Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM › from 2017.08
RM27T0E _58 Vehicle Interior _053730 DOOR LOCK _0261036 POWER DOOR LOCK CONTROL SYSTEM Y

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use these procedures to troubleshoot the power door lock control system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS CHECK
2.CUSTOMER PROBLEM ANALYSIS CHECK
HINT:
·

In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.

·

Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.

·

The following 5 items are important points for problem analysis:


What Vehicle model, system name
When Date, time, occurrence frequency, whether the problem occurred recently or has been occurring for a long time
Where Whether the problem occurs at a specific location
Under what conditions? Whether the doors were locked or unlocked, whether the ignition switch was ON, whether the engine has started
How did it happen? Problem symptoms


Result:
Proceed to
NEXT



NEXT

3.READ AND SAVE OPERATION HISTORY
3.READ AND SAVE OPERATION HISTORY
NOTICE:
·

If the vehicle or vehicle controls are operated (for example, during initial inspection when the vehicle is brought in for repair) before operation history has been read out and saved, the operation history information could be lost.

·

The function "Read operation history" uses the current system time setting inside the GTS and the time counter inside the controlling ECU to calculate the timings shown in the operation history. For this reason, before reading out the operation history, first make sure that the GTS system clock is accurately set to the current time.



a.

Result:
Proceed to
NEXT



NEXT

4.INSPECT BATTERY VOLTAGE
4.INSPECT BATTERY VOLTAGE
Standard voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the battery before proceeding.

Result:
Proceed to
NEXT



NEXT

5.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
5.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
a.

Using the GTS to check if the CAN communication system is functioning normally.


Result:
Result Proceed to
CAN DTC is not output A
CAN DTC is output (w/ Central Gateway ECU) B
CAN DTC is output (w/o Central Gateway ECU) C




A

6.CHECK COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*

B

C

6.CHECK COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*
a.

Check if the LIN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

Result:
Result Proceed to
LIN DTC is not output A
LIN DTC is output B




A

7.CHECK FOR DTC*

B

7.CHECK FOR DTC*

b.

Recheck for DTCs.


Result:
Result Proceed to
DTC is not output A
DTC is output B



A

8.PROBLEM SYMPTOMS TABLE

B

GO TO DIAGNOSTIC TROUBLE CODE CHART

8.PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault is not listed in Problem Symptoms Table (Fault can be simulated) A
Fault is not listed in Problem Symptoms Table (Fault cannot be simulated) B
Fault is listed in problem symptoms table C



A

9.OVERALL ANALYSIS AND TROUBLESHOOTING

B

C

ADJUST, REPAIR OR REPLACE IN ACCORDANCE WITH PROBLEM SYMPTOMS TABLE

9.OVERALL ANALYSIS AND TROUBLESHOOTING

NEXT

10.REPAIR OR REPLACE
10.REPAIR OR REPLACE
Result:
Proceed to
NEXT



NEXT

11.CONFIRMATION TEST
11.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END