Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2017.08
RM27T0E _51 Engine / Hybrid System _053657 1GR-FE ENGINE CONTROL _0260436 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P2444  Secondary Air Injection System Pump Stuck On Bank1  P2445  Secondary Air Injection System Pump Stuck Off Bank1  


DESCRIPTION

Refer to P0412 (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P0412).

DTC No. DTC Detection Condition Trouble Area
P2444 Secondary air pressure is higher than 2.5 kPa (19 mmHg) despite the ECM commanding the air pump to turn off (2 trip detection logic).
·

Short in air pump circuit

·

Open or short in pressure sensor circuit

·

Pressure sensor

·

Air injection control driver

·

ECM


P2445 Secondary air pressure is below 1 kPa (8 mmHg) despite the ECM commanding the air pump to turn on (2 trip detection logic).
·

Air pump assembly

·

Open in air pump circuit

·

Air injection system piping

·

Pressure sensor

·

Open or short in pressure sensor circuit

·

Air injection control driver

·

ECM

·

Open or short in air pump heater circuit

·

AIR PMP HTR relay


When secondary air injection is turned from off to on, the change in the secondary air injection pressure is less than 5 kPa (2 trip detection logic).

MONITOR DESCRIPTION

The ECM monitors the pressure in the secondary air passage using the pressure sensor located on the emission control valve set of the secondary air injection system. The sensor measures the pressure in the secondary air passage and transmits a signal to the ECM.

If a malfunction is detected, the ECM illuminates the MIL and stores a DTC.

Example:

·

DTC P2444 mainly indicates a malfunction in which the air pump is stuck on.

·

DTC P2445 mainly indicates a malfunction in which the air pump is stuck off.


WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

By using the GTS to perform the Secondary Air Injection Check operation in the System Check, the air-fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions. Furthermore, pending codes also can be checked by performing Utility / Secondary Air Injection Check / Automatic Mode after the repair.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2444 AND/OR P2445)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result
Result Proceed to
P2444 and/or P2445 is output A
P2444 and/or P2445 and P0418 are output B
P2444 and/or P2445 and other DTCs (except P0418) are output C

HINT:

If any DTCs other than P0418, P2444 and P2445 are output, troubleshoot those DTCs first.




A

2.CHECK FREEZE FRAME DATA (AIR PUMP FREEZE, AIR SWITCHING VALVE FREEZEAND AIR SWITCHING VALVE2 FREEZE)

B

GO TO AIR PUMP INSPECTION PROCEDURE

C

2.CHECK FREEZE FRAME DATA (AIR PUMP FREEZE, AIR SWITCHING VALVE FREEZEAND AIR SWITCHING VALVE2 FREEZE)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Read the values of Air Pump Freeze, Air Switching Valve Freeze and Air Switching Valve2 Freeze from the freeze frame data recorded previously.


d.

Referring to the following table, proceed to the appropriate step according to the result of the data reading.

Result
Result Proceed to
Air Pump Freeze Air Switching Valve Freeze Air Switching Valve2 Freeze
OFF OFF OFF B
Except above A



A

3.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE AIR PUMP HEATER)

B

7.PERFORM ACTIVE TEST USING GTS (SECONDARY AIR INJECTION SYSTEM OPERATION)
3.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE AIR PUMP HEATER)
a.
U169184E01
0.158,0.027 0.339,0.227 0.181,0.200 10 *a 1.608,0.08 1.896,0.243 0.288,0.163 10 A18 1.608,0.887 0.836,1.559 false 0.394,1.543 0.841,1.734 0.448,0.191 10 APH+

Disconnect the air pump connector.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG) and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT/ Active Test / Activate the Air Pump Heater.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A18-1 (APH+) - Body ground Activate the Air Pump Heater is ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Air Pump Assembly)


f.

Reconnect the air pump connector.



OK

4.INSPECT AIR PUMP ASSEMBLY (HEATER RESISTANCE)

NG

5.INSPECT NO. 1 INTEGRATION RELAY (AIR PMP HTR RELAY)
4.INSPECT AIR PUMP ASSEMBLY (HEATER RESISTANCE)

OK

5.INSPECT NO. 1 INTEGRATION RELAY (AIR PMP HTR RELAY)

NG

5.INSPECT NO. 1 INTEGRATION RELAY (AIR PMP HTR RELAY)
a.

Inspect the No. 1 integration relay (AIR PMP HTR relay) (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).



OK

6.CHECK HARNESS AND CONNECTOR (AIR PUMP - NO. 1 INTEGRATION RELAY, BODY GROUND)

NG

REPLACE NO. 1 INTEGRATION RELAY

6.CHECK HARNESS AND CONNECTOR (AIR PUMP - NO. 1 INTEGRATION RELAY, BODY GROUND)
a.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


b.

Disconnect the air pump connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
1T-12 - A18-1 (APH+) Always Below 1 Ω
A18-3 (APHG) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
1T-12 or A18-1 (APH+) - Body ground Always 10 kΩ or higher



d.

Reinstall the No. 1 integration relay.


e.

Reconnect the air pump connector.



OK

7.PERFORM ACTIVE TEST USING GTS (SECONDARY AIR INJECTION SYSTEM OPERATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.PERFORM ACTIVE TEST USING GTS (SECONDARY AIR INJECTION SYSTEM OPERATION)
a.

Start the engine and warm it up.


b.

Turn the engine switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the engine switch on (IG).


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV1: OPEN, ASV2: OPEN and AIR PUMP: OFF, ASV1: CLOSE, ASV2: CLOSE.

HINT:

When Manual Mode is selected, the GTS initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.



g.

Start the engine.


h.

Perform the secondary air injection system forced operation while the engine is idling.


i.

Check that the Data List values for the air pump (AIR PUMP), emission control valve (ASV) and pressure in the secondary air injection system passage (PRESSURE) displayed on the GTS are as shown in the table below.

Standard:
GTS Operation Air Pump Emission Control Valve PRESSURE*
AIR PUMP: ON, ASV: OPEN ON OPEN 1 kPa or higher [A]
AIR PUMP: OFF, ASV: CLOSE OFF CLOSE Below 2.5 kPa [B]


*: Average pumping pressure. The pressure should be 1 kPa or higher when the secondary air injection system operates.

Standard:

The pressures for [A] and [B] should differ by 1 kPa or more.



j.

Turn the engine switch off.

NOTICE:
·

This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While secondary air injection system operation using the GTS is prohibited, the GTS display indicates the prohibition (WAIT or ERROR). If ERROR is displayed on the GTS during the test, stop the engine for 10 minutes, and then try again.

·

Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the engine switch turned to on (IG) or the engine running.

·

Turn the engine switch off when the Secondary Air Injection Check operation finishes.





OK

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P2444 AND/OR P2245)

NG

9.INSPECT EMISSION CONTROL VALVE SET (PRESSURE SENSOR)
8.CHECK WHETHER DTC OUTPUT RECURS (DTC P2444 AND/OR P2245)
a.

Start the engine and warm it up.


b.

Turn the engine switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the engine switch on (IG).


e.

Turn the GTS on.



g.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.


h.

Start the engine after the GTS initialization is finished.


i.

Perform the System Check operation by pressing ENTER (Next).


j.

Perform the following to confirm the secondary air injection system pending codes: Press the Exit button.


k.

Check for pending DTCs.


l.

Turn the engine switch off.

NOTICE:
·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the engine switch turned to on (IG) or the engine running.

·

Turn the engine switch off when the Secondary Air Injection Check operation finishes.



Result
Result Proceed to
P2444 and/or P2445 is output A
No pending DTC is output B



A

9.INSPECT EMISSION CONTROL VALVE SET (PRESSURE SENSOR)

B

9.INSPECT EMISSION CONTROL VALVE SET (PRESSURE SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Air Pump Pressure (Absolute) and Air Pump2 Pressure (Absolute).


e.

Check the pressure displayed on the GTS.

Standard pressure:

45 to 135 kPa


HINT:

The GTS displays the air pump pressure as absolute pressure.


Result
Result Proceed to
OK A
NG (for Bank 1) B
NG (for Bank 2) C



A

10.CHECK AIR INJECTION SYSTEM PIPE CONNECTIONS

B

C

10.CHECK AIR INJECTION SYSTEM PIPE CONNECTIONS
A221586

a.

Check that all the pipes and hoses between the air pump and emission control valve are securely connected.


b.

Inspect the pipes and hoses for blockages and damage.

OK:

Secondary air injection system piping has no blockages or damage.




