Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › 2017.08–2020.08
RM27T0E _58 Vehicle Interior _053736 PRE-CRASH SAFETY _0261101 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  C1A4A  Skid Control Buzzer Circuit  


DESCRIPTION

The driving support ECU assembly operates the pre-crash safety warning by sending a buzzer request signal to the skid control buzzer assembly.

If the driving support ECU assembly detects a malfunction in the skid control buzzer assembly circuit, it will store DTC C1A4A.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A4A Skid Control Buzzer Circuit When the ignition switch is ON and the pre-crash safety warning is operating, either of the following conditions is met:
·

A buzzer request signal is sent to the skid control buzzer assembly but the buzzer does not sound for 1 second or more.

·

A buzzer request signal is not sent to the skid control buzzer assembly but the buzzer sounds for 1 second or more.


·

Skid control buzzer assembly

·

Driving support ECU assembly

·

Harness or connector



WIRING DIAGRAM

C372640E09
5.042,2.146 6.99,2.531 1.948,0.385 10 false Driving Support ECU Assembly 5.021,1.906 5.479,2.104 0.458,0.198 10 false G224 5.563,0.708 5.823,0.927 0.26,0.219 10 false BZ 3.177,1.208 5.198,1.438 2.021,0.229 10 false Skid Control Buzzer Assembly 3.177,1.052 3.635,1.25 0.458,0.198 10 false A106 3.573,0.708 3.875,0.906 0.302,0.198 10 false IG1 4.219,0.719 4.479,0.958 0.26,0.24 10 false BZ 2.021,0.875 3.01,1.146 0.99,0.271 10 false ECU-IG NO. 1 0.573,0.688 1.677,1.094 1.104,0.406 10 false from IG Circuit 3.313,0.583 3.51,0.844 0.198,0.26 10 false 2 4.552,0.573 4.75,0.833 0.198,0.26 10 false 1 5.344,0.552 5.542,0.813 0.198,0.26 10 false 3

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.



PROCEDURE

1.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)

b.

Perform the Active Test according to the display on the GTS.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DATA LIST / ACTIVE TEST

NOTICE:

Perform the Active Test for 1 second or more.


HINT:

Performing the Active Test for 1 second or more causes DTC C1A4A to be stored if the DTC detection conditions are met.


Tester Display Measurement Item Control Range Diagnostic Note
PCS Crash Alarm Buzzer Skid control buzzer assembly ON / OFF Test possible with ignition switch ON, vehicle stopped



Result:
Result Proceed to
DTC C1A4A is not output A
DTC C1A4A is output B



A

B

2.CHECK TERMINAL VOLTAGE
2.CHECK TERMINAL VOLTAGE
a.
B443157C23
1.5,0.177 1.906,0.438 0.406,0.26 1.99,1.333 2.5,1.156 true 0.188,0.156 0.5,0.313 0.313,0.156 10 false *a 1.542,0.219 2,0.417 0.458,0.198 10 false A106 2.552,1.063 3.01,1.26 0.458,0.198 10 false IG1
*a Front view of wire harness connector
(to Skid Control Buzzer Assembly)


Disconnect the A106 skid control buzzer assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A106-2 (IG1) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



c.

Connect the A106 skid control buzzer assembly connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL BUZZER ASSEMBLY - BATTERY)

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY)
a.

Disconnect the A106 skid control buzzer assembly connector.


b.

Disconnect the G224 driving support ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A106-1 (BZ) - G224-3 (BZ) Always Below 1 Ω
A106-1 (BZ) or G224-3 (BZ) - Body ground Always 10 kΩ or higher



d.

Connect the G224 driving support ECU assembly connector.


e.

Connect the A106 skid control buzzer assembly connector.


Result:
Proceed to
OK
NG



OK

6.INSPECT SKID CONTROL BUZZER ASSEMBLY (CONFIRM BUZZER OPERATION)

NG

4.REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL BUZZER ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY)
4.REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL BUZZER ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY)
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
5.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)

b.

Perform the Active Test according to the display on the GTS.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DATA LIST / ACTIVE TEST

NOTICE:

Perform the Active Test for 1 second or more.


HINT:

Performing the Active Test for 1 second or more causes DTC C1A4A to be stored if the DTC detection conditions are met.


Tester Display Measurement Item Control Range Diagnostic Note
PCS Crash Alarm Buzzer Skid control buzzer assembly ON / OFF Test possible with ignition switch ON, vehicle stopped



Result:
Result Proceed to
DTC C1A4A is not output A
DTC C1A4A is output B



A

END

B

6.INSPECT SKID CONTROL BUZZER ASSEMBLY (CONFIRM BUZZER OPERATION)
6.INSPECT SKID CONTROL BUZZER ASSEMBLY (CONFIRM BUZZER OPERATION)
a.

Turn the ignition switch to ON.


b.

Check if the skid control buzzer assembly is sounding.


Result:
Result Proceed to
The skid control buzzer assembly does not sound when the ignition switch is ON A
The skid control buzzer assembly sounds continuously when the ignition switch is ON B



A

7.INSPECT SKID CONTROL BUZZER ASSEMBLY (UNIT INSPECTION)

B

8.REPLACE SKID CONTROL BUZZER ASSEMBLY
7.INSPECT SKID CONTROL BUZZER ASSEMBLY (UNIT INSPECTION)
a.

b.

Result:
Result Proceed to
Skid control buzzer assembly is abnormal A
Skid control buzzer assembly is normal B



A

8.REPLACE SKID CONTROL BUZZER ASSEMBLY

B

9.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
8.REPLACE SKID CONTROL BUZZER ASSEMBLY
a.

Replace the skid control buzzer assembly.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM WARNING BUZZER>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
9.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)

b.

Perform the Active Test according to the display on the GTS.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DATA LIST / ACTIVE TEST

NOTICE:

Perform the Active Test for 1 second or more.


HINT:

Performing the Active Test for 1 second or more causes DTC C1A4A to be stored if the DTC detection conditions are met.


Tester Display Measurement Item Control Range Diagnostic Note
PCS Crash Alarm Buzzer Skid control buzzer assembly ON / OFF Test possible with ignition switch ON, vehicle stopped



Result:
Result Proceed to
DTC C1A4A is not output A
DTC C1A4A is output B



A

END

B

REPLACE DRIVING SUPPORT ECU ASSEMBLY