Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2017.08
RM27T0E _51 Engine / Hybrid System _053657 1GR-FE ENGINE CONTROL _0260436 SFI SYSTEM J

1GR-FE ENGINE CONTROL  SFI SYSTEM  Starter Signal Circuit  


DESCRIPTION

While the engine is being cranked, current flows from terminal STAR of the certification ECU (smart key ECU assembly) to the park/neutral position switch (for automatic transmission) or clutch start switch (for manual transmission) and also flows to terminal STA of the ECM (STA Signal).

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following inspection procedure.


HINT:

This chart is based on the premise that the engine can crank normally. If the engine cannot crank normally, proceed to the problem symptoms table (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>PROBLEM SYMPTOMS TABLE).


PROCEDURE

1.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.


e.

Read the value.

OK:
Engine Switch Position Starter Signal
ON OFF
START ON




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK STARTER RELAY (ST RELAY) (POWER SOURCE)
2.CHECK STARTER RELAY (ST RELAY) (POWER SOURCE)
a.
A413212E01
0.156,0.104 0.469,0.302 0.313,0.198 10 false *1 0.417,0.938 0.729,1.135 0.313,0.198 10 false *2

Remove the ST relay from the engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
ST relay terminal 5 - Body ground Engine cranking 11 to 14 V


HINT:

The engine does not crank because the relay is not installed.


Result
Result Proceed to
OK A
NG for Manual transmission B
for Automatic transmission C

Text in Illustration
*1 Engine Room Relay Block and junction block assembly
*2 ST relay


c.

Reinstall the ST relay.



A

3.INSPECT ST RELAY

B

5.CHECK HARNESS AND CONNECTOR (ST RELAY - CLUTCH START SWITCH)

C

8.CHECK HARNESS AND CONNECTOR (ST RELAY - PARK/NEUTRAL POSITION SWITCH)
3.INSPECT ST RELAY

OK

4.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)

NG

REPLACE ST RELAY

4.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)
a.

Remove the ST relay from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST relay terminal 1 - Body ground Always Below 1 Ω



c.

Reinstall the ST relay.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - CLUTCH PEDAL SWITCH OR PARK/NEUTRAL POSITION SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ST RELAY - BODY GROUND)

5.CHECK HARNESS AND CONNECTOR (ST RELAY - CLUTCH START SWITCH)
a.

Remove the ST relay from the engine room relay block and junction block assembly.


b.

Disconnect the clutch start switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
ST relay terminal 2 - A40-1 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
ST relay terminal 2 or A40-1 - Body ground Always 10 kΩ or higher



d.

Reinstall the ST relay.


e.

Reconnect the clutch start switch connector.



OK

6.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ST RELAY - CLUTCH START SWITCH)

6.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the clutch start switch connector.


b.

Disconnect the certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A40-2 - G213-10 (STAR) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A40-2 or G213-10 (STAR) - Body ground Always 10 kΩ or higher



d.

Reconnect the clutch start switch connector.


e.

Reconnect the certification ECU (smart key ECU assembly) connector.



OK

7.INSPECT CLUTCH START SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (CLUTCH START SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

7.INSPECT CLUTCH START SWITCH ASSEMBLY
a.

Inspect the clutch start switch assembly (See page Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION).



OK

NG

REPLACE CLUTCH START SWITCH ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (ST RELAY - PARK/NEUTRAL POSITION SWITCH)
a.

Remove the ST relay from the engine room relay block and junction block assembly.


b.

Disconnect the park/neutral position switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
ST relay terminal 2 - C159-5 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
ST relay terminal 2 or C159-5 - Body ground Always 10 kΩ or higher



d.

Reinstall the ST relay.


e.

Reconnect the park/neutral position switch connector.



OK

9.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ST RELAY - PARK/NEUTRAL POSITION SWITCH)

9.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the park/neutral position switch connector.


b.

Disconnect the certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C159-4 - G213-10 (STAR) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C159-4 or G213-10 (STAR) - Body ground Always 10 kΩ or higher



d.

Reconnect the park/neutral position switch connector.


e.

Reconnect the certification ECU (smart key ECU assembly) connector.



OK

10.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

10.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly (See page Drivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION).



OK

NG