OK

11.CHECK HARNESS AND CONNECTOR (AIR INJECTION CONTROL DRIVER POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE AIR INJECTION SYSTEM PIPING

11.CHECK HARNESS AND CONNECTOR (AIR INJECTION CONTROL DRIVER POWER SOURCE CIRCUIT)
U169185E01
1.554,0.284 1.842,0.447 0.288,0.163 10 A17 1.529,2.264 1.817,2.427 0.288,0.163 10 A16 0.617,1.918 1.162,2.095 0.545,0.177 10 BATT 1.408,1.349 0.875,1.869 false 0.94,3.861 1.068,4.038 0.128,0.177 10 E 2.373,3.861 2.616,4.038 0.242,0.177 10 +B 2.059,3.293 2.414,3.861 false 1.172,3.287 1.015,3.831 false 0.172,0.096 0.376,0.308 0.204,0.211 10 *a

a.

Disconnect the air injection control driver connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A16-1 (E) - Body ground Always Below 1 Ω



c.

Turn the engine switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A17-1 (BATT) - Body ground Always 11 to 14 V (near battery voltage)
A16-5 (+B) - Body ground Engine switch on (IG) 11 to 14 V (near battery voltage)



Text in Illustration
*a Front view of wire harness connector
(to Air Injection Control Driver)

e.

Reconnect the air injection control driver connectors.



OK

12.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER)

NG

REPAIR OR REPLACE AIR INJECTION CONTROL DRIVER POWER SOURCE CIRCUIT

12.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER)
a.

Disconnect the ECM connector.


b.

Disconnect the air injection control driver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C36-18 (AIRP) - A16-4 (SIP) Always Below 1 Ω
C36-18 (AIRP) or A16-4 (SIP) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reconnect the air injection control driver connector.



OK

13.CHECK AIR PUMP ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK AIR PUMP ASSEMBLY

OK

16.PERFORM ACTIVE TEST USING GTS

NG

14.REPLACE AIR PUMP ASSEMBLY
14.REPLACE AIR PUMP ASSEMBLY

NEXT

15.CHECK WHETHER DTC OUTPUT RECURS (DTC P2444, P2445 AND/OR P2447)
15.CHECK WHETHER DTC OUTPUT RECURS (DTC P2444, P2445 AND/OR P2447)
a.

Start the engine and warm it up.


b.

Turn the engine switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the engine switch on (IG).


e.

Turn the GTS on.



g.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air injection check / Automatic Mode.


h.

Start the engine after the GTS initialization is finished.


i.

Perform the System Check operation by pressing ENTER (Next).


j.

Perform the following to confirm the secondary air injection system pending codes: Press the Exit button.


k.

Check for pending DTCs.

OK:

No pending DTC is output.



l.

Turn the engine switch off.

NOTICE:
·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the engine switch turned to on (IG) or the engine running.

·

Turn the engine switch off when the Secondary Air Injection Check operation finishes.





OK

END

NG

16.PERFORM ACTIVE TEST USING GTS
16.PERFORM ACTIVE TEST USING GTS
a.

Disconnect the air injection control driver connector.


U147661E03
1.375,2.604 1.177,3.094 false 1.542,2.615 1.5,3.094 false 1.677,2.615 1.938,3.094 false 1.813,2.615 2.281,3.104 false 0.646,2.479 0.906,2.656 0.26,0.177 10 false A16 0.979,1.844 1.219,2.021 0.24,0.177 10 false *a 1.094,3.115 1.281,3.292 0.188,0.177 10 false E 1.448,3.115 1.656,3.292 0.208,0.177 10 false DI 1.875,3.125 2.271,3.302 0.396,0.177 10 false SIV 2.302,3.115 2.708,3.292 0.406,0.177 10 false SIP 2.531,0.063 2.771,0.24 0.24,0.177 10 false *2 0.667,0.208 0.906,0.385 0.24,0.177 10 false *1 2.448,0.771 2.885,0.948 0.438,0.177 10 false AIDI 2.448,1.125 2.896,1.302 0.448,0.177 10 false AIRV 0.865,0.771 1.073,0.948 0.208,0.177 10 false DI 0.781,1.125 1.177,1.302 0.396,0.177 10 false SIV

b.

Connect terminals DI and SIV of the wire harness connector for the air injection control driver.

Text in Illustration
*1 Air Injection Control Driver
*2 ECM
*a Front view of wire harness connector
(to Air Injection Control Driver)


c.

Connect the GTS to the DLC3.


d.

Turn the engine switch on (IG) and turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV 1: OPEN, ASV 2: OPEN.

HINT:

When Manual Mode is selected, the GTS initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.



f.

Start the engine.


g.

Perform the secondary air injection system forced operation while the engine is idling.


h.

Measure the voltage between the SIV and E terminals of the ECM connector when the secondary air injection system is ON and OFF.


i.

Turn the engine switch off.

NOTICE:
·

Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the engine switch turned to on (IG) or the engine running.

·

Turn the engine switch off when the Secondary Air Injection Check operation finishes.



Standard Voltage:
Tester Connection Condition Specified Condition
A16-3 (SIV) - A16-1 (E) AIR PUMP: ON, ASV: OPEN 0.5 to 2 V
A16-3 (SIV) - A16-1 (E) AIR PUMP: OFF, ASV: CLOSE 11 to 14 V



U147662E03
1.396,2.625 1.198,3.115 false 1.531,2.615 1.49,3.094 false 1.667,2.615 1.927,3.094 false 1.813,2.615 2.281,3.104 false 0.625,2.479 0.885,2.656 0.26,0.177 10 false A16 0.979,1.844 1.219,2.021 0.24,0.177 10 false *a 1.125,3.125 1.313,3.302 0.188,0.177 10 false E 1.448,3.125 1.656,3.302 0.208,0.177 10 false DI 1.885,3.125 2.281,3.302 0.396,0.177 10 false SIV 2.292,3.115 2.698,3.292 0.406,0.177 10 false SIP 2.531,0.063 2.771,0.24 0.24,0.177 10 false *2 0.667,0.208 0.906,0.385 0.24,0.177 10 false *1 2.448,0.76 2.896,0.938 0.448,0.177 10 false AIDI 2.448,1.135 2.906,1.313 0.458,0.177 10 false AIRP 0.865,0.771 1.073,0.948 0.208,0.177 10 false DI 0.781,1.125 1.177,1.302 0.396,0.177 10 false SIP

j.

Connect terminals DI and SIP of the wire harness connector for the air injection control driver.

Text in Illustration
*1 Air Injection Control Driver
*2 ECM
*a Front view of wire harness connector
(to Air Injection Control Driver)


k.

Connect the GTS to the DLC3.


l.

Turn the engine switch on (IG) and turn the GTS on.


m.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV 1: OPEN, ASV 2: OPEN.

HINT:

When Manual Mode is selected, the GTS initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.



n.

Start the engine.


o.

Perform the secondary air injection system forced operation while the engine is idling.


p.

Measure the voltage between the SIP and E terminals of the ECM connector when the secondary air injection system is ON and OFF.


q.

Turn the engine switch off.

NOTICE:
·

Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the engine switch turned to on (IG) or the engine running.

·

Turn the engine switch off when the Secondary Air Injection Check operation finishes.



Standard Voltage:
Tester Connection Condition Specified Condition
A16-4 (SIP) - A16-1 (E) AIR PUMP: ON, ASV: OPEN 0.5 to 2 V
A16-4 (SIP) - A16-1 (E) AIR PUMP: OFF, ASV: CLOSE 11 to 14 V



r.

Reconnect the air injection control driver connector.



OK

17.REPLACE AIR INJECTION CONTROL DRIVER

NG

17.REPLACE AIR INJECTION CONTROL DRIVER
a.

Replace the air injection control driver (See page Engine / Hybrid System>1GR-FE (EMISSION CONTROL)>AIR INJECTION DRIVER>REMOVAL).



NEXT

18.CHECK WHETHER DTC OUTPUT RECURS (DTC P2444, P2445 AND/OR P2447)
18.CHECK WHETHER DTC OUTPUT RECURS (DTC P2444, P2445 AND/OR P2447)
a.

Start the engine and warm it up.


b.

Turn the engine switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the engine switch on (IG).


e.

Turn the GTS on.



g.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air injection check / Automatic Mode.


h.

Start the engine after the GTS initialization is finished.


i.

Perform the System Check operation by pressing ENTER (Next).


j.

Perform the following to confirm the secondary air injection system pending codes: Press the Exit button.


k.

Check for pending DTCs.

OK:

No pending DTC is output.



l.

Turn the engine switch off.

NOTICE:
·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the engine switch turned to on (IG) or the engine running.

·

Turn the engine switch off when the Secondary Air Injection Check operation finishes.





OK

END

NG