If any of the following is detected, the ABS warning light remains on.
The skid control ECU connector is disconnected from the skid control ECU.
There is a malfunction in the skid control ECU internal circuit.
There is an open in the harness between the combination meter and skid control ECU.
The anti-lock brake system is defective.
The voltage at terminal IG1 is high.
The rear differential is locked.*
*: w/ Rear Differential Lock
It may not be possible to use the GTS when the skid control ECU is abnormal.
When replacing the master cylinder solenoid, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>CALIBRATION).
Check the skid control ECU connector connection.
The 2 connectors are securely connected.
OK
NG
Check for DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC is output | B |
A
B
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus (w/ Central Gateway ECU: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM, w/o Central Gateway ECU: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).
CAN Bus Check indicates no malfunctions in CAN communication.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/ Central Gateway ECU) | B |
| NG (w/o Central Gateway ECU) | C |
A
B
C
OK
NG
Disconnect the A7 skid control ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A7-40 (EXI3) - Body ground | Ignition switch ON
w/ Rear Differential Lock: Rear differential free |
11 to 14 V |
| *a | Front view of wire harness connector
(to Skid Control ECU (Master Cylinder Solenoid)) |
OK
NG
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| ABS Warning Light | ABS warning light/ ON or OFF | OFF | - |
When performing the ABS Warning Light Active Test, check ABS Warning Light in the Data List.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| ABS Warning Light | ABS warning light | Warning light ON/OFF | Observe the combination meter. |
| Result | Proceed to | |
|---|---|---|
| Data List Display | Data List Display when Performing Active Test ON/OFF Operation | |
| ON | Changes between ON and OFF | A |
| Does not change between ON and OFF (for LHD) | B | |
| Does not change between ON and OFF (for RHD) | C | |
| OFF | Changes between ON and OFF | A |
| Does not change between ON and OFF (for LHD) | B | |
| Does not change between ON and OFF (for RHD) | C | |
A
(See pageVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
B
C
OK
NG
Disconnect the A7 and A8 skid control ECU connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A7-1 (GND1) - Body ground | Always | Below 1 Ω |
| A7-32 (GND2) - Body ground | Always | Below 1 Ω |
| A8-4 (GND3) - Body ground | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| NG | A |
| OK (for LHD) | B |
| OK (for RHD) | C |
A
B
C
Disconnect the A7 skid control ECU connector.
Disconnect the G53 4 wheel drive control ECU connector.
w/ Rear Differential Lock:
Disconnect the E2 rear differential lock detection switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A7-40 (EXI3) - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK (w/o Rear Differential Lock) | A |
| OK (w/ Rear Differential Lock) | B |
| NG | C |
A
B
C
Disconnect the A7 skid control ECU connector.
Connect the G53 4 wheel drive control ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A7-40 (EXI3) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector
(to Skid Control ECU (Master Cylinder Solenoid)) |
| Result | Proceed to |
|---|---|
| NG | A |
| OK (for LHD) | B |
| OK (for RHD) | C |
A
B
C
Remove the rear differential lock detection switch (See page Drivetrain>AXLE AND DIFFERENTIAL>REAR DIFFERENTIAL LOCK POSITION SWITCH>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 1 (GND) - 2 (+B) | Pushed in | Below 1 Ω |
| Not pushed in | 10 kΩ or higher |
| *a | Component without harness connected
(Rear Differential Lock Detection Switch) |
OK
NG
Disconnect the A7 skid control ECU connector.
Connect the G53 4 wheel drive control ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A7-40 (EXI3) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector
(to Skid Control ECU (Master Cylinder Solenoid)) |
| Result | Proceed to |
|---|---|
| NG | A |
| OK (for LHD) | B |
| OK (for RHD) | C |
A
B
C