Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › 2017.08–2020.08
RM27T0E _58 Vehicle Interior _053736 PRE-CRASH SAFETY _0261101 PRE-CRASH SAFETY SYSTEM Y

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use these procedures to troubleshoot the pre-crash safety system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.INSPECT BATTERY VOLTAGE
2.INSPECT BATTERY VOLTAGE
a.

Measure the battery voltage with the ignition switch off.

Standard voltage:

11 to 14 V


If the voltage is below 11 V, replace or recharge the battery before proceeding to the next step.


Result:
Proceed to
NEXT



NEXT

3.INSPECT MILLIMETER WAVE RADAR SENSOR ASSEMBLY (BEAM AXIS MISALIGNMENT READING)*
3.INSPECT MILLIMETER WAVE RADAR SENSOR ASSEMBLY (BEAM AXIS MISALIGNMENT READING)*


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Turn the cruise control main switch on.


g.

Enter the following menus: Body Electrical / Pre-Crash 2 / Utility / Front Beam Axis Misalignment Reading.


h.

Check the amount of misalignment and make a note.


i.

Enter the following menus: Body Electrical / Pre-Crash 2 / Utility / Front Beam Axis Offset Reading.


j.

Check the amount of misalignment and make a note.


k.

Calculate the "Dealership Axis Offset Angle (with On-line Calibration Angle)" using the values "Front Beam Axis Misalignment Reading" and "Front Beam Axis Offset Reading".

i.

"Dealership Axis Offset Angle (with On-line Calibration Angle)" = "Front Beam Axis Misalignment Reading" - "Front Beam Axis Offset Reading"

Standard:
Dealership Axis Offset Angle (with On-line Calibration Angle):
Vertical -2.2 to 1.6 deg.
Horizontal -0.6 to 0.6 deg.




Result:
Result Proceed to
The dealership axis offset angle (with on-line calibration angle) is within the specified range. A
The dealership axis offset angle (with on-line calibration angle) is not within the specified range. B



A

4.CHECK CAN COMMUNICATION SYSTEM*

B

12.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
4.CHECK CAN COMMUNICATION SYSTEM*
a.

Using the GTS, check if the CAN communication system is functioning normally.

HINT:

Refer to CAN Bus Check in CAN Communication System.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM


OK:

CAN communication system is functioning normally.



Result:
Proceed to
OK
NG



OK

5.INSPECT WARNING LIGHT

NG

5.INSPECT WARNING LIGHT
a.

Check the condition of the warning lights on the combination meter assembly.


Result:
Result Proceed to
Warning lights other than the PCS warning light are not illuminated or flashing A
Warning lights other than the PCS warning light are illuminated or flashing B



A

6.INSPECT MULTI-INFORMATION DISPLAY

B

GO TO MALFUNCTIONING SYSTEM

6.INSPECT MULTI-INFORMATION DISPLAY
a.

Check if a pre-crash safety system warning message is displayed on the multi-information display in the combination meter assembly.


Result:
Result Proceed to
"Pre-Crash Safety Malfunction Visit Your Dealer" is displayed A
Any of the following messages is displayed:
·

"Pre-Crash Safety Unavailable"

·

"Pre-Crash Safety Unavailable Clean Sensor"

·

"Forward Camera System Unavailable"

·

"Forward Camera System Unavailable Clean Windshield"


B
Warning message is not displayed C



A

7.CHECK FOR DTCs* (PRE-CRASH SAFETY SYSTEM)

B

C

CHECK CONDITIONS WHEN PRE-CRASH SAFETY SYSTEM DID NOT OPERATE

7.CHECK FOR DTCs* (PRE-CRASH SAFETY SYSTEM)
HINT:

Refer to DTC Check / Clear.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR


a.

Check for DTCs and note any codes that are output.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR



c.

Recheck for DTCs.

i.

Attempt to duplicate the malfunction and check if the DTCs are output again.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DIAGNOSTIC TROUBLE CODE CHART



Result:
Result Proceed to
Malfunction is duplicated but DTCs are not output A
Malfunction cannot be duplicated and DTCs are not output B
DTCs are output C



A

8.PROBLEM SYMPTOMS TABLE

B

C

8.PROBLEM SYMPTOMS TABLE
HINT:

Refer to Problem Symptoms Table.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>PROBLEM SYMPTOMS TABLE


Result:
Result Proceed to
Fault is not listed in Problem Symptoms Table A
Fault is listed in Problem Symptoms Table B



A

9.OVERALL ANALYSIS AND TROUBLESHOOTING*

B

11.CONFIRMATION TEST
9.OVERALL ANALYSIS AND TROUBLESHOOTING*

NEXT

10.ADJUST, REPAIR OR REPLACE
10.ADJUST, REPAIR OR REPLACE
NOTICE:

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

11.CONFIRMATION TEST
11.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END

12.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Perform millimeter wave radar sensor assembly adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

4.CHECK CAN COMMUNICATION SYSTEM*