Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM (w/ Multi-display) › from 2017.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261009 TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/ Multi-display) J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/ Multi-display)  Clearance Warning Buzzer Circuit  


DESCRIPTION

The No. 1 clearance warning buzzer is an ECU-operated buzzer that sounds when it receives a pulsed digital signal from the ECU. The ECU operates the buzzer so that it sounds in a pattern that changes depending on the distance to the obstacle.

WIRING DIAGRAM

E283773E05
5.135,2.885 6.75,3.073 1.615,0.188 10 false Clearance Warning ECU 5.146,2.708 6.208,2.979 1.063,0.271 10 false I9*1, G228*2 5.49,1.969 6.031,2.208 0.542,0.24 10 false BBZ*1 3.448,2.188 3.615,2.365 0.167,0.177 10 false Z+ 2.094,2.177 2.271,2.365 0.177,0.188 10 false Z- 3.75,1.917 3.99,2.104 0.24,0.188 10 false 1 1.885,1.917 2.031,2.104 0.146,0.188 10 false 2 5.24,0.833 5.51,1.021 0.271,0.188 10 false 13 5.24,1.917 5.49,2.104 0.25,0.188 10 false 14 1.833,2.865 3.969,3.063 2.135,0.198 10 false No. 1 Clearance Warning Buzzer 1.833,2.719 2.219,2.896 0.385,0.177 10 false G161 5.49,1.135 5.948,1.365 0.458,0.229 10 false EF*2 0.198,3.094 1.813,3.281 1.615,0.188 10 false *1: for 4 Sensor Type 0.198,3.385 1.813,3.573 1.615,0.188 10 false *2: for 8 Sensor Type 5.5,0.938 5.958,1.167 0.458,0.229 10 false ER*1 5.479,2.198 6.021,2.438 0.542,0.24 10 false CBZ*2

PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the Ignition switch ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body / Clearance Sonar / Active Test.


e.

Check that the buzzer operates by performing the Active Test.

Clearance Sonar
Tester Display Test Part Control Range Diagnostic Note
Buzzer No. 1 clearance warning buzzer/ Operate or Stop Operate: No. 1 clearance warning buzzer ON
Stop: No. 1 clearance warning buzzer OFF
Confirm that the vehicle is stopped and the ignition switch is ON

OK:

The No. 1 clearance warning buzzer sounds.




OK

NG

2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU - CLEARANCE WARNING BUZZER)
2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU - CLEARANCE WARNING BUZZER)
a.

Disconnect the I9*1 or G228*2 clearance warning ECU connector.

*1: for 4 Sensor Type

*2: for 8 Sensor Type



b.

Disconnect the G161 No. 1 clearance warning buzzer connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 4 Sensor Type
Tester Connection Condition Specified Condition
I9-14 (BBZ) - G161-1 (Z+) Always Below 1 Ω
I9-13 (ER) - G161-2 (Z-) Always Below 1 Ω
I9-14 (BBZ) - Body ground Always 10 kΩ or higher
I9-13 (ER) - Body ground Always 10 kΩ or higher

for 8 Sensor Type
Tester Connection Condition Specified Condition
G228-14 (CBZ) - G161-1 (Z+) Always Below 1 Ω
G228-13 (EF) - G161-2 (Z-) Always Below 1 Ω
G228-14 (CBZ) - Body ground Always 10 kΩ or higher
G228-13 (EF) - Body ground Always 10 kΩ or higher




OK

3.REPLACE NO. 1 CLEARANCE WARNING BUZZER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE NO. 1 CLEARANCE WARNING BUZZER
a.

Replace the No. 1 clearance warning buzzer with a new or normally functioning one (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE WARNING BUZZER>REMOVAL).



NEXT

4.PERFORM ACTIVE TEST USING GTS
4.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the Ignition switch ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Clearance Sonar / Active Test.


e.

Check that the buzzer operates by performing the Active Test.

Clearance Sonar
Tester Display Test Part Control Range Diagnostic Note
Buzzer No. 1 clearance warning buzzer/ Operate or Stop Operate: No.1 clearance warning buzzer ON
Stop: No. 1 clearance warning buzzer OFF
Confirm that the vehicle is stopped and the ignition switch is ON

OK:

The No. 1 clearance warning buzzer sounds.


Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

END (NO. 1 CLEARANCE WARNING BUZZER WAS DEFECTIVE)

B

C