PTC heater relays are closed in accordance with signals from the air conditioning amplifier assembly and power is supplied to the quick heater assembly installed on the radiator heater unit.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Remove the PTC NO.1 or 400W INV, PTC NO.2 and PTC NO.3 relays from the engine room No. 3 relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Battery voltage is not applied to terminals 1 and 2 | 10 kΩ or higher |
| Battery voltage is applied to terminals 1 and 2 | Below 1 Ω |
OK
NG
Remove the air conditioning amplifier assembly with its connectors still connected (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G25-3 (PTC1) - Body ground | ·
Engine running (1250 rpm or more) ·
Temperature setting MAX HOT ·
Outside temperature 10°C (50°F) or less ·
Engine coolant temperature 79°C (174°F) or less ·
Headlight dimmer switch off ·
Blower switch off |
11 to 14 V |
| G25-22 (PTC2) - Body ground | ·
Engine running (1250 rpm or more) ·
Temperature setting MAX HOT ·
Outside temperature 10°C (50°F) or less ·
Engine coolant temperature 76°C (169°F) or less ·
Headlight dimmer switch off ·
Blower switch off |
|
| G25-4 (PTC3) - Body ground | ·
Engine running (1250 rpm or more) ·
Temperature setting MAX HOT ·
Outside temperature 10°C (50°F) or less ·
Engine coolant temperature 73°C (163°F) or less ·
Headlight dimmer switch off ·
Blower switch off |
|
| G25-3 (PTC1) - Body ground | ·
Engine running (1250 rpm or more) ·
Temperature setting MAX HOT ·
Outside temperature 10°C (50°F) or less ·
Engine coolant temperature 79°C (174°F) or less ·
Headlight dimmer switch off ·
Blower switch on |
Below 1 V |
| G25-22 (PTC2) - Body ground | ·
Engine running (1250 rpm or more) ·
Temperature setting MAX HOT ·
Outside temperature 10°C (50°F) or less ·
Engine coolant temperature 76°C (169°F) or less ·
Headlight dimmer switch off ·
Blower switch on |
|
| G25-4 (PTC3) - Body ground | ·
Engine running (1250 rpm or more) ·
Temperature setting MAX HOT ·
Outside temperature 10°C (50°F) or less ·
Engine coolant temperature 73°C (163°F) or less ·
Headlight dimmer switch off ·
Blower switch on |
| *a | Component with harness connected
(Air Conditioning Amplifier Assembly) |
OK
NG
Remove the PTC heater relays from the engine room No. 3 relay block.
Disconnect the G25 amplifier connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| PTC NO.1 or 400W INV relay terminal 1 - G25-3 (PTC1) | Always | Below 1 Ω |
| PTC NO.2 relay terminal 1 - G25-22 (PTC2) | ||
| PTC NO.3 relay terminal 1 - G25-4 (PTC3) | ||
| PTC NO.1 or 400W INV relay terminal 1 - Body ground | Always | 10 kΩ or higher |
| PTC NO.2 relay terminal 1 - Body ground | ||
| PTC NO.3 relay terminal 1 - Body ground |
OK
NG
Remove the PTC heater relays from the engine room No. 3 relay block.
Disconnect the G28 quick heater connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| PTC NO.1 or 400W INV relay terminal 3 - G28-2 (B) | Always | Below 1 Ω |
| PTC NO.2 relay terminal 3 - G28-3 (B) | ||
| PTC NO.3 relay terminal 3 - G28-1 (B) | ||
| PTC NO.1 or 400W INV relay terminal 3 - Body ground | Always | 10 kΩ or higher |
| PTC NO.2 relay terminal 3 - Body ground | ||
| PTC NO.3 relay terminal 3 - Body ground |
OK
NG
Remove the PTC heater relays from the engine room No. 3 relay block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| PTC NO.1 or 400W INV relay terminal 5 - Body ground | Always | 11 to 14 V |
| PTC NO.2 relay terminal 5 - Body ground | ||
| PTC NO.3 relay terminal 5 - Body ground |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| PTC NO.1 or 400W INV relay terminal 2 - Body ground | Always | Below 1 Ω |
| PTC NO.2 relay terminal 2 - Body ground | ||
| PTC NO.3 relay terminal 2 - Body ground |
| *1 | PTC NO.1 or 400W INV Relay |
| *2 | PTC NO.2 Relay |
| *3 | PTC NO.3 Relay |
| *a | Component without relay installed
(Engine Room No. 3 Relay Block) |
OK
NG
Remove the quick heater assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>PTC HEATER ASSEMBLY>REMOVAL).
Inspect the quick heater assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>PTC HEATER ASSEMBLY>INSPECTION).
OK
NG
Disconnect the G178 and G179 heater connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G178-1 (E) - Body ground | Always | Below 1 Ω |
| G179-1 (E) - Body ground |
| *a | Front view of wire harness connector
(to Quick Heater Assembly) |
OK
NG