When the brake pedal is depressed, the stop light switch assembly sends a signal to the ECM. When the ECM receives this signal, it cancels control of vehicle speed by the cruise control system. The fail-safe function operates to enable normal driving even if there is a malfunction in the stop light switch assembly signal circuit. The cancellation condition occurs when voltage is applied to terminal STP. When the brake pedal is depressed, voltage is applied to terminal STP of the ECM through the STOP fuse and the stop light switch assembly, and the ECM cancels control of vehicle speed by the cruise control system.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| P0571 | Brake Switch "A" Circuit | When the ignition switch ON and the cruise control system is operating, the voltage of the STP and ST1- terminals of the ECM are less than 1 V for 0.5 seconds or more. | ·
Stop light switch assembly ·
Harness or connector ·
ECM |
Inspect the fuses for circuits related to this system before performing the following procedure.
Before replacing the ECM, refer to Service Bulletin.
After performing repairs on the vehicle, clear the DTCs and perform the following procedure to check that DTCs are not output.
Turn the ignition switch ON.
Turn the cruise control system on using the cruise control main switch (ON-OFF button).
Depress the brake pedal for 0.5 seconds or more.
| *a | Front view of wire harness connector
(to Stop Light Switch Assembly) |
Disconnect the A99 stop light switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A99-2 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A99-7 (B) - Body ground | Always | 11 to 14 V |
| A99-6 (B) - Body ground | Ignition switch ON | 11 to 14 V |
| A99-6 (B) - Body ground | Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the stop light switch assembly.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 1GR-FE, Automatic Transmission
Disconnect the A99 switch connector.
Disconnect the F56 ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F56-34 (ST1-) - A99-5 (L) | Always | Below 1 Ω |
| F56-35 (STP) - A99-3 (L) | Always | Below 1 Ω |
| F56-34 (ST1-) or A99-5 (L) - Body ground | Always | 10 kΩ or higher |
| F56-35 (STP) or A99-3 (L) - Body ground | Always | 10 kΩ or higher |
for 1GR-FE, Manual Transmission
Disconnect the A99 switch connector.
Disconnect the G55 and G56 ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G55-8 (ST1-) - A99-5 (L) | Always | Below 1 Ω |
| G56-18 (STP) - A99-3 (L) | Always | Below 1 Ω |
| G55-8 (ST1-) or A99-5 (L) - Body ground | Always | 10 kΩ or higher |
| G56-18 (STP) or A99-3 (L) - Body ground | Always | 10 kΩ or higher |
for 2TR-FE
Disconnect the A99 switch connector.
Disconnect the G180 ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G180-11 (ST1-) - A99-5 (L) | Always | Below 1 Ω |
| G180-10 (STP) - A99-3 (L) | Always | Below 1 Ω |
| G180-11 (ST1-) or A99-5 (L) - Body ground | Always | 10 kΩ or higher |
| G180-10 (STP) or A99-3 (L) - Body ground | Always | 10 kΩ or higher |
for 1KD-FTV
Disconnect the A99 switch connector.
Disconnect the G57 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G57-9 (ST1-) - A99-5 (L) | Always | Below 1 Ω |
| G57-8 (STP) - A99-3 (L) | Always | Below 1 Ω |
| G57-9 (ST1-) or A99-5 (L) - Body ground | Always | 10 kΩ or higher |
| G57-8 (STP) or A99-3 (L) - Body ground | Always | 10 kΩ or higher |
for 1GD-FTV
Disconnect the A99 switch connector.
Disconnect the G185 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G185-12 (ST1-) - A99-5 (L) | Always | Below 1 Ω |
| G185-13 (STP) - A99-3 (L) | Always | Below 1 Ω |
| G185-12 (ST1-) or A99-5 (L) - Body ground | Always | 10 kΩ or higher |
| G185-13 (STP) or A99-3 (L) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for 1GR-FE: Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>ECM>REMOVAL
for 1KD-FTV: Click hereEngine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECM>REMOVAL
for 1GD-FTV: Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
for 2TR-FE: Click hereEngine / Hybrid System>2TR-FE (ENGINE CONTROL)>ECM>REMOVAL
NG