Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › from 2017.08
RM27T0E _59 Vehicle Exterior _053742 WINDOW / GLASS _0261225 POWER WINDOW CONTROL SYSTEM U

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  TERMINALS OF ECU  


CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY


U169632E02
4.052,0.167 4.323,0.375 0.271,0.208 10 false J9 2.927,0.167 3.188,0.344 0.26,0.177 10 false K4 3.229,0.167 3.5,0.354 0.271,0.188 10 false *A 4.344,0.167 4.615,0.365 0.271,0.198 10 false *B

Text in Illustration
*A for LHD *B for RHD

*1: for LHD

*2: for RHD


a.

Disconnect the K4*1 or J9*2 multiplex network master switch connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K4-11 (B) - K4-12 (GND) L - W-B Power supply Always 11 to 14 V
K4-12 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

for RHD:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J9-11 (B) - J9-12 (GND) L - W-B Power supply Always 11 to 14 V
J9-12 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the K4*1 or J9*2 multiplex network master switch connector.


d.

Measure the voltage according to the value(s) in the table below.

for LHD:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K4-15 (DOWN) - K4-12 (GND) LA-B - W-B Power window motor down input Ignition switch ON, driver side power window regulator switch off 11 to 14 V
K4-15 (DOWN) - K4-12 (GND) LA-B - W-B Power window motor down input Ignition switch ON, driver side power window switch down (Manual operation) Below 1 V
K4-18 (LED) - K4-12 (GND) LA-V - W-B LED illumination signal Ignition switch ON 11 to 14 V
K4-18 (LED) - K4-12 (GND) LA-V - W-B LED illumination signal Ignition switch off Below 1 V
K4-20 (UP) - K4-12 (GND) LA-P - W-B Power window motor up input Ignition switch ON, driver side power window switch off 11 to 14 V
K4-20 (UP) - K4-12 (GND) LA-P - W-B Power window motor up input Ignition switch ON, driver side power window switch up (Manual operation) Below 1 V

for RHD:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J9-15 (DOWN) - J9-12 (GND) LA-B - W-B Power window motor down input Ignition switch ON, driver side power window regulator switch off 11 to 14 V
J9-15 (DOWN) - J9-12 (GND) LA-B - W-B Power window motor down input Ignition switch ON, driver side power window switch down (Manual operation) Below 1 V
J9-18 (LED) - J9-12 (GND) LA-V - W-B LED illumination signal Ignition switch ON 11 to 14 V
J9-18 (LED) - J9-12 (GND) LA-V - W-B LED illumination signal Ignition switch off Below 1 V
J9-20 (UP) - J9-12 (GND) LA-P - W-B Power window motor up input Ignition switch ON, driver side power window switch off 11 to 14 V
J9-20 (UP) - J9-12 (GND) LA-P - W-B Power window motor up input Ignition switch ON, driver side power window switch up (Manual operation) Below 1 V



CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY


U169784E02
3.063,0.229 3.333,0.417 0.271,0.188 10 false J1 3.708,0.24 4.094,0.406 0.385,0.167 10 false K10 3.323,0.229 3.604,0.417 0.281,0.188 10 false *A 4.021,0.24 4.313,0.427 0.292,0.188 10 false *B

Text in Illustration
*A for LHD *B for RHD

*1: for LHD

*2: for RHD


a.

Disconnect the J1*1 or K10*2 power window regulator switch connector.


b.

Measure the resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J1-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

for RHD:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K10-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the J1*1 or K10*2 power window regulator switch connector.


d.

Measure the voltage according to the value(s) in the table below.

for LHD:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J1-6 (UP) - J1-1 (GND) L - W-B Power window motor up input Ignition switch ON, power window regulator switch off 11 to 14 V
J1-6 (UP) - J1-1 (GND) L - W-B Power window motor up input Ignition switch ON, power window regulator switch up Below 1 V
J1-8 (AUTO) - J1-1 (GND) P - W-B Power window motor auto up or down input Ignition switch ON, door glass fully open 11 to 14 V
J1-8 (AUTO) - J1-1 (GND) P - W-B Power window motor auto up or down input Ignition switch ON, power window auto up or down function operating Below 1 V
J1-8 (AUTO) - J1-1 (GND) P - W-B Power window motor auto up or down input Ignition switch ON, door glass fully closed 11 to 14 V
J1-4 (LED) - J1-1 (GND) V - W-B LED illumination signal Ignition switch ON 11 to 14 V
J1-4 (LED) - J1-1 (GND) V - W-B LED illumination signal Ignition switch off Below 1 V
J1-7 (DOWN) - J1-1 (GND) B - W-B Power window motor down input Ignition switch ON, power window regulator switch off 11 to 14 V
J1-7 (DOWN) - J1-1 (GND) B - W-B Power window motor down input Ignition switch ON, power window regulator switch down Below 1 V

for RHD:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K10-6 (UP) - K10-1 (GND) L - W-B Power window motor up input Ignition switch ON, power window regulator switch off 11 to 14 V
K10-6 (UP) - K10-1 (GND) L - W-B Power window motor up input Ignition switch ON, power window regulator switch up Below 1 V
K10-8 (AUTO) - K10-1 (GND) P - W-B Power window motor auto up or down input Ignition switch ON, door glass fully open 11 to 14 V
K10-8 (AUTO) - K10-1 (GND) P - W-B Power window motor auto up or down input Ignition switch ON, power window auto up or down function operating Below 1 V
K10-8 (AUTO) - K10-1 (GND) P - W-B Power window motor auto up or down input Ignition switch ON, door glass fully closed 11 to 14 V
K10-4 (LED) - K10-1 (GND) V - W-B LED illumination signal Ignition switch ON 11 to 14 V
K10-4 (LED) - K10-1 (GND) V - W-B LED illumination signal Ignition switch off Below 1 V
K10-7 (DOWN) - K10-1 (GND) B - W-B Power window motor down input Ignition switch ON, power window regulator switch off 11 to 14 V
K10-7 (DOWN) - K10-1 (GND) B - W-B Power window motor down input Ignition switch ON, power window regulator switch down Below 1 V



CHECK REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH (for 5 Door)


U148042E03
3.448,0.24 3.75,0.417 0.302,0.177 10 false M2

a.

Disconnect the M2 rear power window regulator switch connector.


b.

Measure the resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M2-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the M2 rear power window regulator switch connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M2-6 (UP) - M2-1 (GND) L - W-B Power window motor up input Ignition switch ON, power window regulator switch off 11 to 14 V
M2-6 (UP) - M2-1 (GND) L - W-B Power window motor up input Ignition switch ON, power window regulator switch up Below 1 V
M2-8 (AUTO) - M2-1 (GND) P - W-B Power window motor auto up or down input Ignition switch ON, door glass fully open 11 to 14 V
M2-8 (AUTO) - M2-1 (GND) P - W-B Power window motor auto up or down input Ignition switch ON, power window auto up or down function operating Below 1 V
M2-8 (AUTO) - M2-1 (GND) P - W-B Power window motor auto up or down input Ignition switch ON, door glass fully closed 11 to 14 V
M2-4 (LED) - M2-1 (GND) V - W-B LED illumination signal Ignition switch ON 11 to 14 V
M2-4 (LED) - M2-1 (GND) V - W-B LED illumination signal Ignition switch off Below 1 V
M2-7 (DOWN) - M2-1 (GND) B - W-B Power window motor down input Ignition switch ON, power window regulator switch off 11 to 14 V
M2-7 (DOWN) - M2-1 (GND) B - W-B Power window motor down input Ignition switch ON, power window regulator switch down Below 1 V



CHECK REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH (for 5 Door)


U148043E03
3.479,0.24 3.771,0.406 0.292,0.167 10 false L2

a.

Disconnect the L2 rear power window regulator switch connector.


b.

Measure the resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L2-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the L2 rear power window regulator switch connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L2-6 (UP) - L2-1 (GND) L - W-B Power window motor up input Ignition switch ON, power window regulator switch off 11 to 14 V
L2-6 (UP) - L2-1 (GND) L - W-B Power window motor up input Ignition switch ON, power window regulator switch up Below 1 V
L2-8 (AUTO) - L2-1 (GND) P - W-B Power window motor auto up or down input Ignition switch ON, door glass fully open 11 to 14 V
L2-8 (AUTO) - L2-1 (GND) P - W-B Power window motor auto up or down input Ignition switch ON, power window auto up or down function operating Below 1 V
L2-8 (AUTO) - L2-1 (GND) P - W-B Power window motor auto up or down input Ignition switch ON, door glass fully closed 11 to 14 V
L2-4 (LED) - L2-1 (GND) V - W-B LED illumination signal Ignition switch ON 11 to 14 V
L2-4 (LED) - L2-1 (GND) V - W-B LED illumination signal Ignition switch off Below 1 V
L2-7 (DOWN) - L2-1 (GND) B - W-B Power window motor down input Ignition switch ON, power window regulator switch off 11 to 14 V
L2-7 (DOWN) - L2-1 (GND) B - W-B Power window motor down input Ignition switch ON, power window regulator switch down Below 1 V



CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


U148035E03
3.49,0.26 3.771,0.438 0.281,0.177 10 false K7

*1: for LHD

*2: for RHD


a.

Disconnect the K7 power window regulator motor connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K7-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
K7-2 (B) - Body ground R - Body ground*1
G - Body ground*2
Battery power supply Always 11 to 14 V


c.

Reconnect the K7 power window regulator motor connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K7-5 (LED) - K7-1 (GND) LA-V - W-B*1
V - W-B*2
LED illumination signal Ignition switch ON 11 to 14 V
K7-5 (LED) - K7-1 (GND) LA-V - W-B*1
V - W-B*2
LED illumination signal Ignition switch off Below 1 V
K7-7 (DOWN) - K7-1 (GND) LA-B - W-B*1
B - W-B*2
Power window motor down output Ignition switch ON, power window regulator master switch off 11 to 14 V
K7-7 (DOWN) - K7-1 (GND) LA-B - W-B*1
B - W-B*2
Power window motor down output Ignition switch ON, power window regulator master switch down Below 1 V
K7-7 (DOWN) - K7-1 (GND) LA-B - W-B*1
B - W-B*2
Power window motor down output Ignition switch ON, door glass fully closed 11 to 14 V
K7-7 (DOWN) - K7-1 (GND) LA-B - W-B*1
B - W-B*2
Power window motor down output Ignition switch ON, power window auto down function operating Below 1 V
K7-7 (DOWN) - K7-1 (GND) LA-B - W-B*1
B - W-B*2
Power window motor down output Ignition switch ON, door glass fully open 11 to 14 V
K7-10 (UP) - K7-1 (GND) LA-P - W-B*1
L - W-B*2
Power window motor up output Ignition switch ON, power window regulator master switch off 11 to 14 V
K7-10 (UP) - K7-1 (GND) LA-P - W-B*1
L - W-B*2
Power window motor up output Ignition switch ON, power window regulator master switch up Below 1 V
K7-10 (UP) - K7-1 (GND) LA-P - W-B*1
L - W-B*2
Power window motor up output Ignition switch ON, door glass fully open 11 to 14 V
K7-10 (UP) - K7-1 (GND) LA-P - W-B*1
L - W-B*2
Power window motor up output Ignition switch ON, power window auto up function operating Below 1 V
K7-10 (UP) - K7-1 (GND) LA-P - W-B*1
L - W-B*2
Power window motor up output Ignition switch ON, door glass fully closed 11 to 14 V



CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH


U148036E03
3.49,0.26 3.76,0.417 0.271,0.156 10 false J7

*1: for LHD

*2: for RHD


a.

Disconnect the J7 power window regulator motor connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J7-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
J7-2 (B) - Body ground G - Body ground*1
R - Body ground*2
Battery power supply Always 11 to 14 V


c.

Reconnect the J7 power window regulator motor connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J7-5 (LED) - J7-1 (GND) V - W-B*1
LA-V - W-B*2
LED illumination signal Ignition switch ON 11 to 14 V
J7-5 (LED) - J7-1 (GND) V - W-B*1
LA-V - W-B*2
LED illumination signal Ignition switch off Below 1 V
J7-7 (DOWN) - J7-1 (GND) B - W-B*1
LA-B - W-B*2
Power window motor down output Ignition switch ON, power window regulator switch off 11 to 14 V
J7-7 (DOWN) - J7-1 (GND) B - W-B*1
LA-B - W-B*2
Power window motor down output Ignition switch ON, power window regulator switch down Below 1 V
J7-7 (DOWN) - J7-1 (GND) B - W-B*1
LA-B - W-B*2
Power window motor down output Ignition switch ON, door glass fully closed 11 to 14 V
J7-7 (DOWN) - J7-1 (GND) B - W-B*1
LA-B - W-B*2
Power window motor down output Ignition switch ON, power window auto down function operating Below 1 V
J7-7 (DOWN) - J7-1 (GND) B - W-B*1
LA-B - W-B*2
Power window motor down output Ignition switch ON, door glass fully open 11 to 14 V
J7-10 (UP) - J7-1 (GND) L - W-B*1
LA-P - W-B*2
Power window motor up output Ignition switch ON, power window regulator switch off 11 to 14 V
J7-10 (UP) - J7-1 (GND) L - W-B*1
LA-P - W-B*2
Power window motor up output Ignition switch ON, power window regulator switch up Below 1 V
J7-10 (UP) - J7-1 (GND) L - W-B*1
LA-P - W-B*2
Power window motor up output Ignition switch ON, door glass fully open 11 to 14 V
J7-10 (UP) - J7-1 (GND) L - W-B*1
LA-P - W-B*2
Power window motor up output Ignition switch ON, power window auto up function operating Below 1 V
J7-10 (UP) - J7-1 (GND) L - W-B*1
LA-P - W-B*2
Power window motor up output Ignition switch ON, door glass fully closed 11 to 14 V



CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for 5 Door)


U115619E04
3.469,0.26 3.802,0.427 0.333,0.167 10 false M4

a.

Disconnect the M4 rear power window regulator motor connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M4-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
M4-2 (B) - Body ground W - Body ground Battery power supply Always 11 to 14 V


c.

Reconnect the M4 rear power window regulator motor connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M4-5 (LED) - M4-1 (GND) V - W-B LED illumination signal Ignition switch ON 11 to 14 V
M4-5 (LED) - M4-1 (GND) V - W-B LED illumination signal Ignition switch off Below 1 V
M4-7 (DOWN) - M4-1 (GND) B - W-B Power window motor down input Ignition switch ON, power window regulator switch off 11 to 14 V
M4-7 (DOWN) - M4-1 (GND) B - W-B Power window motor down input Ignition switch ON, power window regulator switch down Below 1 V
M4-7 (DOWN) - M4-1 (GND) B - W-B Power window motor down input Ignition switch ON, door glass fully closed 11 to 14 V
M4-7 (DOWN) - M4-1 (GND) B - W-B Power window motor down input Ignition switch ON, power window auto down function operating Below 1 V
M4-7 (DOWN) - M4-1 (GND) B - W-B Power window motor down input Ignition switch ON, door glass fully open 11 to 14 V
M4-10 (UP) - M4-1 (GND) L - W-B Power window motor up output Ignition switch ON, power window regulator switch off 11 to 14 V
M4-10 (UP) - M4-1 (GND) L - W-B Power window motor up output Ignition switch ON, power window regulator switch up Below 1 V
M4-10 (UP) - M4-1 (GND) L - W-B Power window motor up output Ignition switch ON, door glass fully open 11 to 14 V
M4-10 (UP) - M4-1 (GND) L - W-B Power window motor up output Ignition switch ON, power window auto up function operating Below 1 V
M4-10 (UP) - M4-1 (GND) L - W-B Power window motor up output Ignition switch ON, door glass fully closed 11 to 14 V



CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for 5 Door)


U115620E04
3.49,0.26 3.75,0.427 0.26,0.167 10 false L4

a.

Disconnect the L4 rear window regulator motor connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L4-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
L4-2 (B) - Body ground W - Body ground Battery power supply Always 11 to 14 V


c.

Reconnect the L4 rear power window regulator motor connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L4-5 (LED) - L4-1 (GND) V - W-B LED illumination signal Ignition switch ON 11 to 14 V
L4-5 (LED) - L4-1 (GND) V - W-B LED illumination signal Ignition switch off Below 1 V
L4-7 (DOWN) - L4-1 (GND) B - W-B Power window motor down output Ignition switch ON, power window regulator switch off 11 to 14 V
L4-7 (DOWN) - L4-1 (GND) B - W-B Power window motor down output Ignition switch ON, power window regulator switch down Below 1 V
L4-7 (DOWN) - L4-1 (GND) B - W-B Power window motor down output Ignition switch ON, door glass fully closed 11 to 14 V
L4-7 (DOWN) - L4-1 (GND) B - W-B Power window motor down output Ignition switch ON, power window auto down function operating Below 1 V
L4-7 (DOWN) - L4-1 (GND) B - W-B Power window motor down output Ignition switch ON, door glass fully open 11 to 14 V
L4-10 (UP) - L4-1 (GND) L - W-B Power window motor up output Ignition switch ON, power window regulator switch off 11 to 14 V
L4-10 (UP) - L4-1 (GND) L - W-B Power window motor up output Ignition switch ON, power window regulator switch up Below 1 V
L4-10 (UP) - L4-1 (GND) L - W-B Power window motor up output Ignition switch ON, door glass fully open 11 to 14 V
L4-10 (UP) - L4-1 (GND) L - W-B Power window motor up output Ignition switch ON, power window auto up function operating Below 1 V
L4-10 (UP) - L4-1 (GND) L - W-B Power window motor up output Ignition switch ON, door glass fully closed 11 to 14 V



CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (for 5L-E)


E373866C04
1.073,3.354 1.479,3.615 0.406,0.26 3.49,3.365 3.896,3.625 0.406,0.26 5.75,3.292 6.156,3.552 0.406,0.26 0.583,4.698 0.99,4.958 0.406,0.26 1.448,4.698 1.854,4.958 0.406,0.26 3.792,4.677 4.198,4.938 0.406,0.26 5.771,4.74 6.177,5 0.406,0.26 4.781,5.948 5.188,6.208 0.406,0.26 1.74,5.938 2.146,6.198 0.406,0.26 3.344,7.219 3.75,7.479 0.406,0.26 1.615,0.625 1.813,0.406 1.813,0.406 2.01,0.406 false 1.625,1.125 1.823,0.906 1.823,0.906 2.021,0.906 true 1.615,1.458 1.813,1.24 1.813,1.24 2.01,1.24 true 1.625,1.844 1.823,1.625 1.823,1.625 2.021,1.625 true 0.938,1.313 0.76,1.104 0.76,1.104 0.573,1.104 true 2.063,0.333 2.375,0.531 0.313,0.198 10 false *1 3.74,0.969 3.896,1.167 0.156,0.198 10 false A 5.875,1.156 6.188,1.354 0.313,0.198 10 false 2D 5.875,1.823 6.188,2.021 0.313,0.198 10 false 2A 2.063,1.552 2.521,1.75 0.458,0.198 10 false G63 2.063,1.167 2.521,1.365 0.458,0.198 10 false G64 2.063,0.823 2.521,1.021 0.458,0.198 10 false G65 1.167,3.406 1.625,3.604 0.458,0.198 10 false G63 3.563,3.406 4.021,3.604 0.458,0.198 10 false G64 5.813,3.344 6.271,3.542 0.458,0.198 10 false G65 1.063,2.375 1.375,2.573 0.313,0.198 10 false 2K 0.917,1.792 1.229,1.99 0.313,0.198 10 false 2F 0.292,1.031 0.646,1.25 0.354,0.219 10 false 2I*A 0.292,1.208 0.646,1.427 0.354,0.219 10 false 2H*B 3.5,7.271 3.656,7.469 0.156,0.198 10 false A 4.885,5.99 5.198,6.188 0.313,0.198 10 false 2A 5.885,4.771 6.198,4.969 0.313,0.198 10 false 2K 3.927,4.708 4.24,4.906 0.313,0.198 10 false 2F 1.865,5.979 2.177,6.177 0.313,0.198 10 false 2D 0.75,4.75 1.063,4.948 0.313,0.198 10 false 2I 1.563,4.74 1.875,4.938 0.313,0.198 10 false 2H 1.042,4.74 1.354,4.938 0.313,0.198 10 false *A 1.927,4.729 2.24,4.927 0.313,0.198 10 false *B
*A for LHD *B for RHD
*1 Main Body ECU (Multiplex Network Body ECU) - -


a.

Remove the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A-30 (BECU) - Body ground - Battery power supply Always 11 to 14 V
A-31 (ALTB) - Body ground - Battery power supply Always 11 to 14 V
A-32 (IG) - Body ground - Ignition switch power supply Ignition switch ON 11 to 14 V
A-32 (IG) - Body ground - Ignition switch power supply Ignition switch off Below 1 V
A-29 (ACC) - Body ground - ACC power supply Ignition switch ACC 11 to 14 V
A-29 (ACC) - Body ground - ACC power supply Ignition switch off Below 1 V
A-11 (GND1) - Body ground - Ground Always Below 1 Ω
G63-3 (GND2) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Install the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION


d.

Measure the voltage according to the value(s) in the table below.

for LHD:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
2I-27 (FLCY) - Body ground R - Body ground Front door LH courtesy switch input Front door LH open Below 1 V
2I-27 (FLCY) - Body ground R - Body ground Front door LH courtesy switch input Front door LH closed 11 to 14 V
2D-15 (FRCY) - Body ground B - Body ground Front door RH courtesy switch input Front door RH open Below 1 V
2D-15 (FRCY) - Body ground B - Body ground Front door RH courtesy switch input Front door RH closed 11 to 14 V

for RHD:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
2D-31 (FLCY) - Body ground R - Body ground Front door LH courtesy switch input Front door LH open Below 1 V
2D-31 (FLCY) - Body ground R - Body ground Front door LH courtesy switch input Front door LH closed 11 to 14 V
2H-26 (FRCY) - Body ground B - Body ground Front door RH courtesy switch input Front door RH open Below 1 V
2H-26 (FRCY) - Body ground B - Body ground Front door RH courtesy switch input Front door RH closed 11 to 14 V



CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (except 5L-E)


E373864C06
1.25,3.167 1.677,3.406 0.427,0.24 3.552,3.156 3.979,3.396 0.427,0.24 5.76,3.167 6.188,3.406 0.427,0.24 6.281,4.74 6.708,4.979 0.427,0.24 5.292,4.75 5.719,4.99 0.427,0.24 3.792,4.656 4.219,4.896 0.427,0.24 1.833,4.656 2.26,4.896 0.427,0.24 0.625,4.646 1.052,4.885 0.427,0.24 1.604,6.25 2.031,6.49 0.427,0.24 4.719,6.25 5.146,6.49 0.427,0.24 3.302,7.844 3.729,8.083 0.427,0.24 0.948,1.188 0.708,0.74 0.708,0.74 0.594,0.74 true 1.604,1.094 1.938,0.802 1.938,0.802 2.104,0.802 true 1.625,1.417 1.958,1.125 1.958,1.125 2.125,1.125 true 1.625,1.896 1.958,1.604 1.958,1.604 2.125,1.604 true 1.615,0.646 1.615,0.229 1.615,0.229 1.76,0.229 true 0.156,0.146 0.531,0.385 0.375,0.24 12 false *A 1.844,0.156 2.156,0.354 0.313,0.198 10 false *1 2.198,0.708 2.771,0.969 0.573,0.26 10 false G217 0.083,0.688 0.563,0.896 0.479,0.208 10 false 2Q (*B) 0.094,0.906 0.635,1.125 0.542,0.219 10 false 2P (*C) 0.854,1.833 1.125,2.063 0.271,0.229 10 false 2M 0.896,2.229 1.167,2.458 0.271,0.229 10 false 2K 0.927,2.438 1.198,2.667 0.271,0.229 10 false 2L 2.208,1.052 2.802,1.302 0.594,0.25 10 false G218 2.219,1.521 2.656,1.719 0.438,0.198 10 false G216 3.76,0.99 3.969,1.208 0.208,0.219 10 false A 5.854,1.104 6.135,1.313 0.281,0.208 10 false 2N 5.844,1.75 6.125,1.958 0.281,0.208 10 false 2O 5.802,3.219 6.24,3.438 0.438,0.219 10 false G217 3.594,3.208 4.031,3.427 0.438,0.219 10 false G218 1.292,3.208 1.729,3.427 0.438,0.219 10 false G216 3.906,4.688 4.24,4.917 0.333,0.229 10 false 2M 0.75,4.677 1.021,4.906 0.271,0.229 10 false 2Q 1.125,4.677 1.396,4.906 0.271,0.229 10 false *B 2.344,4.677 2.615,4.906 0.271,0.229 10 false *C 1.99,4.688 2.323,4.917 0.333,0.229 10 false 2P 5.448,4.792 5.781,5.021 0.333,0.229 10 false 2L 6.417,4.771 6.75,5 0.333,0.229 10 false 2K 4.844,6.281 5.177,6.51 0.333,0.229 10 false 2O 1.74,6.281 2.073,6.51 0.333,0.229 10 false 2N 3.469,7.885 3.802,8.115 0.333,0.229 10 false A
*A Main Body ECU (Multiplex Network Body ECU) with 3 connectors *B for LHD
*C for RHD - -
*1 Main Body ECU (Multiplex Network Body ECU) - -


E373865C05
4.635,3.208 5.052,3.427 0.417,0.219 2.177,3.198 2.594,3.417 0.417,0.219 0.823,4.698 1.24,4.917 0.417,0.219 1.833,4.688 2.25,4.906 0.417,0.219 3.792,4.688 4.208,4.906 0.417,0.219 6.281,4.771 6.698,4.99 0.417,0.219 5.292,4.781 5.708,5 0.417,0.219 4.75,6.271 5.167,6.49 0.417,0.219 1.583,6.281 2,6.5 0.417,0.219 3.375,7.865 3.792,8.083 0.417,0.219 1.635,0.656 1.635,0.198 1.635,0.198 1.802,0.198 true 0.948,1.115 0.719,0.677 0.719,0.677 0.594,0.677 true 1.625,1.479 1.896,1.115 1.896,1.115 2.042,1.115 true 1.635,1.854 1.906,1.49 1.906,1.49 2.052,1.49 true 0.177,0.125 0.552,0.365 0.375,0.24 12 false *A 0.104,0.865 0.625,1.042 0.521,0.177 10 false 2P (*C) 0.104,0.625 0.635,0.792 0.531,0.167 10 false 2Q (*B) 1.896,0.125 2.198,0.323 0.302,0.198 10 false *1 2.125,1.042 2.594,1.24 0.469,0.198 10 false G218 2.125,1.417 2.635,1.635 0.51,0.219 10 false G216 3.781,0.969 4.083,1.167 0.302,0.198 10 false A 5.844,1.115 6.146,1.313 0.302,0.198 10 false 2N 5.854,1.771 6.156,1.969 0.302,0.198 10 false 2O 0.865,1.854 1.167,2.052 0.302,0.198 10 false 2M 0.896,2.229 1.198,2.427 0.302,0.198 10 false 2K 0.927,2.448 1.229,2.646 0.302,0.198 10 false 2L 2.219,3.229 2.688,3.438 0.469,0.208 10 false G216 4.667,3.25 5.135,3.458 0.469,0.208 10 false G218 6.406,4.802 6.698,5 0.292,0.198 10 false 2K 5.438,4.813 5.729,5.01 0.292,0.198 10 false 2L 3.896,4.729 4.188,4.927 0.292,0.198 10 false 2M 1.979,4.719 2.271,4.917 0.292,0.198 10 false 2P 0.948,4.719 1.24,4.917 0.292,0.198 10 false 2Q 1.302,4.708 1.594,4.906 0.292,0.198 10 false *B 2.333,4.708 2.625,4.906 0.292,0.198 10 false *C 1.698,6.313 1.99,6.51 0.292,0.198 10 false 2N 4.875,6.302 5.167,6.5 0.292,0.198 10 false 2O 3.552,7.906 3.844,8.104 0.292,0.198 10 false A
*A Main Body ECU (Multiplex Network Body ECU) with 2 connectors *B for LHD
*C for RHD - -
*1 Main Body ECU (Multiplex Network Body ECU) - -


a.

Remove the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A-31 (BECU) - Body ground - Battery power supply Always 11 to 14 V
A-32 (IG) - Body ground - Ignition switch power supply Ignition switch ON 11 to 14 V
A-32 (IG) - Body ground - Ignition switch power supply Ignition switch off Below 1 V
A-30 (ACC) - Body ground - ACC power supply Ignition switch ACC 11 to 14 V
A-30 (ACC) - Body ground - ACC power supply Ignition switch off Below 1 V
A-11 (GND1) - Body ground - Ground Always Below 1 Ω


c.

Install the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G218-6 (FLCY) - Body ground R - Body ground Front door LH courtesy switch input Front door LH open Below 1 V
G218-6 (FLCY) - Body ground R - Body ground Front door LH courtesy switch input Front door LH closed Pulse generation
G218-27 (FRCY) - Body ground B - Body ground Front door RH courtesy switch input Front door RH open Below 1 V
G218-27 (FRCY) - Body ground B - Body ground Front door RH courtesy switch input Front door RH closed Pulse generation