Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053696 CRUISE CONTROL _0260747 CRUISE CONTROL SYSTEM J

CRUISE CONTROL  CRUISE CONTROL SYSTEM  Cruise Control Switch Circuit  


DESCRIPTION

The cruise control main switch (ON-OFF button) is used to turn the cruise control system on and off, as well as operate 7 functions: SET, - (COAST), TAP-DOWN, RES (RESUME), + (ACCEL), TAP-UP and CANCEL. The SET, TAP-DOWN and - (COAST) functions, and the RES (RESUME), TAP-UP and + (ACCEL) functions are operated with the same switch. The cruise control main switch contains momentary type contacts for each function. The contacts close only while the cruise control main switch is being operated in the direction of the relative function arrow, and open when the cruise control main switch is released. The voltage at the terminal of the ECM changes as each of the different contacts open or close. The ECM reads this voltage and controls the SET, - (COAST), RES (RESUME), + (ACCEL), and CANCEL functions accordingly.

WIRING DIAGRAM

C382181E01
0.5,2.01 1.417,2.208 0.917,0.198 10 false CANCEL 1.302,2.021 1.917,2.219 0.615,0.198 10 false -SET 2.083,2.031 2.698,2.229 0.615,0.198 10 false +RES 2.844,2.031 3.76,2.229 0.917,0.198 10 false ON-OFF 3.094,1.583 3.552,1.781 0.458,0.198 10 false CCS 4.604,1.583 5.063,1.781 0.458,0.198 10 false CCS 6.323,0.521 6.781,0.719 0.458,0.198 10 false CCS 3.094,2.479 3.552,2.677 0.458,0.198 10 false ECC 4.594,2.479 5.052,2.677 0.458,0.198 10 false ECC 0.958,3.104 2.813,3.365 1.854,0.26 10 false Cruise Control Main Switch 4.323,3.094 5.438,3.5 1.115,0.406 10 false Spiral Cable Sub-assembly 0.198,3.698 2.979,3.979 2.781,0.281 10 false *1: for 1GR-FE, Automatic Transmission 0.198,4.031 2.979,4.313 2.781,0.281 10 false *2: for 1GR-FE, Manual Transmission 0.208,4.365 2.354,4.563 2.146,0.198 10 false *3: for 2TR-FE 0.219,4.688 2.51,4.885 2.292,0.198 10 false *4: for 1KD-FTV 0.219,5.01 2.51,5.208 2.292,0.198 10 false *5: for 1GD-FTV 2.115,4.667 4.292,4.938 2.177,0.271 10 false *6: Cruise Control Switch Wire 4.125,0.521 4.583,0.719 0.458,0.198 10 false G56 4.573,0.521 5.031,0.719 0.458,0.198 10 false G56 5,0.51 5.458,0.708 0.458,0.198 10 false G181 5.479,0.521 5.938,0.719 0.458,0.198 10 false G57 5.885,0.521 6.344,0.719 0.458,0.198 10 false G185 5.021,1.688 5.635,1.885 0.615,0.198 10 false G208 5.021,2.594 5.635,2.792 0.615,0.198 10 false G208 4.073,1.688 4.531,1.885 0.458,0.198 10 false z7 4.063,2.583 4.521,2.781 0.458,0.198 10 false z7 4.198,0.281 4.51,0.479 0.313,0.198 10 false 1 4.615,0.292 4.927,0.49 0.313,0.198 10 false 11 5.083,0.292 5.396,0.49 0.313,0.198 10 false 22 5.51,0.292 5.823,0.49 0.313,0.198 10 false 14 5.969,0.302 6.281,0.5 0.313,0.198 10 false 26 3.51,1.594 3.823,1.792 0.313,0.198 10 false 3 3.521,2.479 3.833,2.677 0.313,0.198 10 false 1 4.094,1.458 4.406,1.656 0.313,0.198 10 false 3 4.104,2.375 4.417,2.573 0.313,0.198 10 false 4 5.135,1.469 5.448,1.667 0.313,0.198 10 false 1 5.156,2.365 5.469,2.563 0.313,0.198 10 false 2 3.677,2.708 3.99,2.906 0.313,0.198 10 false *6 6,0.74 6.313,0.938 0.313,0.198 10 false *5 4.646,0.74 4.958,0.938 0.313,0.198 10 false *2 4.167,0.74 4.479,0.938 0.313,0.198 10 false *1 5.104,0.74 5.417,0.938 0.313,0.198 10 false *3 5.563,0.74 5.875,0.938 0.313,0.198 10 false *4 6.448,3.865 6.906,4.063 0.458,0.198 10 false ECM 3.667,1.813 3.979,2.01 0.313,0.198 10 false *6 5.979,2.365 6.292,2.563 0.313,0.198 10 false 21 5.885,2.583 6.344,2.781 0.458,0.198 10 false G181 6.344,2.604 6.979,2.854 0.635,0.25 10 false ECCS 5.604,3.135 5.917,3.333 0.313,0.198 10 false *7 5.625,2.479 5.938,2.677 0.313,0.198 10 false *3 2.135,5 4.281,5.198 2.146,0.198 10 false *7: except 2TR-FE

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

Before replacing the ECM refer to Service Bulletin.



PROCEDURE

1.READ VALUE ON GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Cruise Control / Data List.


e.

for 1GR-FE (for Manual Transmission):

Read the Data List according to the display on the GTS.

Powertrain > Cruise Control > Data List

Tester Display Measurement Item Range Normal Condition Diagnostic Note
Main SW M-CPU Cruise control main switch signal (Main CPU) ON or OFF ON: Cruise control main switch on
OFF: Cruise control main switch off
-
Cancel Switch CANCEL switch signal ON or OFF ON: CANCEL switch on
OFF: CANCEL switch off
-
SET/COAST Switch -SET switch signal ON or OFF ON: -SET switch on
OFF: -SET switch off
-
RES/ACC Switch +RES switch signal ON or OFF ON: +RES switch on
OFF: +RES switch off
-


f.

except 1GR-FE (for Manual Transmission):

Read the Data List according to the display on the GTS.

Powertrain > Cruise Control > Data List

Tester Display Measurement Item Range Normal Condition Diagnostic Note
Cancel Switch CANCEL switch status ON or OFF ON: CANCEL switch on
OFF: CANCEL switch off
-
-SET Switch -SET switch status ON or OFF ON: CANCEL switch on
OFF: CANCEL switch off
-
+RES Switch +RES switch status ON or OFF ON: -SET switch on
OFF: -SET switch off
-
Cruise Ready Main-CPU Cruise control system standby condition ON or OFF Each time cruise control main switch is pushed, ON or OFF changes -


OK:

When the cruise control main switch is operated, the display changes as shown above.


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT CRUISE CONTROL MAIN SWITCH
2.INSPECT CRUISE CONTROL MAIN SWITCH
a.

Remove the cruise control main switch.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL MAIN SWITCH>REMOVAL


b.

Inspect the cruise control main switch.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL MAIN SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK CRUISE CONTROL SWITCH WIRE

NG

3.CHECK CRUISE CONTROL SWITCH WIRE
a.
A306566C86
0.333,1.167 0.833,1.417 0.5,0.25 0.354,0.76 0.667,0.917 0.313,0.156 10 false *a 0.5,3.094 0.813,3.25 0.313,0.156 10 false *b 0.51,1.208 0.823,1.406 0.313,0.198 10 false z7
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)
*b Front view of wire harness connector
(to Cruise Control Switch)


Remove the cruise control switch wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Specified Condition
Cruise control switch side connector terminal 3 - z7-3 Below 1 Ω
Cruise control switch side connector terminal 1 - z7-4 Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM AND BODY GROUND)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM AND BODY GROUND)
a.

Disconnect the G208 spiral cable sub-assembly connector.


b.

Disconnect the G56*1, G57*2, G181*3 or G185*4 ECM connector.

·

*1: for 1GR-FE

·

*2: for 1KD-FTV

·

*3: for 2TR-FE

·

*4: for 1GD-FTV



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for 1GR-FE, Automatic Transmission):
Tester Connection Condition Specified Condition
G208-1 (CCS) - G56-1 (CCS) Always Below 1 Ω
G208-2 (ECC) - Body ground Always Below 1 Ω
G208-1 (CCS) or G56-1 (CCS) - Body ground Always 10 kΩ or higher


Standard Resistance (for 1GR-FE, Manual Transmission):
Tester Connection Condition Specified Condition
G208-1 (CCS) - G56-11 (CCS) Always Below 1 Ω
G208-2 (ECC) - Body ground Always Below 1 Ω
G208-1 (CCS) or G56-11 (CCS) - Body ground Always 10 kΩ or higher


Standard Resistance (for 1KD-FTV):
Tester Connection Condition Specified Condition
G208-1 (CCS) - G57-14 (CCS) Always Below 1 Ω
G208-2 (ECC) - Body ground Always Below 1 Ω
G208-1 (CCS) or G57-14 (CCS) - Body ground Always 10 kΩ or higher


Standard Resistance (for 2TR-FE):
Tester Connection Condition Specified Condition
G208-1 (CCS) - G181-22 (CCS) Always Below 1 Ω
G208-2 (ECC) - G181-21 (ECCS) Always Below 1 Ω
G208-1 (CCS) or G181-22 (CCS) - Body ground Always 10 kΩ or higher


Standard Resistance (for 1GD-FTV):
Tester Connection Condition Specified Condition
G208-1 (CCS) - G185-26 (CCS) Always Below 1 Ω
G208-2 (ECC) - Body ground Always Below 1 Ω
G208-1 (CCS) or G185-26 (CCS) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (except 2TR-FE) A
OK (for 2TR-FE) B
NG C



A

B

6.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C153-3 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR