Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (for Halogen Headlight) › from 2017.08
RM27T0E _59 Vehicle Exterior _053747 LIGHTING (EXT) _0326211 LIGHTING SYSTEM(for Halogen Headlight) J

LIGHTING (EXT)  LIGHTING SYSTEM(for Halogen Headlight)  Hazard Warning Switch Circuit  


DESCRIPTION

The combination meter assembly receives the hazard warning signal switch assembly ON signal and controls the operation of the hazard warning lights.

WIRING DIAGRAM

E346682E07
5.344,1.375 5.958,1.573 0.615,0.198 10 false HZSW 5.885,1.448 6.5,1.646 0.615,0.198 10 false I/F 6.448,1.469 7.063,1.667 0.615,0.198 10 false CPU 5.125,1.375 5.74,1.573 0.615,0.198 10 false 7 2.427,1.375 3.042,1.573 0.615,0.198 10 false 8 0.771,1.385 1.385,1.583 0.615,0.198 10 false 4 1.01,1.396 1.625,1.594 0.615,0.198 10 false GND 2,1.385 2.615,1.583 0.615,0.198 10 false HAZ 0.854,1.969 2.938,2.469 2.083,0.5 10 false G23 0.854,2.135 3.323,2.531 2.469,0.396 10 false Integration Control and Panel Assembly (Hazard Warning Signal Switch) 5.26,2.458 7.125,2.917 1.865,0.458 10 false G304 5.25,2.615 7.125,3.083 1.875,0.469 10 false Combination Meter Assembly

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not


PROCEDURE

1.READ VALUE USING GTS
a.

Using the GTS, read the Data List.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for Halogen Headlight)>DATA LIST / ACTIVE TEST

Combination Meter
Tester Display Measurement Item / Range Control Range Diagnostic Note
Hazard Flasher Switch Integration control and panel assembly (hazard warning signal switch) / OFF or ON OFF: Integration control and panel assembly (hazard warning signal switch) off
ON: Integration control and panel assembly (hazard warning signal switch) on
-

OK:

Normal condition listed above are displayed.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT INTEGRATION CONTROL AND PANEL ASSEMBLY
2.INSPECT INTEGRATION CONTROL AND PANEL ASSEMBLY
a.

Remove the integration control and panel assembly (hazard warning signal switch).

Click hereVehicle Exterior>LIGHTING (EXT)>HAZARD WARNING SWITCH>REMOVAL


b.

Inspect the integration control and panel assembly (hazard warning signal switch).

Click hereVehicle Exterior>LIGHTING (EXT)>HAZARD WARNING SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HAZARD WARNING SIGNAL SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY AND BODY GROUND)

NG

REPLACE INTEGRATION CONTROL AND PANEL ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (HAZARD WARNING SIGNAL SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the G23 hazard warning signal switch assembly connector.


b.

Disconnect the G304 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G23-8 (HAZ) - G304-7 (HZSW) Always Below 1 Ω
G23-4 (GND) - Body ground Always Below 1 Ω
G23-8 (HAZ) or G304-7 (HZSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR