Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › MULTI-TERRAIN MONITOR SYSTEM › 2017.08–2020.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0328431 MULTI-TERRAIN MONITOR SYSTEM C

PARK ASSIST / MONITORING  MULTI-TERRAIN MONITOR SYSTEM  C1682  Front Camera Current Malfunction  


DESCRIPTION

DTC C1682 is stored if the parking assist ECU judges as a result of its self check that there is a problem with the current supplied from the front television camera assembly connected to the parking assist ECU.

DTC Code DTC Detection Condition Trouble Area
C1682 An open or short in the front television camera signal circuit
·

Harness or connector

·

Front television camera assembly

·

Parking assist ECU



WIRING DIAGRAM

E240924E37
5.573,0.469 6.208,0.75 0.635,0.281 10 false BCB+ 5.271,0.385 5.469,0.615 0.198,0.229 10 false 11 5.573,1.271 6.104,1.521 0.531,0.25 10 false BGND 5.531,1.792 5.885,2.021 0.354,0.229 10 false I7 0.802,1.604 1.167,1.823 0.365,0.219 10 false g1 0.74,1.833 3.156,2.198 2.417,0.365 10 false Front Television Camera Assembly 5.531,1.958 6.865,2.208 1.333,0.25 10 false Parking Assist ECU 5.292,1.177 5.552,1.406 0.26,0.229 10 false 35 2.052,0.385 2.24,0.604 0.188,0.219 10 false 6 2.063,1.188 2.26,1.365 0.198,0.177 10 false 5 1.531,0.469 2,0.698 0.469,0.229 10 false BCB+ 1.49,1.281 1.958,1.51 0.469,0.229 10 false BGND

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" mark is displayed on the navigation receiver assembly*1 or radio and display receiver assembly*2 after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

(See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>INITIALIZATION)

*1: for Navigation Receiver Type

*2: for Radio and Display Type


·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as multi-terrain monitor system may be needed (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - FRONT TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the I7 parking assist ECU connector.


b.

Disconnect the g1 front television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I7-11 (BCB+) - g1-6 (BCB+) Always Below 1 Ω
I7-35 (BGND) - g1-5 (BGND) Always Below 1 Ω
I7-11 (BCB+) or g1-6 (BCB+) - Body ground Always 10 kΩ or higher
I7-35 (BGND) or g1-5 (BGND) - Body ground Always 10 kΩ or higher




OK

2.CHECK PARKING ASSIST ECU (BCB+, BGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK PARKING ASSIST ECU (BCB+, BGND)
a.
U166331C01
1.302,1.156 1.385,1.438 1.385,1.438 1.563,1.438 true 1.333,0.979 1.219,0.677 1.219,0.677 1.052,0.677 true 0.104,0.094 0.333,0.354 0.229,0.26 10 false *a 0.625,0.594 1.094,0.833 0.469,0.24 10 false BCB+ 1.583,0.542 2.073,0.771 0.49,0.229 10 false I7 1.615,1.354 2.094,1.573 0.479,0.219 10 false BGND
*a Component with harness connected
(Parking Assist ECU)


Disconnect the front television camera assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I7-35 (BGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I7-11 (BCB+) - I7-35 (BGND) Engine switch on (IG) 5.5 to 7.05 V
I7-11 (BCB+) - I7-35 (BGND) Engine switch off Below 1 V



Text in Illustration
*a Component with harness connected
(Parking Assist ECU)


OK

NG