHD *3: for RHD |
||||
| G64-1 (GCTY) - 2D-4 (GND1)*1 | V - W-B | Glass hatch courtesy light switch signal | Glass hatch open | Below 1 V |
| Glass hatch closed | Pulse generation
(See waveform 1 or 2) |
|||
| G64-6 (RCTY) - 2D-4 (GND1) | R - W-B | Rear door courtesy light switch RH signal | Rear door RH open | Below 1 V |
| Rear door RH closed | 11 to 14 V | |||
| G64-19 (BCTY) - 2D-4 (GND1) | G - W-B | Back door courtesy light switch signal | Back door open | Below 1 V |
| Back door closed | Pulse generation
(See waveform 3 or 4) |
|||
| G65-3 (LCTY) - 2D-4 (GND1) | V - W-B | Rear door courtesy light switch LH signal | Rear door LH open | Below 1 V |
| Rear door LH closed | 11 to 14 V | |||
| 2D-15 (FRCY) - 2D-4 (GND1)*2
2H-26 (FRCY) - 2D-4 (GND1)*3 |
B - W-B | Front door courtesy light switch RH signal | Front door RH open | Below 1 V |
| Front door RH closed | 11 to 14 V | |||
| 2I-27 (FLCY) - 2D-4 (GND1)*2
2D-31 (FLCY) - 2D-4 (GND1)*3 |
R - W-B | Front door courtesy light switch LH signal | Front door LH open | Below 1 V |
| Front door LH closed | 11 to 14 V | |||
| 2D-18 (ILE) - 2D-4 (GND1) | G - W-B | Interior light signal | Interior light on | Below 1 V |
| Interior light off | 11 to 14 V | |||
| G64-2 (DOMR) - 2D-4 (GND1) | GR - W-B | Battery saving control (interior light auto cut function) signal | Battery saving control (interior light auto cut function) not operating | Below 1 V |
| Battery saving control (interior light auto cut function) operating | 11 to 14 V | |||
Waveform 1
| Item | Content |
|---|---|
| Terminal No. (Symbol) | G64-1 (GCTY) - 2D-4 (GND1) |
| Tool setting | 5 V/DIV., 20 ms./DIV. |
| Condition | Glass hatch closed |
Waveform 2
| Item | Content |
|---|---|
| Terminal No. (Symbol) | G64-1 (GCTY) - 2D-4 (GND1) |
| Tool setting | 5 V/DIV., 20 ms./DIV. |
| Condition | Glass hatch closed |
Waveform 3
| Item | Content |
|---|---|
| Terminal No. (Symbol) | G64-19 (BCTY) - 2D-4 (GND1) |
| Tool setting | 5 V/DIV., 20 ms./DIV. |
| Condition | Back door closed |
Waveform 4
| Item | Content |
|---|---|
| Terminal No. (Symbol) | G64-19 (BCTY) - 2D-4 (GND1) |
| Tool setting | 5 V/DIV., 20 ms./DIV. |
| Condition | Back door closed |