DTC C1681 is stored if the parking assist ECU judges as a result of ifs self check that a synchronization problem is occurring in the image signal sent from the front television camera assembly to the parking assist ECU.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1681 | Front television camera power supply failure | ·
Harness or connector ·
Front television camera assembly ·
Parking assist ECU |
When "!" mark is displayed on the navigation receiver assembly*1 or radio and display receiver assembly*2 after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.
(See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>INITIALIZATION)
*1: for Navigation Receiver Type
*2: for Radio and Display Type
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as multi-terrain monitor system may be needed (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Disconnect the I7 parking assist ECU connector.
Disconnect the g1 front television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I7-36 (BCV-) - g1-2 (BCV-) | Always | Below 1 Ω |
| I7-12 (BCV+) - g1-3 (BCV+) | Always | Below 1 Ω |
| I7-35 (BGND) - g1-5 (BGND) | Always | Below 1 Ω |
| I7-11 (BCB+) - g1-6 (BCB+) | Always | Below 1 Ω |
| I7-36 (BCV-) - Body ground | Always | 10 kΩ or higher |
| I7-12 (BCV+) - Body ground | Always | 10 kΩ or higher |
| I7-35 (BGND) - Body ground | Always | 10 kΩ or higher |
| I7-11 (BCB+) - Body ground | Always | 10 kΩ or higher |
OK
NG
| *a | Component without harness connected
(Parking Assist ECU) |
Disconnect the parking assist ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 35 (BGND) - Body ground | Always | Below 1 Ω |
| 36 (BCV-) - Body ground | Always | Below 1 Ω |
OK
NG
for LHD:
(See pageAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST ECU (for LHD)>REMOVAL)
for RHD:
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST ECU (for RHD)>REMOVAL
| *a | Component with harness connected
(Parking Assist ECU) |
Disconnect the front television camera assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I7-11 (BCB+) - I7-35 (BGND) | Engine switch on (IG) | 5.5 to 7.05 V |
| I7-11 (BCB+) - I7-35 (BGND) | Engine switch off | Below 1 V |
OK
NG
for LHD:
(See pageAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST ECU (for LHD)>REMOVAL)
for RHD:
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST ECU (for RHD)>REMOVAL
Check the wave form of the front television camera assembly using an oscilloscope.
| *a | Component with harness connected
(Parking Assist ECU) |
*b | Waveform A |
| *c | Waveform B | *d | Synchronization Signal |
| *e | Video Waveform | - | - |
The video waveform changes according to the image sent by the front television camera assembly.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | I7-12 (BCV+) - I7-35 (BGND) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | ·
Waveform A: Engine switch on (IG), panoramic view monitor switch (multi-terrain monitor switch) on and camera lens is not covered, displaying an image ·
Waveform B: Engine switch on (IG), panoramic view monitor switch (multi-terrain monitor switch) on and camera lens is covered, blacking out the screen |
Waveform is as shown in the illustration.
OK
for LHD:
(See pageAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST ECU (for LHD)>REMOVAL)
for RHD:
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST ECU (for RHD)>REMOVAL
NG
(See pageAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Front)>REMOVAL)