Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM (except 5L-E) › from 2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0329511 THEFT DETERRENT SYSTEM(except 5L-E) J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM(except 5L-E)  Security Indicator Light Circuit  


DESCRIPTION

When the theft deterrent system is in the disarmed state, the security indicator light will blink if the immobiliser system is set, or not illuminate if the immobiliser system is not set.

When the theft deterrent system is in the armed state, the security indicator light blinks.

When the theft deterrent system is in the arming preparation state or alarm sounding state, the security indicator light illuminates.

WIRING DIAGRAM

E375269E03
5.208,4.594 6.854,4.927 1.646,0.333 10 false Main Body ECU (Multiplex Network Body ECU) 5.417,1.927 6.563,2.281 1.146,0.354 10 false Transponder Key ECU Assembly 1.448,4.563 3.271,4.958 1.823,0.396 10 false Security Indicator Light Assembly 5.24,4.385 5.677,4.583 0.438,0.198 10 false G218 5.229,0.875 5.667,1.073 0.438,0.198 10 false 8 5.448,3.448 5.885,3.646 0.438,0.198 10 false IND 2.896,3.448 3.333,3.646 0.438,0.198 10 false LP 3.198,3.448 3.635,3.646 0.438,0.198 10 false 2 1.354,4.385 1.792,4.583 0.438,0.198 10 false H23 5.354,1.771 5.792,1.969 0.438,0.198 10 false G74 5.188,3.448 5.625,3.646 0.438,0.198 10 false 15 5.438,0.885 5.875,1.083 0.438,0.198 10 false IND 6.219,3.115 6.656,3.313 0.438,0.198 10 false +B 1.521,3.458 1.958,3.656 0.438,0.198 10 false E 1.333,3.448 1.771,3.646 0.438,0.198 10 false 5

CAUTION / NOTICE / HINT

NOTICE:
·

Before performing the inspection, check "Security Indicator Light Does not Blink" in ENGINE IMMOBILISER SYSTEM.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)>Security Indicator Light Does not Blink

·

w/ Entry and Start System:

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (Security Indicator)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

According to the display on the GTS, perform the Active Test.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Control Range Diagnostic Note
Security Indicator Security indicator light ON or OFF -

OK:

Security indicator illuminates when operated through the GTS.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
2.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the H23 security indicator light assembly connector.


b.

Disconnect the G218 main body ECU (multiplex network body ECU) connector.


c.

Disconnect the G74 transponder key ECU assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H23-2 (LP) - G218-15 (IND) Always Below 1 Ω
H23-2 (LP) or G218-15 (IND) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR