Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2017.08
RM27T0E _51 Engine / Hybrid System _053657 1GR-FE ENGINE CONTROL _0260436 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM. If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle is driven at 20 km/h (12.4 mph) for over 20 seconds.

DTC No. DTC Detection Condition Trouble Area
P0617 Conditions (a), (b) and (c) are met, and a positive (+B) battery voltage of 10.5 V or higher is applied to the ECM for 20 seconds (1 trip detection logic).

(a) The vehicle speed is 20 km/h (12.4 mph) or more.

(b) The engine speed is 1000 rpm or more.

(c) The STA signal is on.


·

Park/neutral position switch assembly

·

Clutch pedal switch assembly

·

Starter relay circuit

·

ECM



WIRING DIAGRAM

for Automatic Transmission
A413213E02
0.927,0.844 1.24,1.042 0.313,0.198 10 false NE 0.76,1.531 1.375,1.729 0.615,0.198 10 false STAR 0.854,3.115 1.313,3.313 0.458,0.198 10 false STA 0.25,3.938 0.865,4.135 0.615,0.198 10 false G213 0.25,4.125 2.094,4.51 1.844,0.385 10 false Certification ECU (Smart Key ECU Assembly) 6.115,0.854 6.573,1.052 0.458,0.198 10 false G56 6.188,0.656 6.5,0.854 0.313,0.198 10 false 13 1.26,0.729 1.479,0.927 0.219,0.198 10 false 14 1.25,1.417 1.563,1.615 0.313,0.198 10 false 10 1.271,3.01 1.583,3.208 0.313,0.198 10 false 12 6.146,1.542 6.604,1.74 0.458,0.198 10 false C34 6.208,1.354 6.521,1.552 0.313,0.198 10 false 23 6.458,0.833 6.917,1.031 0.458,0.198 10 false NEO 6.469,1.531 6.927,1.729 0.458,0.198 10 false NSW 5.188,4.625 5.802,4.823 0.615,0.198 10 false C159 5.177,4.823 6.177,5.385 1,0.563 10 false Park/Neutral Position Switch Assembly 4.802,4.531 4.958,4.729 0.156,0.198 10 false 4 4.573,5.354 4.729,5.552 0.156,0.198 10 false 5 1.604,5.115 1.917,5.313 0.313,0.198 10 false ST 0.542,5.646 1.615,5.844 1.073,0.198 10 false 250A FL 3.531,5.823 3.688,6.021 0.156,0.198 10 false 5 2.771,5.813 2.927,6.01 0.156,0.198 10 false 3 2.781,6.229 2.938,6.427 0.156,0.198 10 false 1 3.542,6.25 3.698,6.448 0.156,0.198 10 false 2 3.125,6.698 3.438,6.896 0.313,0.198 10 false ST 6.125,6.365 6.583,6.563 0.458,0.198 10 false G56 6.177,6.146 6.49,6.344 0.313,0.198 10 false 28 6.469,6.354 6.927,6.552 0.458,0.198 10 false STA 6.521,7.438 6.979,7.635 0.458,0.198 10 false ECM 1.729,6.354 2.188,6.552 0.458,0.198 10 false D12 1.031,6.625 1.344,6.823 0.313,0.198 10 false D1 1.083,6.438 1.24,6.635 0.156,0.198 10 false 1 1.552,6.344 1.708,6.542 0.156,0.198 10 false 1 1.469,7.438 2.542,7.635 1.073,0.198 10 false Starter 0.677,8.083 1.75,8.281 1.073,0.198 10 false Battery


for Manual Transmission
A413215E01
0.938,0.844 1.25,1.042 0.313,0.198 10 false NE 0.75,1.521 1.365,1.719 0.615,0.198 10 false STAR 0.854,3.115 1.313,3.313 0.458,0.198 10 false STA 0.323,3.958 0.938,4.156 0.615,0.198 10 false G213 0.333,4.125 1.865,4.5 1.531,0.375 10 false Certification ECU (Smart Key ECU Assembly) 1.25,0.729 1.5,0.927 0.25,0.198 10 false 14 1.25,1.427 1.563,1.625 0.313,0.198 10 false 10 1.271,3.01 1.583,3.208 0.313,0.198 10 false 12 6.125,0.854 6.583,1.052 0.458,0.198 10 false C35 6.198,0.646 6.51,0.844 0.313,0.198 10 false 29 6.469,0.844 6.927,1.042 0.458,0.198 10 false NEO 4.802,3.563 5.26,3.76 0.458,0.198 10 false A40 4.479,3.448 4.635,3.646 0.156,0.198 10 false 2 4.469,4.115 4.625,4.313 0.156,0.198 10 false 1 4.792,3.75 6.063,4.125 1.271,0.375 10 false Clutch Pedal Switch Assembly 6.115,6.365 6.573,6.563 0.458,0.198 10 false G56 6.219,6.156 6.531,6.354 0.313,0.198 10 false 10 6.469,6.365 6.927,6.563 0.458,0.198 10 false STA 6.552,7.427 7.01,7.625 0.458,0.198 10 false ECM 3.115,6.698 3.427,6.896 0.313,0.198 10 false ST 3.552,5.833 3.708,6.031 0.156,0.198 10 false 5 3.563,6.26 3.719,6.458 0.156,0.198 10 false 2 2.76,5.823 2.917,6.021 0.156,0.198 10 false 3 2.76,6.229 2.917,6.427 0.156,0.198 10 false 1 1.667,5.115 1.979,5.313 0.313,0.198 10 false ST 0.563,5.646 1.635,5.844 1.073,0.198 10 false 250A FL 1.729,6.354 2.188,6.552 0.458,0.198 10 false D12 1.552,6.313 1.708,6.51 0.156,0.198 10 false 1 1.031,6.635 1.344,6.833 0.313,0.198 10 false D1 1.125,6.417 1.281,6.615 0.156,0.198 10 false 1 1.677,7.448 2.75,7.646 1.073,0.198 10 false Starter 0.688,8.083 1.76,8.281 1.073,0.198 10 false Battery


CAUTION / NOTICE / HINT

HINT:
·

The following troubleshooting flowchart is based on the premise that the engine is cranked normally.

If the engine will not crank, proceed to the Problem Symptoms Table (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>PROBLEM SYMPTOMS TABLE).

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.


d.

Check the value displayed on the GTS when the engine switch is turned to on (IG) and when the engine is started.

Standard:
Condition Display (Starter Signal)
Engine switch on (IG) OFF
Engine is started ON


Result
Result Proceed to
NG (for Automatic transmission) A
NG (for Manual transmission) B
OK C



A

2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

B

4.INSPECT CLUTCH SWITCH ASSEMBLY

C

2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly (See page Drivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION).

Result
Result Proceed to
NG A
OK B



A

3.REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

B

7.CHECK HARNESS AND CONNECTOR (PNP SWITCH OR CLUTCH SWITCH ASSEMBLY - STA TERMINAL OF ECM)
3.REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Replace the park/neutral position switch assembly (See page Drivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>REMOVAL).



NEXT

6.READ VALUE USING GTS (STARTER SIGNAL)
4.INSPECT CLUTCH SWITCH ASSEMBLY
a.

Check the clutch switch assembly (See page Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION).

Result
Result Proceed to
NG A
OK B



A

5.REPLACE CLUTCH SWITCH ASSEMBLY

B

7.CHECK HARNESS AND CONNECTOR (PNP SWITCH OR CLUTCH SWITCH ASSEMBLY - STA TERMINAL OF ECM)
5.REPLACE CLUTCH SWITCH ASSEMBLY
a.

Replace the clutch switch assembly (See page Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH>REMOVAL).



NEXT

6.READ VALUE USING GTS (STARTER SIGNAL)
6.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.


d.

Check the value displayed on the GTS when the engine switch is turned to on (IG) and when the engine is started.

Standard:
Condition Display (Starter Signal)
Engine switch on (IG) OFF
Engine is started ON


Result
Result Proceed to
NG A
OK B



A

7.CHECK HARNESS AND CONNECTOR (PNP SWITCH OR CLUTCH SWITCH ASSEMBLY - STA TERMINAL OF ECM)

B

SYSTEM OK

7.CHECK HARNESS AND CONNECTOR (PNP SWITCH OR CLUTCH SWITCH ASSEMBLY - STA TERMINAL OF ECM)
a.

for Automatic Transmission:

i.

Disconnect the park/neutral position switch assembly connector.


ii.

Disconnect the ECM connector


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C159-5 - G56-28 (STA) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C159-5 or G56-28 (STA) - Body ground Always 10 kΩ or higher



iv.

Reconnect the park/neutral position switch assembly connector.


v.

Reconnect the ECM connector.



b.

for Manual Transmission:

i.

Disconnect the clutch pedal switch connector.


ii.

Disconnect the ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A40-1 - G56-10 (STA) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A40-1 or G56-10 (STA) - Body ground Always 10 kΩ or higher



iv.

Reconnect the clutch pedal switch connector.


v.

Reconnect the ECM connector.




OK

8.CHECK WHETHER DTC OUTPUT RECURS

NG

REPLACE HARNESS OR CONNECTOR

8.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.



e.

Drive the vehicle at more than 20 km/h (12.4 mph) for more than 20 seconds.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Read the DTCs.

Result
Result Proceed to
P0617 A
No DTC B



A

B

SYSTEM OK