Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › from 2017.08
RM27T0E _59 Vehicle Exterior _053742 WINDOW / GLASS _0261225 POWER WINDOW CONTROL SYSTEM Y

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use these procedures to troubleshoot the power window control system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
HINT:
·

In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.

·

Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.

·

The following 5 items are important points for problem analysis:

What Vehicle model, system name
When Date, time, occurrence frequency
Where Road conditions
Under what conditions? Driving conditions, weather conditions
How did it happen? Problem symptoms



Result:
Proceed to
NEXT



NEXT

3.INSPECT BATTERY VOLTAGE
3.INSPECT BATTERY VOLTAGE
a.

Measure the battery voltage.

Standard voltage:

11 to 14 V


HINT:
·

A simple method to determine whether the battery is discharged is to operate the horn.

·

If the voltage is below 11 V, recharge or replace the battery before proceeding.




b.

Check the fuses and relays.


c.

Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.


Result:
Proceed to
NEXT



NEXT

4.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
4.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*

Result:
Result Proceed to
CAN DTC is not output A
CAN DTC is output (w/ Central Gateway ECU) B
CAN DTC is output (w/o Central Gateway ECU) C



A

5.CHECK COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*

B

C

5.CHECK COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*
a.

Using the GTS, check for LIN communication system DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR


Result:
Result Proceed to
LIN DTC is not output A
LIN DTC is output B



A

6.CHECK FOR DTC*

B

6.CHECK FOR DTC*
a.

Check for DTCs and make a note of any codes that are output.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DTC CHECK / CLEAR




Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

7.PROBLEM SYMPTOMS TABLE

B

7.PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault not listed in problem symptoms table A
Fault listed in problem symptoms table B



A

8.OVERALL ANALYSIS AND TROUBLESHOOTING*

B

ADJUST, REPAIR OR REPLACE IN ACCORDANCE WITH PROBLEM SYMPTOMS TABLE

8.OVERALL ANALYSIS AND TROUBLESHOOTING*

NEXT

9.ADJUST, REPAIR OR REPLACE
9.ADJUST, REPAIR OR REPLACE
a.

Check if any of the door window regulators, power window regulator motor assemblies, door glass or door glass runs have been removed and reinstalled.


Result:
Result Proceed to
Any of the door window regulators, power window regulator motor assemblies, door glass or door glass runs have been removed and reinstalled. A
The door window regulators, power window regulator motor assemblies, door glass or door glass runs have not been removed and reinstalled. B



A

10.INITIALIZE POWER WINDOW CONTROL SYSTEM

B

11.CONFIRMATION TEST
10.INITIALIZE POWER WINDOW CONTROL SYSTEM
a.

Initialize the power window control system.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

11.CONFIRMATION TEST
11.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END