Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM (except 5L-E) › from 2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0329511 THEFT DETERRENT SYSTEM(except 5L-E) J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM(except 5L-E)  Tilt Sensor Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) communicates with the tilt sensor (theft warning ultrasonic sensor) via the ISIF communication line. The tilt sensor (theft warning ultrasonic sensor) sends information regarding changes in the vehicle tilt angle to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) checks whether the vehicle body is being tilted without authorization.

HINT:

In the following situations, the tilt sensor (theft warning ultrasonic sensor) may operate and cause the theft deterrent system to operate even when the sensor is normal.

·

The vehicle is transported by a ferry, trailer or train.

·

The vehicle is parked in a multi-story parking facility.

·

The vehicle is washed by an automatic car wash.

·

A tire blows out.

·

The vehicle is jacked up for a tire or wheel change.

·

An earthquake occurs or the road subsides.

·

Goods such as skis or snowboards are loaded or unloaded.



WIRING DIAGRAM

B490791E02
5.354,3.063 7.063,3.406 1.708,0.344 10 false Main Body ECU (Multiplex Network Body ECU) 5.365,2.896 5.938,3.135 0.573,0.24 10 false G216 5.625,2.167 6.198,2.406 0.573,0.24 10 false ISIF 5.375,2.167 5.948,2.406 0.573,0.24 10 false 12 6.323,1.76 6.896,2 0.573,0.24 10 false +B 1.146,3.198 1.719,3.438 0.573,0.24 10 false W7 1.24,3.375 3.25,3.573 2.01,0.198 10 false Map Light Assembly 1.844,0.896 3.49,1.25 1.646,0.354 10 false Tilt Sensor (Theft Warning Ultrasonic Sensor) 1.292,1.917 3.302,2.115 2.01,0.198 10 false GND3 3.781,1.625 4.333,1.823 0.552,0.198 10 false S+B 3.146,0.25 3.698,0.448 0.552,0.198 10 false ECU-B 1.229,0.094 2.156,0.271 0.927,0.177 10 false from Battery 3.771,2.198 4.323,2.396 0.552,0.198 10 false IOUT 4.188,2.188 4.74,2.385 0.552,0.198 10 false 6 4.177,1.635 4.729,1.833 0.552,0.198 10 false 7 1.125,1.917 1.677,2.115 0.552,0.198 10 false 5

CAUTION / NOTICE / HINT

NOTICE:
·

w/ Entry and Start System:

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.READ VALUE USING GTS (Intrusion Sensor)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

NOTICE:
B490799C01
1.021,0.896 1.396,0.375 1.396,0.375 1.49,0.375 true 2.438,0.885 2.813,0.365 2.813,0.365 2.906,0.365 true 1.01,1.042 1.552,1.979 1.552,1.979 1.646,1.979 true 2.396,1.031 2.938,1.969 2.938,1.969 3.031,1.969 true 0.104,0.135 0.417,0.333 0.313,0.198 10 false *1 1.5,0.292 1.813,0.49 0.313,0.198 10 false *a 2.958,0.292 3.271,0.49 0.313,0.198 10 false *a 1.677,1.896 1.99,2.094 0.313,0.198 10 false *b 3.083,1.885 3.396,2.083 0.313,0.198 10 false *b
*1 Map Light Assembly
*a Intrusion Sensor (Theft Warning Ultrasonic Sensor)
*b Tape


·

Be sure to cover the 2 intrusion sensors (theft warning ultra sonic sensor) in the map light assembly with tape to prevent detected by the intrusion sensor.

·

After setting the theft deterrent system, wait at least 30 seconds (until the vehicle is in the armed state), tilt the vehicle (jack up the vehicle so that the tires are in the air) and check the Data List.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM (except 5L-E)>SYSTEM DESCRIPTION



HINT:

When performing the above inspection, have the electrical key transmitter in the vehicle exterior detection area to perform certification (this prevents the alarm from sounding).*

*: Entry and Start System



Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Intrusion Sensor Status of the tilt sensor detection ON or OFF ON: Change in pitch angle detected
OFF: Both of the conditions below is met
·

No moving object detected by sensor

·

Vehicle tilt not detected by sensor


-

OK:

The GTS display changes correctly in response to the detection condition of the tilt sensor (theft warning ultrasonic sensor).



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK WAVEFORM (TILT SENSOR [THEFT WARNING ULTRASONIC SENSOR]) (IOUT)
2.CHECK WAVEFORM (TILT SENSOR [THEFT WARNING ULTRASONIC SENSOR]) (IOUT)
a.

Using an oscilloscope, check the waveform.

B490792C01
2.281,0.542 2.625,0.792 0.344,0.25 2.594,1.208 3.01,0.719 true 1.833,2.938 1.708,2.792 true 2.365,2.938 2.24,2.792 true 1.021,0.406 1.333,0.563 0.313,0.156 10 false *a 1.531,2.688 1.844,2.844 0.313,0.156 10 false *b 2.042,2.708 2.354,2.865 0.313,0.156 10 false *c 3.927,2.74 4.24,2.896 0.313,0.156 10 false *d 3.938,3.208 4.25,3.365 0.313,0.156 10 false *e 2.083,3.313 2.396,3.469 0.313,0.156 10 false *f 2.406,3.302 2.708,3.573 0.302,0.271 10 false *g 2.583,3.698 2.896,3.854 0.313,0.156 10 false *h 1.458,4.177 1.771,4.385 0.313,0.208 10 false *i 3.927,4.188 4.281,4.479 0.354,0.292 10 false *j 3.094,0.625 3.583,0.896 0.49,0.271 10 false IOUT 2.354,0.583 2.844,0.854 0.49,0.271 10 false W7
*a Component with harness connected
(Map Light Assembly)
*b IOUT Initial Signal
*c IOUT Initial Response *d Approximately 1.0 second
*e Initial Diagnosis *f Approximately 1.0 to 1.6 seconds
*g Approximately 0.05 seconds *h Approximately 5.5 seconds
*i Disarmed State *j Arming Preparation State


Measurement Condition
Tester Connection Content
Tester Connection W-6 (IOUT) - Body ground
Tool Setting 2 V/DIV., 100 ms./DIV.
Condition Theft deterrent system is set (system changes from disarmed state to arming preparation state)

HINT:
·

If the tilt sensor (theft warning ultrasonic sensor) is normal, an initial response is output in response to the HI input from the main body ECU (multiplex network body ECU).

·

If the waveform output remains LO, there may be a problem with the main body ECU (multiplex network body ECU), as there is no input from the main body ECU (multiplex network body ECU).



OK:

The waveform displays properly (HI is 6.5 V or higher and LO is below 1 V).



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - MAP LIGHT ASSEMBLY)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - MAP LIGHT ASSEMBLY)
a.

Disconnect the G216 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the W7 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G216-12 (ISIF) - W7-6 (IOUT) Always Below 1 Ω
G216-12 (ISIF) or W7-6 (IOUT) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT MAP LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MAP LIGHT ASSEMBLY

b.
B490793E01
1.521,1.458 1.948,1.729 0.427,0.271 1.521,0.354 1.948,0.625 0.427,0.271 1.74,0.948 2.125,0.521 2.125,0.521 2.229,0.521 true 1.917,2.25 2.448,2.927 2.448,2.927 2.552,2.927 true 0.958,1.677 1.073,1.677 1.073,1.677 1.802,2.156 true 2.063,2.188 2.51,1.635 2.51,1.635 2.615,1.635 true 1.865,1.021 2.188,1.281 2.188,1.281 2.292,1.281 true 1.115,0.75 1.229,0.75 1.229,0.75 1.573,0.99 true 1.688,0.427 1.844,0.625 0.156,0.198 10 false A 1.708,1.521 1.865,1.719 0.156,0.198 10 false B 2.354,1.188 2.823,1.396 0.469,0.208 10 false GND 2.667,1.563 3.135,1.771 0.469,0.208 10 false GND 0.802,0.677 1.271,0.885 0.469,0.208 10 false S+B 2.302,0.448 2.771,0.656 0.469,0.208 10 false IOUT 2.615,2.833 3.083,3.042 0.469,0.208 10 false IOUT 0.656,1.604 1.125,1.813 0.469,0.208 10 false S+B

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 (GND) - B-5 (GND) Always Below 1 Ω
A-2 (IOUT) - B-6 (IOUT) Always Below 1 Ω
A-4 (S+B) - B-7 (S+B) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE TILT SENSOR (THEFT WARNING ULTRASONIC SENSOR)

NG