Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM › 2017.08–2021.06
RM27T0E _58 Vehicle Interior _053730 DOOR LOCK _0261036 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  Power Source Circuit  


DESCRIPTION

The main power source for the main body ECU (multiplex network body ECU) is supplied via the door control battery.

WIRING DIAGRAM

B489415E01
1.781,6.021 4.083,6.229 2.302,0.208 10 false Driver Side Junction Block Assembly 4.885,6.313 6.531,6.677 1.646,0.365 10 false Main Body ECU (Multiplex Network Body ECU) 4.458,5.552 4.802,5.833 0.344,0.281 10 false A 1.177,5.552 1.521,5.833 0.344,0.281 10 false 2M 1.208,5.375 1.552,5.656 0.344,0.281 10 false 22 2.823,2.865 3.365,3.177 0.542,0.313 10 false EDOR 2.646,2.854 3.188,3.167 0.542,0.313 10 false 3 4.708,5.448 5.25,5.76 0.542,0.313 10 false BECU 4.427,5.385 4.969,5.698 0.542,0.313 10 false 31 6.26,5.552 6.823,5.896 0.563,0.344 10 false IC 2.823,2.333 3.365,2.646 0.542,0.313 10 false BECU 0.656,2.375 1.542,2.677 0.885,0.302 10 false from Battery 0.656,0.594 1.542,0.896 0.885,0.302 10 false from Battery 2.823,0.552 3.365,0.865 0.542,0.313 10 false BATB 2.656,2.323 3.198,2.635 0.542,0.313 10 false 4 2.667,0.552 3.208,0.865 0.542,0.313 10 false 5 1.927,0.792 2.771,1.094 0.844,0.302 10 false D/L NO.1 5.938,2.875 6.479,3.188 0.542,0.313 10 false GND1 6.427,2.875 6.969,3.188 0.542,0.313 10 false 2 3.896,3.75 5.542,4.115 1.646,0.365 10 false Door Control Battery 3.729,3.552 5.375,3.917 1.646,0.365 10 false A104 2.01,2.573 2.854,2.875 0.844,0.302 10 false ECU-B

CAUTION / NOTICE / HINT

NOTICE:
·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

w/ Entry and Start System

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (DOOR CONTROL BATTERY - BATTERY AND BODY GROUND)
a.
B377768C29
0.323,0.948 0.823,1.281 0.5,0.333 1.427,1.042 0.99,0.26 true 1.802,1.042 2.333,0.156 true 1.99,1.042 2.625,0.438 true 2.385,0.063 3,0.26 0.615,0.198 10 false BECU 0.438,1.042 1.052,1.24 0.615,0.198 10 false A104 2.708,0.354 3.323,0.552 0.615,0.198 10 false BATB 0.573,0.177 1.188,0.375 0.615,0.198 10 false GND1 0.042,0.063 0.656,0.26 0.615,0.198 10 false *a
*a Front view of wire harness connector
(to Door Control Battery)


Disconnect the door control battery connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A104-4 (BECU) - Body ground Always 11 to 14 V
A104-5 (BATB) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A104-2 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL BATTERY - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL BATTERY - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the A104 door control battery connector.


b.

Disconnect the 2M driver side junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A104-3 (EDOR) - 2M-22 Always Below 1 Ω
A104-3 (EDOR) or 2M-22 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY
a.

Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

B489417E01
1.813,0.635 2.375,0.865 0.563,0.229 5.302,0.229 5.865,0.458 0.563,0.229 2.083,0.667 2.24,0.865 0.156,0.198 10 false A 5.49,0.271 5.781,0.51 0.292,0.24 10 false 2M

Standard Resistance:
Tester Connection Condition Specified Condition
A-31 (BECU) - 2M-22 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK DOOR CONTROL BATTERY (POWER OUTPUT)

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

4.CHECK DOOR CONTROL BATTERY (POWER OUTPUT)
a.

Turn the ignition switch off.


b.

Remove the ECU-B fuse from the engine room relay block.


c.
E317654C04
1.531,0.177 1.948,0.427 0.417,0.25 1.375,1.76 1.771,1.031 true 1.573,0.219 1.979,0.438 0.406,0.219 10 false A104 1.188,1.781 1.646,1.979 0.458,0.198 10 false EDOR 0.125,0.052 0.531,0.271 0.406,0.219 10 false *a
*a Component with harness connected
(Door Control Battery)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A104-3 (EDOR) - Body ground Approximately 90 seconds or more elapsed after ignition switch turned to ON (door control battery fully charged) → Approximately 30 minutes or more elapsed after ignition switch turned off (door control battery fully discharged) 11 to 14 V → Below 2 V


HINT:

Charge and discharge times differ depending on the charging amount of the door control battery.



Result:
Proceed to
OK
NG



OK

5.CHECK DOOR CONTROL BATTERY (POWER OUTPUT)

NG

5.CHECK DOOR CONTROL BATTERY (POWER OUTPUT)
a.

Turn the ignition switch off.


b.

Leave the vehicle as is for 30 minutes (wait until the door control battery is discharged).

HINT:

Discharge time is reduced when the door control battery is not fully charged.



c.
E317654C04
1.531,0.177 1.948,0.427 0.417,0.25 1.375,1.76 1.771,1.031 true 1.573,0.219 1.979,0.438 0.406,0.219 10 false A104 1.188,1.781 1.646,1.979 0.458,0.198 10 false EDOR 0.125,0.052 0.531,0.271 0.406,0.219 10 false *a
*a Component with harness connected
(Door Control Battery)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A104-3 (EDOR) - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG