Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › 2017.08–2020.08
RM27T0E _58 Vehicle Interior _053736 PRE-CRASH SAFETY _0261101 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  U1002  Lost Communication with Gateway Module  


DESCRIPTION

This DTC is stored when the driving support ECU assembly cannot receive signals from the forward recognition camera or millimeter wave radar sensor assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
U1002 Lost Communication with Gateway Module After the ignition switch is turned on, communication between the driving support ECU and any of the following components is abnormal for 2 seconds or more
·

Forward recognition camera

·

Millimeter wave radar sensor assembly


·

CAN bus main line, CAN bus branch line or connector

·

Forward recognition camera

·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly

·

Junction Connector



WIRING DIAGRAM

B429439E25
0.094,2.01 2,2.365 1.906,0.354 10 false Millimeter Wave Radar Sensor Assembly 0.104,1.823 0.563,2.021 0.458,0.198 10 false A100 5.177,3.094 7.125,3.281 1.948,0.188 10 false Driving Support ECU Assembly 5.188,2.896 5.646,3.094 0.458,0.198 10 false G224 0.083,4.302 2,4.49 1.917,0.188 10 false Forward Recognition Camera 0.073,4.104 0.531,4.302 0.458,0.198 10 false W22 0.906,3.083 1.521,3.281 0.615,0.198 10 false CANH 0.938,3.833 1.552,4.031 0.615,0.198 10 false CANL 1.365,3.083 1.521,3.281 0.156,0.198 10 false 6 1.344,3.625 1.656,3.823 0.313,0.198 10 false 12 3.063,4.323 5.104,4.563 2.042,0.24 10 false Junction Connector 3.052,4.135 3.51,4.333 0.458,0.198 10 false A120 3.146,3.094 3.427,3.271 0.281,0.177 10 false 7 3.083,3.604 3.396,3.802 0.313,0.198 10 false 18 5.771,1.906 5.927,2.104 0.156,0.198 10 false 8 5.771,2.438 5.927,2.635 0.156,0.198 10 false 9 4.094,1.906 4.344,2.115 0.25,0.208 10 false 8 4.083,2.427 4.396,2.625 0.313,0.198 10 false 19 0.917,0.771 1.531,0.969 0.615,0.198 10 false CA1P 0.927,1.51 1.542,1.708 0.615,0.198 10 false CA1N 5.958,2.01 6.573,2.208 0.615,0.198 10 false CA1P 5.958,2.552 6.573,2.75 0.615,0.198 10 false CA1N 1.375,0.771 1.531,0.969 0.156,0.198 10 false 5 3.094,0.75 3.344,0.948 0.25,0.198 10 false 11 1.365,1.302 1.521,1.5 0.156,0.198 10 false 6 3.094,1.281 3.406,1.479 0.313,0.198 10 false 22

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.

·

When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle. As a result, a DTC may be stored.

·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform Forward Recognition Camera Learning.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK CAN BUS LINE (MALFUNCTION CONFIRMATION)
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.


c.
C334337C38
1.448,0.656 1.906,0.896 0.458,0.24 1.198,1.406 1,0.625 true 1.073,1.417 0.781,0.885 true 2.042,1.396 2.302,0.667 true 0.813,2.406 1.073,1.677 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 1.51,0.688 1.969,0.885 0.458,0.198 10 false G224 0.615,0.521 1.229,0.719 0.615,0.198 10 false CA1P 0.396,0.802 1.01,1 0.615,0.198 10 false CA1N 0.458,2.344 1.073,2.542 0.615,0.198 10 false GND 2.344,0.573 2.958,0.771 0.615,0.198 10 false B
*a Component with harness connected
(Driving Support ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
G224-8 (CA1P) - G224-9 (CA1N) Cable disconnected from negative (-) battery terminal 54 to 69 Ω Below 54 Ω:
Short circuit between bus lines
70 Ω or more:
Open circuit in a main bus line or driving support ECU assembly branch line
G224-8 (CA1P) - G224-28 (GND) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω:
CANH ground short
G224-9 (CA1N) - G224-28 (GND) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω:
CANH ground short
G224-8 (CA1P) - G224-7 (B) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ:
CANH +B short
G224-9 (CA1N) - G224-7 (B) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ:
CANH +B short



d.

Connect the cable to the negative (-) battery terminal.


Result:
Result Proceed to
OK A
NG (Open circuit in main line or Driving support ECU assembly branch line) B
NG (Short circuit between main lines) C
NG (Short to +B or ground) D



A

2.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)

B

3.CHECK FOR OPEN IN CAN BUS BRANCH LINES (DRIVING SUPPORT ECU ASSEMBLY)

C

8.CHECK FOR SHORT BETWEEN CAN BUS LINES (FORWARD RECOGNITION CAMERA)

D

12.CHECK FOR SHORT IN CAN BUS LINE (FORWARD RECOGNITION CAMERA)
2.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.




Result:
Result Proceed to
DTC U1002 is not output A
DTC U1002 is output B



A

B

REPLACE DRIVING SUPPORT ECU ASSEMBLY

3.CHECK FOR OPEN IN CAN BUS BRANCH LINES (DRIVING SUPPORT ECU ASSEMBLY)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
A380143C72
1.531,0.188 1.979,0.417 0.448,0.229 2.323,0.958 2.479,0.208 true 2.479,0.969 2.729,0.448 true 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 1.594,0.219 2.052,0.417 0.458,0.198 10 false G224 2.51,0.073 3.052,0.302 0.542,0.229 10 false CA1P 2.76,0.313 3.302,0.542 0.542,0.229 10 false CA1N
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Disconnect the G224 driving support ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G224-8 (CA1P) - G224-9 (CA1N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


HINT:

If the resistance is between 108 and 132 Ω, there may be an open in a CAN bus main line. If the value is 132 Ω or more, there may be an open in a CAN bus branch line between the junction connector and the driving support ECU or a connector may be disconnected.



d.

Connect the G224 driving support ECU assembly connector.


e.

Connect the cable to the negative (-) battery terminal.


Result:
Proceed to
OK
NG



OK

4.CHECK FOR OPEN IN CAN BUS MAIN LINES (JUNCTION CONNECTOR)

NG

7.CHECK FOR OPEN IN CAN BUS BRANCH LINES (DRIVING SUPPORT ECU ASSEMBLY)
4.CHECK FOR OPEN IN CAN BUS MAIN LINES (JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C385236C01
1.448,0.104 2,0.354 0.552,0.25 1.458,2.031 1.656,2.031 1.656,2.031 1.854,1.448 true 1.083,0.469 1.219,0.469 1.219,0.469 1.781,1.135 true 2.771,0.656 2.656,0.656 2.656,0.656 2.542,1.135 true 2.698,1.917 2.583,1.917 2.583,1.917 2.531,1.427 true 0.927,1.938 1.542,2.135 0.615,0.198 10 false CANL*b 0.469,0.406 1.083,0.604 0.615,0.198 10 false CANH*b 1.563,0.146 2.021,0.323 0.458,0.177 10 false A120 0.219,0.115 0.677,0.292 0.458,0.177 10 false *a 2.813,0.583 3.427,0.781 0.615,0.198 10 false CA1P*c 2.74,1.844 3.354,2.042 0.615,0.198 10 false CA1N*c
*a Front view of wire harness connector
(to Junction Connector)
*b to Forward Recognition Camera
*c to Millimeter Wave Radar Sensor Assembly


Disconnect the A120 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
A120-7 (CANH) - A120-18 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Forward Recognition Camera
A120-11 (CA1P) - A120-22 (CA1N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Millimeter Wave Radar Sensor Assembly



d.

Connect the A120 junction connector.


e.

Connect the cable to the negative (-) battery terminal.


Result:
Result Proceed to
OK A
NG (Forward Recognition Camera Main Line) B
NG (Millimeter Wave Radar Sensor Assembly Main Line) C



A

REPLACE JUNCTION CONNECTOR

B

5.CHECK FOR OPEN IN CAN BUS MAIN LINES (FORWARD RECOGNITION CAMERA)

C

6.CHECK FOR OPEN IN CAN BUS MAIN LINES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
5.CHECK FOR OPEN IN CAN BUS MAIN LINES (FORWARD RECOGNITION CAMERA)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C385205C01
1.5,0.25 1.958,0.51 0.458,0.26 2.135,1.156 2.573,1.052 true 2.104,1.448 2.573,1.594 true 0.063,0.083 0.406,0.292 0.344,0.208 10 false *a 2.625,0.948 3.104,1.146 0.479,0.198 10 false CANH 2.625,1.521 3.104,1.719 0.479,0.198 10 false CANL 1.583,0.302 1.958,0.5 0.375,0.198 10 false W22
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the W22 forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W22-6 (CANH) - W22-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



d.

Connect the W22 forward recognition camera connector.


e.

Connect the cable to the negative (-) battery terminal.


Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE CAN BUS MAIN LINE OR CONNECTOR (JUNCTION CONNECTOR - FORWARD RECOGNITION CAMERA)

6.CHECK FOR OPEN IN CAN BUS MAIN LINES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
A380144C53
1.458,0.167 1.927,0.385 0.469,0.219 1.083,1.75 1.427,1.229 true 1.615,1.24 1.823,1.771 true 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 1.542,0.188 1.948,0.365 0.406,0.177 10 false A100 0.906,1.781 1.365,1.99 0.458,0.208 10 false CA1P 1.688,1.813 2.302,2.01 0.615,0.198 10 false CA1N
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the A100 millimeter wave radar sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A100-5 (CA1P) - A100-6 (CA1N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



d.

Connect the A100 millimeter wave radar sensor assembly connector.


e.

Connect the cable to the negative (-) battery terminal.


Result:
Proceed to
OK
NG



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS MAIN LINE OR CONNECTOR (JUNCTION CONNECTOR - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

7.CHECK FOR OPEN IN CAN BUS BRANCH LINES (DRIVING SUPPORT ECU ASSEMBLY)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
A380143C72
1.531,0.188 1.979,0.417 0.448,0.229 2.323,0.958 2.479,0.208 true 2.479,0.969 2.729,0.448 true 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 1.594,0.219 2.052,0.417 0.458,0.198 10 false G224 2.51,0.073 3.052,0.302 0.542,0.229 10 false CA1P 2.76,0.313 3.302,0.542 0.542,0.229 10 false CA1N
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Disconnect the G224 driving support ECU assembly connector.


c.
C385236C02
1.448,0.104 2,0.354 0.552,0.25 2.51,0.313 2.396,0.313 2.396,0.313 2.052,1.146 true 2.281,1.958 2.167,1.958 2.167,1.958 2.052,1.438 true 1.563,0.146 2.021,0.323 0.458,0.177 10 false A120 0.219,0.115 0.677,0.292 0.458,0.177 10 false *a 2.563,0.25 3.177,0.448 0.615,0.198 10 false CA1P*b 2.385,1.875 3,2.073 0.615,0.198 10 false CA1N*b
*a Front view of wire harness connector
(to Junction Connector)
*b to Driving Support ECU Assembly


Disconnect the A120 junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A120-8 (CA1P) - G224-8 (CA1P) Cable disconnected from negative (-) battery terminal Below 1 Ω
A120-19 (CA1N) - G224-9 (CA1N) Cable disconnected from negative (-) battery terminal Below 1 Ω



e.

Connect the A120 junction connector.


f.

Connect the G224 driving support ECU assembly connector.


g.

Connect the cable to the negative (-) battery terminal.


Result:
Proceed to
OK
NG



OK

REPLACE CAN JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE (JUNCTION CONNECTOR - DRIVING SUPPORT ECU ASSEMBLY)

8.CHECK FOR SHORT BETWEEN CAN BUS LINES (FORWARD RECOGNITION CAMERA)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C385205C01
1.5,0.25 1.958,0.51 0.458,0.26 2.135,1.156 2.573,1.052 true 2.104,1.448 2.573,1.594 true 0.063,0.083 0.406,0.292 0.344,0.208 10 false *a 2.625,0.948 3.104,1.146 0.479,0.198 10 false CANH 2.625,1.521 3.104,1.719 0.479,0.198 10 false CANL 1.583,0.302 1.958,0.5 0.375,0.198 10 false W22
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the W22 forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W22-6 (CANH) - W22-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



d.

Connect the W22 forward recognition camera connector.


e.

Connect the cable to the negative (-) battery terminal.


Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

9.CHECK FOR SHORT BETWEEN CAN BUS LINES (JUNCTION CONNECTOR)
9.CHECK FOR SHORT BETWEEN CAN BUS LINES (JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C385236C03
1.448,0.104 2,0.354 0.552,0.25 1.458,2.031 1.656,2.031 1.656,2.031 1.854,1.448 true 1.083,0.469 1.219,0.469 1.219,0.469 1.781,1.135 true 2.771,0.656 2.656,0.656 2.656,0.656 2.542,1.135 true 2.771,1.802 2.656,1.802 2.656,1.802 2.542,1.427 true 2.49,0.177 2.375,0.177 2.375,0.177 2.052,1.135 true 2.198,2.021 2.083,2.021 2.083,2.021 2.042,1.427 true 0.927,1.938 1.542,2.135 0.615,0.198 10 false CANL*b 0.469,0.406 1.083,0.604 0.615,0.198 10 false CANH*b 1.563,0.146 2.021,0.323 0.458,0.177 10 false A120 0.219,0.115 0.677,0.292 0.458,0.177 10 false *a 2.813,0.583 3.427,0.781 0.615,0.198 10 false CA1P*c 2.813,1.719 3.427,1.917 0.615,0.198 10 false CA1N*c 2.552,0.115 3.167,0.313 0.615,0.198 10 false CA1P*d 2.24,1.917 2.854,2.115 0.615,0.198 10 false CA1N*d
*a Front view of wire harness connector
(to Junction Connector)
*b to Forward Recognition Camera
*c to Millimeter Wave Radar Sensor Assembly
*d to Driving Support ECU Assembly


Disconnect the A120 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
A120-7 (CANH) - A120-18 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Forward Recognition Camera
A120-11 (CA1P) - A120-22 (CA1N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Millimeter Wave Radar Sensor Assembly
A120-8 (CA1P) - A120-19 (CA1N) Cable disconnected from negative (-) battery terminal 200 Ω or higher Driving Support ECU Assembly



d.

Connect the A120 junction connector.


e.

Connect the cable to the negative (-) battery terminal.


Result:
Result Proceed to
OK A
NG (Forward Recognition Camera Main Line) B
NG (Millimeter Wave Radar Sensor Assembly Main Line) C
NG (Driving Support ECU Assembly Branch Line) D



A

REPLACE JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN BUS MAIN LINE OR CONNECTOR (JUNCTION CONNECTOR - FORWARD RECOGNITION CAMERA)

C

10.CHECK FOR SHORT BETWEEN CAN BUS LINES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

D

11.CHECK FOR SHORT BETWEEN CAN BUS LINES (DRIVING SUPPORT ECU ASSEMBLY)
10.CHECK FOR SHORT BETWEEN CAN BUS LINES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
A380144C53
1.458,0.167 1.927,0.385 0.469,0.219 1.083,1.75 1.427,1.229 true 1.615,1.24 1.823,1.771 true 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 1.542,0.188 1.948,0.365 0.406,0.177 10 false A100 0.906,1.781 1.365,1.99 0.458,0.208 10 false CA1P 1.688,1.813 2.302,2.01 0.615,0.198 10 false CA1N
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the A100 millimeter wave radar sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A100-5 (CA1P) - A100-6 (CA1N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



d.

Connect the A100 millimeter wave radar sensor assembly connector.


e.

Connect the cable to the negative (-) battery terminal.


Result:
Proceed to
OK
NG



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS MAIN LINE OR CONNECTOR (JUNCTION CONNECTOR - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

11.CHECK FOR SHORT BETWEEN CAN BUS LINES (DRIVING SUPPORT ECU ASSEMBLY)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
A380143C72
1.531,0.188 1.979,0.417 0.448,0.229 2.323,0.958 2.479,0.208 true 2.479,0.969 2.729,0.448 true 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 1.594,0.219 2.052,0.417 0.458,0.198 10 false G224 2.51,0.073 3.052,0.302 0.542,0.229 10 false CA1P 2.76,0.313 3.302,0.542 0.542,0.229 10 false CA1N
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Disconnect the G224 driving support ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G224-8 (CA1P) - G224-9 (CA1N) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



d.

Connect the G224 driving support ECU assembly connector.


e.

Connect the cable to the negative (-) battery terminal.


Result:
Proceed to
OK
NG



OK

REPLACE DRIVING SUPPORT ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS BRANCH LINE OR CONNECTOR (JUNCTION CONNECTOR - DRIVING SUPPORT ECU ASSEMBLY)

12.CHECK FOR SHORT IN CAN BUS LINE (FORWARD RECOGNITION CAMERA)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C385205C01
1.5,0.25 1.958,0.51 0.458,0.26 2.135,1.156 2.573,1.052 true 2.104,1.448 2.573,1.594 true 0.063,0.083 0.406,0.292 0.344,0.208 10 false *a 2.625,0.948 3.104,1.146 0.479,0.198 10 false CANH 2.625,1.521 3.104,1.719 0.479,0.198 10 false CANL 1.583,0.302 1.958,0.5 0.375,0.198 10 false W22
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the W22 forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W22-6 (CANH) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
W22-12 (CANL) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
W22-6 (CANH) - +B Cable disconnected from negative (-) battery terminal 6 kΩ or higher
W22-12 (CANL) - +B Cable disconnected from negative (-) battery terminal 6 kΩ or higher



d.

Connect the W22 forward recognition camera connector.


e.

Connect the cable to the negative (-) battery terminal.


Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

13.CHECK FOR SHORT IN CAN BUS LINE (JUNCTION CONNECTOR)
13.CHECK FOR SHORT IN CAN BUS LINE (JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C385236C03
1.448,0.104 2,0.354 0.552,0.25 1.458,2.031 1.656,2.031 1.656,2.031 1.854,1.448 true 1.083,0.469 1.219,0.469 1.219,0.469 1.781,1.135 true 2.771,0.656 2.656,0.656 2.656,0.656 2.542,1.135 true 2.771,1.802 2.656,1.802 2.656,1.802 2.542,1.427 true 2.49,0.177 2.375,0.177 2.375,0.177 2.052,1.135 true 2.198,2.021 2.083,2.021 2.083,2.021 2.042,1.427 true 0.927,1.938 1.542,2.135 0.615,0.198 10 false CANL*b 0.469,0.406 1.083,0.604 0.615,0.198 10 false CANH*b 1.563,0.146 2.021,0.323 0.458,0.177 10 false A120 0.219,0.115 0.677,0.292 0.458,0.177 10 false *a 2.813,0.583 3.427,0.781 0.615,0.198 10 false CA1P*c 2.813,1.719 3.427,1.917 0.615,0.198 10 false CA1N*c 2.552,0.115 3.167,0.313 0.615,0.198 10 false CA1P*d 2.24,1.917 2.854,2.115 0.615,0.198 10 false CA1N*d
*a Front view of wire harness connector
(to Junction Connector)
*b to Forward Recognition Camera
*c to Millimeter Wave Radar Sensor Assembly
*d to Driving Support ECU Assembly


Disconnect the A120 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
A120-7 (CANH) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher Forward Recognition Camera
A120-18 (CANL) - Body ground
A120-7 (CANH) - +B 6 kΩ or higher
A120-18 (CANL) - +B
A120-11 (CA1P) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher Millimeter Wave Radar Sensor Assembly
A120-22 (CA1N) - Body ground
A120-11 (CA1P) - +B 6 kΩ or higher
A120-22 (CA1N) - +B
A120-8 (CA1P) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher Driving Support ECU Assembly
A120-19 (CA1N) - Body ground
A120-8 (CA1P) - +B 6 kΩ or higher
A120-19 (CA1N) - +B



d.

Connect the A120 junction connector.


e.

Connect the cable to the negative (-) battery terminal.


Result:
Result Proceed to
OK A
NG (Forward Recognition Camera Main Line) B
NG (Millimeter Wave Radar Sensor Assembly Main Line) C
NG (Driving Support ECU Assembly Branch Line) D



A

REPLACE JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN BUS MAIN LINE OR CONNECTOR (JUNCTION CONNECTOR - FORWARD RECOGNITION CAMERA)

C

14.CHECK FOR SHORT IN CAN BUS LINE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

D

15.CHECK FOR SHORT IN CAN BUS LINE (DRIVING SUPPORT ECU ASSEMBLY)
14.CHECK FOR SHORT IN CAN BUS LINE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
A380144C53
1.458,0.167 1.927,0.385 0.469,0.219 1.083,1.75 1.427,1.229 true 1.615,1.24 1.823,1.771 true 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 1.542,0.188 1.948,0.365 0.406,0.177 10 false A100 0.906,1.781 1.365,1.99 0.458,0.208 10 false CA1P 1.688,1.813 2.302,2.01 0.615,0.198 10 false CA1N
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the A100 millimeter wave radar sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A100-5 (CA1P) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A100-6 (CA1N) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A100-5 (CA1P) - +B Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A100-6 (CA1N) - +B Cable disconnected from negative (-) battery terminal 6 kΩ or higher



d.

Connect the A100 millimeter wave radar sensor assembly connector.


e.

Connect the cable to the negative (-) battery terminal.


Result:
Proceed to
OK
NG



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS MAIN LINE OR CONNECTOR (JUNCTION CONNECTOR - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

15.CHECK FOR SHORT IN CAN BUS LINE (DRIVING SUPPORT ECU ASSEMBLY)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
A380143C72
1.531,0.188 1.979,0.417 0.448,0.229 2.323,0.958 2.479,0.208 true 2.479,0.969 2.729,0.448 true 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 1.594,0.219 2.052,0.417 0.458,0.198 10 false G224 2.51,0.073 3.052,0.302 0.542,0.229 10 false CA1P 2.76,0.313 3.302,0.542 0.542,0.229 10 false CA1N
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Disconnect the G224 driving support ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G224-8 (CA1P) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G224-9 (CA1N) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G224-8 (CA1P) - +B Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G224-9 (CA1N) - +B Cable disconnected from negative (-) battery terminal 6 kΩ or higher



d.

Connect the G224 driving support ECU assembly connector.


e.

Connect the cable to the negative (-) battery terminal.


Result:
Proceed to
OK
NG



OK

REPLACE DRIVING SUPPORT ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS BRANCH LINE OR CONNECTOR (JUNCTION CONNECTOR - DRIVING SUPPORT ECU ASSEMBLY)