Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) › 2017.08–2020.08
RM27T0E _58 Vehicle Interior _053739 HEATING / AIR CONDITIONING _0261169 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  Air Conditioning Compressor Magnetic Clutch Circuit  


DESCRIPTION

When the air conditioning amplifier assembly is turned ON, a magnet clutch assembly ON signal is sent from the MGC terminal of the air conditioning amplifier assembly. Then, the A/C COMP relay turns on to operate the magnet clutch assembly.

WIRING DIAGRAM

E198320E25
6.01,1.604 6.604,1.896 0.594,0.292 10 false MGC 5.51,5.104 7.083,5.625 1.573,0.521 10 false Air Conditioning Amplifier Assembly 4.375,3.813 4.76,4.177 0.385,0.365 10 false 3 3.281,3.823 3.594,4.073 0.313,0.25 10 false 1 1.604,4.5 2.865,5.219 1.26,0.719 10 false Magnet Clutch Assembly 3.26,4.5 4.677,5.104 1.417,0.604 10 false Cooler Compressor Assembly 2.177,1.51 2.615,1.688 0.438,0.177 10 false 1 3.115,1.5 3.427,1.698 0.313,0.198 10 false 2 3.104,0.969 3.583,1.177 0.479,0.208 10 false 3 2.188,0.979 2.385,1.135 0.198,0.156 10 false 5 2.344,1.958 3.333,2.354 0.99,0.396 10 false A/C COMP 2.271,3.063 3.75,3.448 1.479,0.385 10 false from Battery 2.24,2.635 4.125,2.979 1.885,0.344 10 false from IG NO.1 Relay 5.688,1.5 6.052,1.698 0.365,0.198 10 false 20 5.5,4.948 5.948,5.156 0.448,0.208 10 false G25 1.615,4.333 2.031,4.552 0.417,0.219 10 false A 3.25,4.333 3.75,4.563 0.5,0.229 10 false C39 3.906,3.823 4.427,4.052 0.521,0.229 10 false MG+ 1.313,1.74 1.917,2.188 0.604,0.448 10 false IG1 1.115,1.26 1.927,1.479 0.813,0.219 10 false A/C COMP

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.INSPECT MAGNET CLUTCH RELAY (A/C COMP)
a.

Remove the A/C COMP relay from the engine room No. 1 relay block, junction block.




OK

2.INSPECT COOLER COMPRESSOR ASSEMBLY

NG

REPLACE MAGNET CLUTCH RELAY (A/C COMP)

2.INSPECT COOLER COMPRESSOR ASSEMBLY
a.
U149316E03
1.75,1.135 2.042,1.552 true 0.646,2.417 0.896,2.583 0.25,0.167 10 false A 2.094,1.51 2.469,1.677 0.375,0.167 10 false MG+

for 1GR-FE:

Remove the cooler compressor assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>COMPRESSOR (for 1GR-FE)>REMOVAL).


b.

for 1KD-FTV:

Remove the cooler compressor assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>COMPRESSOR(for 1KD-FTV)>REMOVAL).


c.

for 2TR-FE:

Remove the cooler compressor assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>COMPRESSOR (for 2TR-FE)>REMOVAL).


d.

Disconnect the A magnet clutch connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (MG+) - A-1 Always Below 1 Ω
3 (MG+) - Body ground Always 10 kΩ or higher



Result
Result Proceed to
OK A
NG (for 1GR-FE) B
NG (for 1KD-FTV) C
NG (for 2TR-FE) D


A

3.INSPECT MAGNET CLUTCH ASSEMBLY

B

C

D

3.INSPECT MAGNET CLUTCH ASSEMBLY
a.
E198322E01
1.108,1.8 1.473,1.973 0.365,0.173 10 MG+ 1.323,1.779 1.669,1.372 false

Reconnect the A magnet clutch connector.


b.

Apply battery voltage to the magnet clutch assembly and check the operation of the magnet clutch assembly.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 3 (MG+)
Battery negative (-) → Body ground
Magnet clutch assembly operating sound can be heard, and magnetic clutch hub and rotor lock.



Result
Result Proceed to
OK A
NG (for 1GR-FE) B
NG (for 1KD-FTV) C
NG (for 2TR-FE) D


A

4.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK - BATTERY)

B

C

D

4.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK - BATTERY)
a.

Remove the A/C COMP relay from the engine room No. 1 relay block, junction block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A/C COMP relay terminal 1 - Body ground Ignition switch ON 11 to 14 V
A/C COMP relay terminal 5 - Body ground Always 11 to 14 V




OK

5.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BATTERY)
a.
U170585E02
2.802,2.333 2.938,1.865 true 0.125,0.042 0.385,0.26 0.26,0.219 10 false *a 0.625,1.26 0.927,1.458 0.302,0.198 10 false G25 2.979,1.76 3.354,1.958 0.375,0.198 10 false MGC

Disconnect the G25 amplifier connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G25-20 (MGC) - Body ground Ignition switch off Below 1 V
G25-20 (MGC) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)



OK

6.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK - COOLER COMPRESSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK - COOLER COMPRESSOR)
a.

Remove the A/C COMP relay from the engine room No. 1 relay block, junction block.


b.

Disconnect the C39 compressor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A/C COMP relay terminal 3 - C39-3 (MG+) Always Below 1 Ω
C39-3 (MG+) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR