Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM (w/ Multi-display) › from 2017.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261009 TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/ Multi-display) J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/ Multi-display)  Main Switch Circuit  


DESCRIPTION

When the back sonar or clearance sonar switch assembly is turned on, the ON signal is input into the ECU.

WIRING DIAGRAM

E285868E04
2.552,1.323 2.823,1.49 0.271,0.167 10 false IND 4.344,0.865 4.667,1.052 0.323,0.188 10 false ECU 2.552,0.875 2.875,1.063 0.323,0.188 10 false IG 4.76,0.625 4.927,0.813 0.167,0.188 10 false 2 5.76,0.76 6.219,0.948 0.458,0.188 10 false CLSW 0.208,0.792 1.115,1.26 0.906,0.469 10 false from IG NO.1 Relay 1.344,0.646 2.281,0.833 0.938,0.188 10 false ECU-IG NO.2 5.604,1.813 7.052,2.083 1.448,0.271 10 false I9*1, G228*2 5.604,1.979 6.865,2.344 1.26,0.365 10 false Clearance Warning ECU 2.583,1.677 3.01,1.865 0.427,0.188 10 false G198 2.594,1.833 4.625,2.167 2.031,0.333 10 false Back Sonar or Clearance Sonar Switch Assembly 5.458,0.625 5.677,0.813 0.219,0.188 10 false 9 2.354,1.083 2.667,1.375 0.313,0.292 10 false 4 2.365,0.625 2.688,1.125 0.323,0.5 10 false 5 0.115,2.073 1.698,2.344 1.583,0.271 10 false *1: for 4 Sensor Type 0.115,2.365 1.698,2.635 1.583,0.271 10 false *2: for 8 Sensor Type

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the Ignition switch ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body / Clearance Sonar / Data List.


e.

According to the display on the GTS, read the Data List.

Clearance Sonar
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Main Switch Back sonar or clearance sonar switch assembly / OFF or ON OFF: Back sonar or clearance sonar switch assembly off
ON: Back sonar or clearance sonar switch assembly on
-

OK:

The display changes as shown above when the TOYOTA parking assist-sensor system is operated.




OK

NG

2.INSPECT BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY
2.INSPECT BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY
a.

Remove the back sonar or clearance sonar switch assembly (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE SONAR MAIN SWITCH>REMOVAL).


b.

Inspect the back sonar or clearance sonar switch assembly (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE SONAR MAIN SWITCH>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY - CLEARANCE WARNING ECU, BATTERY AND BODY GROUND)

NG

REPLACE BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY - CLEARANCE WARNING ECU, BATTERY AND BODY GROUND)
a.

Disconnect the G198 back sonar or clearance sonar switch assembly connector.


b.

Disconnect the I9*1 or G228*2 clearance warning ECU connector.

*1: for 4 Sensor Type

*2: for 8 Sensor Type



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G198-5 (IG) - Body ground Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 4 Sensor Type
Tester Connection Condition Specified Condition
G198-2 (ECU) - I9-9 (CLSW) Always Below 1 Ω
G198-4 (IND) - Body ground Always Below 1 Ω
G198-2 (ECU) - Body ground Always 10 kΩ or higher


Standard Resistance:
for 8 Sensor Type
Tester Connection Condition Specified Condition
G198-2 (ECU) - G228-9 (CLSW) Always Below 1 Ω
G198-4 (IND) - Body ground Always Below 1 Ω
G198-2 (ECU) - Body ground Always 10 kΩ or higher


Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR