Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › 2017.08–2020.08
RM27T0E _58 Vehicle Interior _053736 PRE-CRASH SAFETY _0261101 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  U023A  Lost Communication with Front Camera Module  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area
U023A Lost Communication with Front Camera Module When the ignition switch is ON, a communication error between the forward recognition camera and driving support ECU is detected for approximately 3 seconds.
·

Forward recognition camera branch line or connector

·

Forward recognition camera power source circuit

·

Forward recognition camera



WIRING DIAGRAM

C379666E10
3.792,2.906 4.771,3.094 0.979,0.188 10 false ECU-IG NO. 1 1.615,2.719 2.625,2.917 1.01,0.198 10 false from IG Circuit 5.594,2.729 6.021,3 0.427,0.271 10 false IGB 5.333,2.594 5.49,2.792 0.156,0.198 10 false 7 5.313,3.333 5.542,3.521 0.229,0.188 10 false 10 5.583,3.479 6.01,3.75 0.427,0.271 10 false GND 4.917,4.083 6.865,4.448 1.948,0.365 10 false Forward Recognition Camera 4.927,3.896 5.354,4.167 0.427,0.271 10 false W22 5.594,1.49 6.021,1.76 0.427,0.271 10 false CANL 5.594,0.865 6.021,1.135 0.427,0.271 10 false CANH 5.354,0.719 5.51,0.917 0.156,0.198 10 false 6 5.271,1.302 5.583,1.625 0.313,0.323 10 false 12 4.01,1.333 4.25,1.583 0.24,0.25 10 false 18 4.031,0.75 4.188,0.948 0.156,0.198 10 false 7 2.844,1.833 3.271,2.104 0.427,0.271 10 false A120 2.844,2 5.01,2.333 2.167,0.333 10 false Junction Connector 0.25,1.896 2.271,2.26 2.021,0.365 10 false Driving Support ECU Assembly 0.24,1.698 0.667,1.969 0.427,0.271 10 false G224 2.677,1.344 2.938,1.604 0.26,0.26 10 false 19 2.708,0.75 2.865,0.948 0.156,0.198 10 false 8 1.188,1.448 1.615,1.719 0.427,0.271 10 false CA1N 1.177,0.875 1.604,1.146 0.427,0.271 10 false CA1P 1.698,0.76 1.854,0.958 0.156,0.198 10 false 8 1.708,1.333 1.865,1.531 0.156,0.198 10 false 9

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform Forward Recognition Camera Learning.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the connectors of ECUs or wire harnesses while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.




Result:
Result Proceed to
DTC U1002 is not output A
DTC U1002 is output B



A

2.CHECK FOR OPEN IN CAN BUS MAIN LINES (FORWARD RECOGNITION CAMERA)

B

2.CHECK FOR OPEN IN CAN BUS MAIN LINES (FORWARD RECOGNITION CAMERA)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C385205C01
1.5,0.25 1.958,0.51 0.458,0.26 2.135,1.156 2.573,1.052 true 2.104,1.448 2.573,1.594 true 0.063,0.083 0.406,0.292 0.344,0.208 10 false *a 2.625,0.948 3.104,1.146 0.479,0.198 10 false CANH 2.625,1.521 3.104,1.719 0.479,0.198 10 false CANL 1.583,0.302 1.958,0.5 0.375,0.198 10 false W22
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the W22 forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W22-6 (CANH) - W22-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



d.

Connect the W22 forward recognition camera connector.


e.

Connect the cable to the negative (-) battery terminal.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE)

NG

REPAIR OR REPLACE CAN BUS MAIN LINE OR CONNECTOR (JUNCTION CONNECTOR - FORWARD RECOGNITION CAMERA)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C385205C02
1.479,0.25 1.938,0.51 0.458,0.26 0.854,1.625 1.25,1.438 true 1.792,1.469 2.073,1.833 true 0.063,0.083 0.406,0.292 0.344,0.208 10 false *a 0.552,1.604 0.844,1.802 0.292,0.198 10 false IGB 1.979,1.865 2.458,2.063 0.479,0.198 10 false GND 1.552,0.302 1.927,0.5 0.375,0.198 10 false W22
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the W22 forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W22-10 (GND) - Body ground Always Below 1 Ω



d.

Connect the cable to the negative (-) battery terminal.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
W22-7 (IGB) - Body ground Ignition switch ON 11 to 14 V



f.

Connect the W22 forward recognition camera connector.


Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)