Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster) › from 2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260911 VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster)  Downhill Assist Control Indicator Light does not Come ON  


DESCRIPTION

Even if the downhill assist control switch is pressed, the downhill assist control indicator light blinks and downhill assist control does not activate under the following conditions:

·

The transfer is in H4.

·

The brake system is malfunctioning.

·

The temperature of the hydraulic brake booster increases and downhill assist control is temporarily canceled.


WIRING DIAGRAM

C216836E11
3.073,1.813 5.156,2.188 2.083,0.375 10 false Downhill Assist Control Switch (Combination Switch Assembly)*1 5.344,2.063 6.917,2.49 1.573,0.427 10 false Master Cylinder Solenoid (Skid Control ECU) 0.958,3.292 3.125,3.479 2.167,0.188 10 false : CAN Communication System 0.521,2.865 2.469,3.156 1.948,0.292 10 false Combination Meter Assembly 0.677,2.042 1.813,2.219 1.135,0.177 10 false Downhill Assist 1.219,0.927 1.448,1.115 0.229,0.188 10 false IG 5.76,1.198 6.229,1.365 0.469,0.167 10 false HZRI 4.281,1.073 4.594,1.292 0.313,0.219 10 false +B2 5.375,1.906 5.594,2.063 0.219,0.156 10 false A7 4.698,1.104 4.938,1.271 0.24,0.167 10 false 5 3.354,1.073 3.49,1.24 0.135,0.167 10 false 2 3.052,1.656 4.094,1.844 1.042,0.188 10 false G306*1, G232*2 0.542,2.698 0.99,2.896 0.448,0.198 10 false G304 3.094,2.542 5.229,2.927 2.135,0.385 10 false Downhill assist Control switch*2 3.615,1.073 3.927,1.292 0.313,0.219 10 false E 2.99,3.125 5.354,3.313 2.365,0.188 10 false *1: w/ Combination Switch Assembly 3,3.417 5.365,3.604 2.365,0.188 10 false *2: w/o Combination Switch Assembly 5.406,1.104 5.646,1.271 0.24,0.167 10 false 28

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (master cylinder solenoid), perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>CALIBRATION).


PROCEDURE

2.CHECK FOR DTC
a.

Check for DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output (w/ Combination Switch Assembly) A
DTC is not output (w/o Combination Switch Assembly) B
DTC is output C



A

3.INSPECT COMBINATION SWITCH ASSEMBLY

B

4.INSPECT DOWNHILL ASSIST CONTROL SWITCH

C

3.INSPECT COMBINATION SWITCH ASSEMBLY
a.

Remove the downhill assist control switch (combination switch assembly) (See pageBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>CRAWL SWITCH>REMOVAL).


b.
C381450E02
1.177,1.958 1.344,1.958 1.344,1.958 1.344,1.292 true 2.198,1.948 2.031,1.948 2.031,1.948 2.031,1.281 true 0.833,1.854 1.292,2.073 0.458,0.219 10 false +B2 2.271,1.844 2.615,2.063 0.344,0.219 10 false E 0.177,0.125 0.521,0.344 0.344,0.219 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
2 - 5 Not pushed in 10 kΩ or higher
Pushed in Below 1 Ω


Text in Illustration
*a Component without harness connected
(Downhill Assist Control Switch (Combination Switch Assembly))



OK

5.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID HZRI CIRCUIT)

NG

REPLACE COMBINATION SWITCH ASSEMBLY

4.INSPECT DOWNHILL ASSIST CONTROL SWITCH
a.

Remove the downhill assist control switch (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>DOWNHILL ASSIST CONTROL SWITCH>REMOVAL).


b.
C381450E02
1.177,1.958 1.344,1.958 1.344,1.958 1.344,1.292 true 2.198,1.948 2.031,1.948 2.031,1.948 2.031,1.281 true 0.833,1.854 1.292,2.073 0.458,0.219 10 false +B2 2.271,1.844 2.615,2.063 0.344,0.219 10 false E 0.177,0.125 0.521,0.344 0.344,0.219 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
2 - 5 Not pushed in 10 kΩ or higher
Pushed in Below 1 Ω


Text in Illustration
*a Component without harness connected
(Downhill Assist Control Switch)



OK

5.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID HZRI CIRCUIT)

NG

5.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID HZRI CIRCUIT)
a.

Disconnect the A7 skid control ECU (master cylinder solenoid) connector.


b.

w/ Combination Switch Assembly:

Disconnect the G306 downhill assist control switch connector.


c.

w/o Combination Switch Assembly:

Disconnect the G232 downhill assist control switch connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Combination Switch Assembly
Tester Connection Condition Specified Condition
A7-28 (HZRI) - G306-5 (+B2) Always Below 1 Ω
A7-28 (HZRI) or G306-5 (+B2) - Body ground Always 10 kΩ or higher
G306-2 (E) - Body ground Always Below 1 Ω

w/o Combination Switch Assembly
Tester Connection Condition Specified Condition
A7-28 (HZRI) - G232-5 (+B2) Always Below 1 Ω
A7-28 (HZRI) or G232-5 (+B2) - Body ground Always 10 kΩ or higher
G232-2 (E) - Body ground Always Below 1 Ω




OK

6.PERFORM ACTIVE TEST USING GTS (DOWNHILL ASSIST CONTROL LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.PERFORM ACTIVE TEST USING GTS (DOWNHILL ASSIST CONTROL LIGHT)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
Downhill Assist Control Light Downhill assist control indicator light Indicator light ON/OFF Observe the combination meter.


f.

When performing the Downhill Assist Control Light Active Test, check Downhill Assist Control Light in the Data List.

(See pageBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>DATA LIST / ACTIVE TEST)

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Downhill Assist Control Light Downhill assist control indicator light/ ON or OFF ON: Indicator light on
OFF: Indicator light off
-

Result
Result Proceed to
Data List Display Data List Display when Performing Active Test ON/OFF Operation
ON Changes between ON and OFF A
Does not change between ON and OFF (for LHD) B
Does not change between ON and OFF (for RHD) C
OFF Changes between ON and OFF A
Does not change between ON and OFF (for LHD) B
Does not change between ON and OFF (for RHD) C



A

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

B

C