Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM (w/ Reverse Shift-linked Mirror) › from 2017.08
RM27T0E _59 Vehicle Exterior _053745 MIRROR (EXT) _0327116 POWER MIRROR CONTROL SYSTEM(w/ Reverse Shift-linked Mirror) U

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/ Reverse Shift-linked Mirror)  TERMINALS OF ECU  


CHECK OUTER MIRROR CONTROL ECU ASSEMBLY LH


B343031E29
2.427,0.146 2.802,0.396 0.375,0.25 4.438,0.146 4.813,0.396 0.375,0.25 2.51,0.188 2.833,0.385 0.323,0.198 10 false z18 4.51,0.188 4.969,0.385 0.458,0.198 10 false K12

a.

Disconnect the K12 outer mirror control ECU assembly LH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition

*1: for LHD

*2: for RHD

K12-5 (SIG) - K12-7 (GND) G - W-B Power source Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
K12-6 (CPUB) - K12-7 (GND) L - W-B Power source Always 11 to 14 V
K12-14 (BDR) - K12-7 (GND) R - W-B*1
G - W-B*2
Power source Always 11 to 14 V
K12-7 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the K12 outer mirror control ECU assembly LH connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
z18-3 (MR) - Body ground SB - Body ground Power retract mirror motor drive voltage
·

Ignition switch ACC

·

Outer rear view mirror assembly being retracted


11 to 14 V
·

Ignition switch ACC

·

Outer rear view mirror assembly stopped


Below 1 V
z18-11 (MF) - Body ground LG - Body ground Power retract mirror motor drive voltage
·

Ignition switch ACC

·

Outer rear view mirror assembly returning


11 to 14 V
·

Ignition switch ACC

·

Outer rear view mirror assembly stopped


Below 1 V
z18-1 (MV) - Body ground V - Body ground Mirror motor drive voltage
·

Ignition switch ACC

·

Mirror surface stopped


Below 1 V
·

Ignition switch ACC

·

Mirror surface moving downward or left


Below 1 V
·

Ignition switch ACC

·

Mirror surface moving upward


11 to 14 V
z18-9 (MH) - Body ground BR - Body ground Mirror motor drive voltage
·

Ignition switch ACC

·

Mirror surface stopped


Below 1 V
·

Ignition switch ACC

·

Mirror surface moving upward or right


Below 1 V
·

Ignition switch ACC

·

Mirror surface moving left


11 to 14 V
z18-10 (M+) - Body ground R - Body ground Mirror motor drive voltage
·

Ignition switch ACC

·

Mirror surface stopped


Below 1 V
·

Ignition switch ACC

·

Mirror surface moving upward or left


Below 1 V
·

Ignition switch ACC

·

Mirror surface moving downward or right


11 to 14 V
z18-4 (HTR+) - z18-12 (HTR-)* B - W Mirror heater drive voltage
·

Ignition switch ON

·

Rear window defogger switch (mirror heater switch) on


11 to 14 V
·

Ignition switch ON

·

Rear window defogger switch (mirror heater switch) off


Below 1 V
z18-5 (VDD) - z18-14 (GND) R-W - GR Mirror position sensor power supply Ignition switch ON 4.5 to 5.5 V
Ignition switch off Below 1 V
z18-6 (VSSR) - Body ground Y-B - Body ground Vertical direction position sensor signal
·

Ignition switch ACC

·

Mirror surface moving upward or downward


Changes within range of 0 to 5 V
z18-13 (HSSR) - Body ground P - Body ground Horizontal direction position sensor signal
·

Ignition switch ACC

·

Mirror surface moving left or right


Changes within range of 0 to 5 V

*: w/ Mirror Heater




CHECK OUTER MIRROR CONTROL ECU ASSEMBLY RH


B343031E30
2.427,0.146 2.802,0.396 0.375,0.25 4.438,0.146 4.813,0.396 0.375,0.25 2.521,0.188 2.792,0.396 0.271,0.208 10 false z19 4.51,0.188 4.969,0.385 0.458,0.198 10 false J12

a.

