Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › from 2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261053 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  Front Passenger Side Door Entry Unlock Function does not Operate  


DESCRIPTION

If the entry unlock function does not operate for the front passenger door only, but the entry lock function operates, the request code is being transmitted properly from the front passenger door. In this case, there may be a problem related to the unlock sensor (connection between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for front passenger door)).

WIRING DIAGRAM

B388637E89
1.302,0.76 1.917,0.958 0.615,0.198 10 false ANT1 1.313,1.906 1.927,2.104 0.615,0.198 10 false ANT2 5.302,0.76 5.917,0.958 0.615,0.198 10 false CLG2 5.302,1.906 5.917,2.104 0.615,0.198 10 false CG2B 5.854,1.177 6.469,1.375 0.615,0.198 10 false IC 6.271,2.031 6.583,2.354 0.313,0.323 10 false E 6.469,1.906 6.781,2.229 0.313,0.323 10 false 11 5.125,2.583 5.74,2.781 0.615,0.198 10 false G215 5.125,2.75 6.688,3.271 1.563,0.521 10 false Certification ECU (Smart Key ECU Assembly) 5.125,1.906 5.438,2.229 0.313,0.323 10 false 1 5.125,0.76 5.438,1.083 0.313,0.323 10 false 2 1.76,0.76 2.073,1.083 0.313,0.323 10 false 6 1.781,1.906 2.094,2.229 0.313,0.323 10 false 4 0.448,2.563 1.344,2.76 0.896,0.198 10 false N2*1, O2*2 0.427,2.74 2.76,3.302 2.333,0.563 10 false Front Door Outside Handle Assembly (for Front Passenger Door) 3.375,3 4.083,3.208 0.708,0.208 10 false *1: for LHD 3.375,3.313 4.083,3.521 0.708,0.208 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to entry and start system (for Entry Function) Precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Door locks operate normally.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (FR DOOR LOCK POS, FL DOOR LOCK POS)

NG

2.READ VALUE USING GTS (FR DOOR LOCK POS, FL DOOR LOCK POS)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Main Body
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Lock Pos Front door RH unlock detection switch signal*1 UNLOCK or LOCK UNLOCK: Front door RH unlocked
LOCK: Front door RH locked
-
FL Door Lock Pos Front door LH unlock detection switch signal*2 UNLOCK or LOCK UNLOCK: Front door LH unlocked
LOCK: Front door LH locked
-

*1: for LHD

*2: for RHD


OK:

The GTS display changes correctly in response to the lock/unlock operation of the front passenger door.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (P-DOOR TOUCH SENSOR)

NG

GO TO LIGHTING SYSTEM (Proceed to Door Unlock Detection Switch Circuit)

3.READ VALUE USING GTS (P-DOOR TOUCH SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Data List.


e.

Read the Data List according to the display on the GTS.


f.

Open and close the front passenger door.


g.

With the electrical key transmitter sub-assembly outside of the vehicle, press the lock switch of the electrical key transmitter sub-assembly to lock all of the doors.


h.

Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the front passenger door.


i.

Check that the LED of the electrical key transmitter sub-assembly blinks.


j.

Read the Data List according to the display on the GTS.


k.
B433958C01
0.106,0.16 0.693,0.303 0.587,0.144 10 *A 2.598,2.05 3.185,2.194 0.587,0.144 10 *a 0.518,4.181 1.105,4.325 0.587,0.144 10 *a 0.106,2.145 0.693,2.288 0.587,0.144 10 *B 2.173,1.461 2.414,2.132 2.414,2.132 2.551,2.132 false 1.237,3.833 0.927,4.263 0.927,4.263 0.773,4.263 false
*A for RHD
*B for LHD
*a Unlock Sensor (Backside)


Touch the unlock sensor on the backside of the front door outside handle assembly (for front passenger door).

HINT:

When checking the operation of the unlock sensor again, make sure to perform the procedure from step (f).


Entry&Start
Tester Display Measurement Item Range Normal Condition Diagnostic Note
P-Door Touch Sensor Front passenger door touch sensor (unlock sensor) ON or OFF ON: Front passenger door touch sensor (unlock sensor) touched
OFF: Front passenger door touch sensor (unlock sensor) not touched
·

Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate.



OK:

The GTS display changes correctly in response to the operation of the front door outside handle assembly (for front passenger door).



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR))
4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR))

*1: for LHD

*2: for RHD


a.

Disconnect the G215 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the N2*1 or O2*2 front door outside handle assembly (for front passenger door) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
G215-2 (CLG2) - N2-6 (ANT1) Always Below 1 Ω
G215-1 (CG2B) - N2-4 (ANT2) Always Below 1 Ω
G215-2 (CLG2) or N2-6 (ANT1) - Body ground Always 10 kΩ or higher
G215-1 (CG2B) or N2-4 (ANT2) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
G215-2 (CLG2) - O2-6 (ANT1) Always Below 1 Ω
G215-1 (CG2B) - O2-4 (ANT2) Always Below 1 Ω
G215-2 (CLG2) or O2-6 (ANT1) - Body ground Always 10 kΩ or higher
G215-1 (CG2B) or O2-4(ANT2) - Body ground Always 10 kΩ or higher



d.

Reconnect the N2*1 or O2*2 front door outside handle assembly (for front passenger door) connector.


e.

Reconnect the G215 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

5.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR) (INPUT TO FRONT PASSENGER DOOR UNLOCK SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR) (INPUT TO FRONT PASSENGER DOOR UNLOCK SENSOR)
B343198C86
5.073,0.333 5.469,0.542 0.396,0.208 3.313,0.333 3.708,0.542 0.396,0.208 1.667,0.333 2.063,0.542 0.396,0.208 5.667,2.063 5.917,1.25 true 6.188,2.073 6.031,1.396 true 6.25,2.125 6.406,2.323 0.156,0.198 10 false E 5.521,2.125 5.958,2.344 0.438,0.219 10 false CLG2 5.115,0.375 5.552,0.594 0.438,0.219 10 false G215 0.594,0.094 1.115,0.292 0.521,0.198 10 false *a 1.156,2.75 1.896,3.042 0.74,0.292 10 false *b 0.771,3.708 1.281,4.031 0.51,0.323 10 false GND 0.927,4.385 1.188,4.563 0.26,0.177 10 false *c 2.365,4.396 2.625,4.573 0.26,0.177 10 false *c 1.667,4.49 1.927,4.667 0.26,0.177 10 false *d 3.365,0.375 3.823,0.573 0.458,0.198 10 false G214 1.708,0.375 2.167,0.573 0.458,0.198 10 false G213
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
*b Waveform 1
*c Unlock sensor not touched *d Unlock sensor touched


a.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition
G215-2 (CLG2) - G215-11 (E) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not near the vehicle

5.

Front passenger door unlock sensor touched


5 V/DIV., 50 ms./DIV. Pulse generation
(See waveform 1)



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR)