Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM (except 5L-E) › from 2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0329511 THEFT DETERRENT SYSTEM(except 5L-E) C

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM(except 5L-E)  B2764  Short to GND in Intrusion Sensor Signal Circuit  


DESCRIPTION

The intrusion and tilt sensor (theft warning ultrasonic sensor) conducts self-diagnosis immediately after power is supplied to the sensor (when the theft deterrent system is set).

If short to ground is detected in the ISIF line, the main body ECU (multiplex network body ECU) stores this DTC.

DTC Code Detection Item DTC Detection Condition Trouble Area
B2764 Short to GND in Intrusion Sensor Signal Circuit
After normal/trouble signal is output from intrusion and tilt sensor (theft warning ultrasonic sensor) as result of self-diagnosis, following malfunctions are detected:
1.

ISIF line circuit is shorted to ground

2.

Reception of signals other than normal/trouble signal


·

Map light sub-assembly

·

Intrusion and tilt sensor (theft warning ultrasonic sensor)

·

Main body ECU (multiplex network body ECU)

·

Harness or connector



WIRING DIAGRAM

B490791E01
5.354,3.063 7.063,3.406 1.708,0.344 10 false Main Body ECU (Multiplex Network Body ECU) 5.365,2.896 5.938,3.135 0.573,0.24 10 false G216 5.625,2.167 6.198,2.406 0.573,0.24 10 false ISIF 5.375,2.167 5.948,2.406 0.573,0.24 10 false 12 6.323,1.76 6.896,2 0.573,0.24 10 false +B 1.146,3.198 1.719,3.438 0.573,0.24 10 false W7 1.24,3.375 3.25,3.573 2.01,0.198 10 false Map Light Assembly 1.75,0.875 3.635,1.219 1.885,0.344 10 false Intrusion and Tilt Sensor (Theft Warning Ultrasonic Sensor) 1.292,1.917 3.302,2.115 2.01,0.198 10 false GND3 3.781,1.625 4.333,1.823 0.552,0.198 10 false S+B 3.146,0.25 3.698,0.448 0.552,0.198 10 false ECU-B 1.229,0.094 2.156,0.271 0.927,0.177 10 false from Battery 3.771,2.198 4.323,2.396 0.552,0.198 10 false IOUT 4.188,2.188 4.74,2.385 0.552,0.198 10 false 6 4.177,1.635 4.729,1.833 0.552,0.198 10 false 7 1.125,1.917 1.677,2.115 0.552,0.198 10 false 5

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

w/ Entry and Start System:

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.



PROCEDURE

1.CHECK WAVEFORM (INTRUSION AND TILT SENSOR [THEFT WARNING ULTRASONIC SENSOR]) (IOUT)
a.

Using an oscilloscope, check the waveform.

B490792C01
2.281,0.542 2.625,0.792 0.344,0.25 2.594,1.208 3.01,0.719 true 1.833,2.938 1.708,2.792 true 2.365,2.938 2.24,2.792 true 1.021,0.406 1.333,0.563 0.313,0.156 10 false *a 1.531,2.688 1.844,2.844 0.313,0.156 10 false *b 2.042,2.708 2.354,2.865 0.313,0.156 10 false *c 3.927,2.74 4.24,2.896 0.313,0.156 10 false *d 3.938,3.208 4.25,3.365 0.313,0.156 10 false *e 2.083,3.313 2.396,3.469 0.313,0.156 10 false *f 2.406,3.302 2.708,3.573 0.302,0.271 10 false *g 2.583,3.698 2.896,3.854 0.313,0.156 10 false *h 1.458,4.177 1.771,4.385 0.313,0.208 10 false *i 3.927,4.188 4.281,4.479 0.354,0.292 10 false *j 3.094,0.625 3.583,0.896 0.49,0.271 10 false IOUT 2.354,0.583 2.844,0.854 0.49,0.271 10 false W7
*a Component with harness connected
(Map Light Assembly)
*b IOUT Initial Signal
*c IOUT Initial Response *d Approximately 1.0 seconds
*e Initial Diagnosis *f Approximately 1.0 to 1.6 seconds
*g Approximately 0.05 seconds *h Approximately 5.5 seconds
*i Disarmed State *j Arming Preparation State


Measurement Condition
Tester Connection Content
Tester Connection W7-6 (IOUT) - Body ground
Tool Setting 2 V/DIV., 100 ms./DIV.
Condition Theft deterrent system is set (system changes from disarmed state to arming preparation state)

HINT:
·

If the intrusion and tilt sensor (theft warning ultrasonic sensor) is normal, an initial response is output in response to the HI input from the main body ECU (multiplex network body ECU).

·

If the waveform output remains LO, there may be a problem with the main body ECU (multiplex network body ECU), as there is no input from the main body ECU (multiplex network body ECU).



OK:

The waveform displays properly (HI is 6.5 V or higher and LO is below 1 V).



Result:
Proceed to
OK
NG



OK

NG

2.CHECK VOLTAGE (INTRUSION AND TILT SENSOR [THEFT WARNING ULTRASONIC SENSOR]) (IOUT)
2.CHECK VOLTAGE (INTRUSION AND TILT SENSOR [THEFT WARNING ULTRASONIC SENSOR]) (IOUT)
a.
E140414C90
1.417,0.427 1.979,0.75 0.563,0.323 1.51,1.375 0.875,0.688 0.875,0.688 0.76,0.688 true 0.052,0.031 0.313,0.229 0.26,0.198 10 false *a 0.458,0.604 0.813,0.802 0.354,0.198 10 false IOUT 1.594,0.5 1.896,0.698 0.302,0.198 10 false W7
*a Front view of wire harness connector
(to Map Light Assembly)


Disconnect the map light assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition
W7-6 (IOUT) - Body ground Immediately after theft deterrent system set


Result:
Result Proceed to
IOUT voltage is below 1 V when theft deterrent system is set A
IOUT voltage is 6.5 V or higher when theft deterrent system is set B


HINT:

With connector W7 of the map light assembly disconnected, measure the voltage at IOUT when the theft deterrent system is set.




A

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - MAP LIGHT ASSEMBLY)

B

4.INSPECT MAP LIGHT ASSEMBLY
3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - MAP LIGHT ASSEMBLY)
a.

Disconnect the G216 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the W7 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G216-12 (ISIF) - W7-6 (IOUT) Always Below 1 Ω
G216-12 (ISIF) or W7-6 (IOUT) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MAP LIGHT ASSEMBLY

b.
B490793E01
1.521,1.458 1.948,1.729 0.427,0.271 1.521,0.354 1.948,0.625 0.427,0.271 1.74,0.948 2.125,0.521 2.125,0.521 2.229,0.521 true 1.917,2.25 2.448,2.927 2.448,2.927 2.552,2.927 true 0.958,1.677 1.073,1.677 1.073,1.677 1.802,2.156 true 2.063,2.188 2.51,1.635 2.51,1.635 2.615,1.635 true 1.865,1.021 2.188,1.281 2.188,1.281 2.292,1.281 true 1.115,0.75 1.229,0.75 1.229,0.75 1.573,0.99 true 1.688,0.427 1.844,0.625 0.156,0.198 10 false A 1.708,1.521 1.865,1.719 0.156,0.198 10 false B 2.354,1.188 2.823,1.396 0.469,0.208 10 false GND 2.667,1.563 3.135,1.771 0.469,0.208 10 false GND 0.802,0.677 1.271,0.885 0.469,0.208 10 false S+B 2.302,0.448 2.771,0.656 0.469,0.208 10 false IOUT 2.615,2.833 3.083,3.042 0.469,0.208 10 false IOUT 0.656,1.604 1.125,1.813 0.469,0.208 10 false S+B

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 (GND) - B-5 (GND) Always Below 1 Ω
A-2 (IOUT) - B-6 (IOUT) Always Below 1 Ω
A-4 (S+B) - B-7 (S+B) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE INTRUSION AND TILT SENSOR (THEFT WARNING ULTRASONIC SENSOR)

NG