Disconnect the J12 outer mirror control ECU assembly RH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition

*1: for LHD

*2: for RHD

J12-5 (SIG) - J12-7 (GND) G - W-B Power source Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
J12-6 (CPUB) - J12-7 (GND) L - W-B Power source Always 11 to 14 V
J12-14 (BDR) - J12-7 (GND) G - W-B*1
R - W-B*2
Power source Always 11 to 14 V
J12-7 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the J12 outer mirror control ECU assembly RH connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
z19-3 (MR) - Body ground SB - Body ground Power retract mirror motor drive voltage
·

Ignition switch ACC

·

Outer rear view mirror assembly being retracted


11 to 14 V
·

Ignition switch ACC

·

Outer rear view mirror assembly stopped


Below 1 V
z19-11 (MF) - Body ground LG - Body ground Power retract mirror motor drive voltage
·

Ignition switch ACC

·

Outer rear view mirror assembly returning


11 to 14 V
·

Ignition switch ACC

·

Outer rear view mirror assembly stopped


Below 1 V
z19-1 (MV) - Body ground V - Body ground Mirror motor drive voltage
·

Ignition switch ACC

·

Mirror surface stopped


Below 1 V
·

Ignition switch ACC

·

Mirror surface moving downward or left


Below 1 V
·

Ignition switch ACC

·

Mirror surface moving upward


11 to 14 V
z19-9 (MH) - Body ground BR - Body ground Mirror motor drive voltage
·

Ignition switch ACC

·

Mirror surface stopped


Below 1 V
·

Ignition switch ACC

·

Mirror surface moving upward or right


Below 1 V
·

Ignition switch ACC

·

Mirror surface moving left


11 to 14 V
z19-10 (M+) - Body ground R - Body ground Mirror motor drive voltage
·

Ignition switch ACC

·

Mirror surface stopped


Below 1 V
·

Ignition switch ACC

·

Mirror surface moving upward or left


Below 1 V
·

Ignition switch ACC

·

Mirror surface moving downward or right


11 to 14 V
z19-4 (HTR+) - z19-12 (HTR-)* B - W Mirror heater drive voltage
·

Ignition switch ON

·

Rear window defogger switch (mirror heater switch) on


11 to 14 V
·

Ignition switch ON

·

Rear window defogger switch (mirror heater switch) off


Below 1 V
z19-5 (VDD) - z19-14 (GND) R-W - GR Mirror position sensor power supply Ignition switch ON 4.75 to 5.25 V
Ignition switch off Below 1 V
z19-6 (VSSR) - Body ground Y-B - Body ground Vertical direction position sensor signal
·

Ignition switch ACC

·

Mirror surface moving upward or downward


Changes within range of 0 to 5 V
z19-13 (HSSR) - Body ground P - Body ground Horizontal direction position sensor signal
·

Ignition switch ACC

·

Mirror surface moving left or right


Changes within range of 0 to 5 V

*: w/ Mirror Heater




CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND DRIVER SIDE JUNCTION BLOCK ASSEMBLY


E373864C04
3.271,7.844 3.781,8.083 0.51,0.24 4.583,6.177 5.094,6.417 0.51,0.24 1.469,6.177 1.979,6.417 0.51,0.24 1.271,4.677 1.781,4.917 0.51,0.24 3.708,4.469 4.219,4.708 0.51,0.24 5.24,4.469 5.75,4.708 0.51,0.24 6.26,4.448 6.771,4.688 0.51,0.24 5.583,3.094 6.094,3.333 0.51,0.24 3.49,3.083 4,3.323 0.51,0.24 1.271,3.135 1.781,3.375 0.51,0.24 1.271,4.354 1.781,4.594 0.51,0.24 1.604,0.646 1.604,0.417 1.604,0.417 1.76,0.417 false 0.615,1.302 0.948,1.302 true 1.625,1.156 1.958,1.156 true 1.635,1.469 1.969,1.469 true 1.646,1.833 1.979,1.833 true 1.823,0.292 2.135,0.49 0.313,0.198 10 false *1 0.125,0.125 0.51,0.385 0.385,0.26 12 false *A 0.229,1.188 0.615,1.563 0.385,0.375 10 false 2Q*B 2P*C 0.854,1.792 1.24,2.167 0.385,0.375 10 false 2M 0.896,2.229 1.281,2.604 0.385,0.375 10 false 2K 0.917,2.448 1.302,2.823 0.385,0.375 10 false 2L 3.781,0.969 4.167,1.344 0.385,0.375 10 false A 5.844,1.094 6.229,1.469 0.385,0.375 10 false 2N 5.844,1.76 6.229,2.135 0.385,0.375 10 false 2O 3.469,7.875 3.854,8.25 0.385,0.375 10 false A 6.427,4.479 6.813,4.854 0.385,0.375 10 false 2L 5.406,4.49 5.792,4.865 0.385,0.375 10 false 2K 3.854,4.49 4.24,4.865 0.385,0.375 10 false 2M 1.427,4.375 1.813,4.75 0.385,0.375 10 false 2Q 1.438,4.698 1.823,5.073 0.385,0.375 10 false 2P 1.854,4.698 2.24,5.073 0.385,0.375 10 false *C 1.854,4.396 2.24,4.771 0.385,0.375 10 false *A 1.615,6.208 2,6.583 0.385,0.375 10 false 2N 4.74,6.198 5.125,6.573 0.385,0.375 10 false 2O 2.01,1.698 2.552,2 0.542,0.302 10 false G216 1.344,3.156 1.885,3.458 0.542,0.302 10 false G216 2.021,1.031 2.563,1.333 0.542,0.302 10 false G217 5.667,3.115 6.208,3.417 0.542,0.302 10 false G217 3.583,3.104 4.125,3.406 0.542,0.302 10 false G218 2.01,1.354 2.552,1.656 0.542,0.302 10 false G218
*A Main Body ECU (Multiplex Network Body ECU) with 3 connectors *B for LHD
*C for RHD - -
*1 Main Body ECU (Multiplex Network Body ECU) - -


a.

Remove the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A-32 (IG) - Body ground None - Body ground Ignition power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
A-31 (BECU) - Body ground None - Body ground Battery power supply Always 11 to 14 V
A-30 (ACC) - Body ground None - Body ground ACC power supply Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
A-11 (GND1) - Body ground None - Body ground Ground Always Below 1 Ω


c.

Install the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION


d.

Measure the voltage and pulse according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G217-4 (MIRB) - G217-6 (MIRE) R - L Mirror surface adjust switch signal
·

Ignition switch ACC

·

Mirror surface adjust switch up


Below 1.7 V
·

Ignition switch ACC

·

Mirror surface adjust switch right


Below 2.7 V
·

Ignition switch ACC

·

Mirror surface adjust switch down


Below 3.5 V
·

Ignition switch ACC

·

Mirror surface adjust switch left


Below 4 V
·

Ignition switch ACC

·

Mirror surface adjust switch off


3.8 to 5 V
G217-5 (MIRS) - G217-6 (MIRE) P - L Mirror select switch signal
·

Ignition switch ACC

·

Mirror select switch L


Below 2 V
·

Ignition switch ACC

·

Mirror select switch R


Below 1 V
·

Ignition switch ACC

·

Mirror select switch off


3.8 to 5 V
G216-14 (RET) - Body ground W - Body ground Mirror retract switch signal
·

Ignition switch ACC

·

Mirror retract switch not in return position


Pulse generation (See waveform 1 or 2)
·

Ignition switch ACC

·

Mirror retract switch in return position


Below 1 V
G216-11 (AMR) - Body ground V - Body ground Mirror retract switch signal
·

Ignition switch ACC

·

Mirror retract switch not in retract position


Pulse generation (See waveform 1 or 2)
·

Ignition switch ACC

·

Mirror retract switch in retract position


Below 1 V
G217-13 (M1) - Body ground*3 SB - Body ground Seat memory switch M1 signal
·

Ignition switch ON

·

Seat memory switch M1 off


Pulse generation (See waveform 3 or 4)
·

Ignition switch ON

·

Seat memory switch M1 on


Below 1 V
G217-14 (M2) - Body ground*3 V - Body ground Seat memory switch M2 signal
·

Ignition switch ON

·

Seat memory switch M2 off


Pulse generation (See waveform 3 or 4)
·

Ignition switch ON

·

Seat memory switch M2 on


Below 1 V
G217-16 (MM) - Body ground*3 LG - Body ground Seat memory switch SET signal
·

Ignition switch ON

·

Seat memory switch SET off


Pulse generation (See waveform 3 or 4)
·

Ignition switch ON

·

Seat memory switch SET on


Below 1 V

*1: for LHD

*2: for RHD

*3: w/ Memory


e.
B244640E02
0.135,1.198 0.594,1.396 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 1.

Waveform 1 (Reference)
Item Content
Terminal No. (Symbol) G216-14 (RET) or G216-11 (AMR) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition
·

Ignition switch ACC

·

Mirror retract switch not in retract position




f.
B244641E02
0.135,0.979 0.594,1.177 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 2.

Waveform 2 (Reference)
Item Content
Terminal No. (Symbol) G216-14 (RET) or G216-11 (AMR) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition
·

Ignition switch ACC

·

Mirror retract switch not in retract position




g.
B244640E02
0.135,1.198 0.594,1.396 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 3.

Waveform 3 (Reference)
Item Content
Terminal No. (Symbol) G217-13 (M1) - Body ground
G217-14 (M2) - Body ground
G217-16 (MM) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition
·

Ignition switch ON

·

Seat memory switch M1 off

·

Seat memory switch M2 off

·

Seat memory switch SET off




h.
B244641E02
0.135,0.979 0.594,1.177 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 4.

Waveform 4 (Reference)
Item Content
Terminal No. (Symbol) G217-13 (M1) - Body ground
G217-14 (M2) - Body ground
G217-16 (MM) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition
·

Ignition switch ON

·

Seat memory switch M1 off

·

Seat memory switch M2 off

·

Seat memory switch SET off