CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
| *A | Main Body ECU (Multiplex Network Body ECU) with 3 connectors | *B | for LHD |
| *C | for RHD | - | - |
| *1 | Main Body ECU (Multiplex Network Body ECU) | - | - |
| *A | Main Body ECU (Multiplex Network Body ECU) with 2 connectors | *B | for LHD |
| *C | for RHD | - | - |
| *1 | Main Body ECU (Multiplex Network Body ECU) | - | - |
Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Connect the driver side junction block assembly connectors.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A-32 (IG) - Body ground | - | IG power supply | Engine switch on (IG) | 11 to 14 V |
| Engine switch off | Below 1 V | |||
| A-31 (BECU) - Body ground | - | Battery power supply | Always | 11 to 14 V |
| A-30 (ACC) - Body ground | - | ACC power supply | Engine switch on (ACC) | 11 to 14 V |
| Engine switch off | Below 1 V | |||
| A-11 (GND1) - Body ground | - | Ground | Always | Below 1 Ω |
Install the main body ECU (multiplex network body ECU).
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION
Measure the voltage and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
|
*1: for LHD *2: for RHD *3: w/ Glass Hatch Opener System *4: for 5 Door |
||||
| G218-6 (FLCY) - Body ground | R - Body ground | Front door courtesy light switch assembly LH signal | Front door LH open | Below 1 V |
| Front door LH closed | 11 to 14 V | |||
| G218-27 (FRCY) - Body ground | B - Body ground | Front door courtesy light switch assembly RH signal | Front door RH open | Below 1 V |
| Front door RH closed | 11 to 14 V | |||
| 2N-30 (RCTY) - Body ground*1 | R - Body ground | Rear door courtesy light switch assembly RH signal | Rear door RH open | Below 1 V |
| Rear door RH closed | 11 to 14 V | |||
| 2P-23 (RCTY) - Body ground*2 | R - Body ground | Rear door courtesy light switch assembly RH signal | Rear door RH open | Below 1 V |
| Rear door RH closed | 11 to 14 V | |||
| 2Q-33 (LCTY) - Body ground*1 | V - Body ground | Rear door courtesy light switch assembly LH signal | Rear door LH open | Below 1 V |
| Rear door LH closed | 11 to 14 V | |||
| 2O-15 (LCTY) - Body ground*2 | V - Body ground | Rear door courtesy light switch assembly LH signal | Rear door LH open | Below 1 V |
| Rear door LH closed | 11 to 14 V | |||
| 2Q-27 (BCTY) - Body ground*1 | G - Body ground | Back door courtesy light switch assembly signal | Back door open | Below 1 V |
| Back door close | 11 to 14 V | |||
| 2N-27 (BCTY) - Body ground*2 | G - Body ground | Back door courtesy light switch assembly signal | Back door open | Below 1 V |
| Back door close | 11 to 14 V | |||
| G216-27 (GCTY) - Body ground*3 | V - Body ground | Glass hatch courtesy switch input | Glass hatch open | Below 1 V |
| Engine switch off, all doors closed and glass hatch closed | 11 to 14 V | |||
| 2O-41 (LSFR) - Body ground | G - Body ground | Front door unlock detection switch RH signal | Front door RH unlocked | Below 1 V |
| Engine switch off, all doors closed and front door RH locked | 11 to 14 V | |||
| 2N-12 (LSFL) - Body ground | G - Body ground | Front door unlock detection switch LH signal | Front door LH unlocked | Below 1 V |
| Engine switch off, all doors closed and front door LH locked | 11 to 14 V | |||
| 2Q-26 (LSWL) - Body ground*1, *4 | B - Body ground | Rear door unlock detection switch LH signal | Rear door LH unlocked | Below 1 V |
| Engine switch off, all doors closed, rear door LH locked | 11 to 14 V | |||
| 2O-38 (LSWL) - Body ground*2, *4 | B - Body ground | Rear door unlock detection switch LH signal | Rear door LH unlocked | Below 1 V |
| Engine switch off, all doors closed, rear door LH locked | 11 to 14 V | |||
| G216-2 (LSWR) - Body ground*4 | V - Body ground | Rear door unlock detection switch RH signal | Rear door RH unlocked | Below 1 V |
| Engine switch off, all doors closed, rear door RH locked | 8 to 12 V | |||
| G218-17 (LSWB) - Body ground | SB - Body ground | Back door unlock detection switch signal | Back door unlocked | Below 1 V |
| Engine switch off, all doors closed, back door locked | 11 to 14 V | |||
| 2M-30 (BZR) - Body ground | GR - Body ground | Wireless door lock buzzer signal | Wireless door lock buzzer off | Below 1 V |
| Wireless door lock buzzer on | Pulse generation | |||
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
Disconnect the G215 certification ECU (smart key ECU assembly) connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G215-10 (+B) - Body ground | V - Body ground | Battery power supply | Always | 11 to 14 V |
| G215-11 (E) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the G215 certification ECU (smart key ECU assembly) connector.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G214-18 (RCO) - G215-11 (E) | L - W-B | Output to door control receiver
(Power supply for door control receiver. Certification ECU [smart key ECU assembly] outputs 5 V when receiver starts operating.) |
Proceed:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area 3.
Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed |
Pulse generation
(See waveform 1) |
| G214-19 (CSEL) - G215-11 (E) | P - W-B | Communication channel switching circuit | Proceed:
1.
Engine switch off 2.
All doors closed |
Below 1 V → Pulse generation |
| G214-20 (RDAM) - G215-11 (E) | G - W-B | Door control receiver verifies data received from electrical key transmitter sub-assembly.
Door control receiver sends data from electrical key transmitter sub-assembly to certification ECU (smart key ECU assembly) (Door control receiver intermittently grounds 12 V signal from certification ECU [smart key ECU assembly]). |
Proceed:
1.
Engine switch off 2.
All doors locked 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area 5.
Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed |
Pulse generation
(See waveform 2) |
| *a | Before lock or unlock switch of electrical key transmitter sub-assembly pressed |
| *b | After lock or unlock switch of electrical key transmitter sub-assembly pressed |
Using an oscilloscope, check waveform 1.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | G214-18 (RCO) - G215-11 (E) |
| Tool Setting | 2 V/DIV., 500 ms/DIV. |
| Condition | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area 3.
Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed |
| *a | Before lock or unlock switch of electrical key transmitter sub-assembly pressed |
| *b | After lock or unlock switch of electrical key transmitter sub-assembly pressed |
Using an oscilloscope, check waveform 2.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | G214-20 (RDAM) - G215-11 (E) |
| Tool Setting | 5 V/DIV., 500 ms/DIV. |
| Condition | Procedure:
1.
Engine switch off 2.
All doors locked 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area 5.
Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed |