Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2017.08
RM27T0E _58 Vehicle Interior _053733 METER / GAUGE / DISPLAY _0261082 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Meter Illumination is Always Dark  


DESCRIPTION

This inspection is only for vehicles with automatic light control.

The meter CPU receives signals from this circuit to adjust the illumination of the meter. The meter CPU sets the illumination level based on the user operation of the light control rheostat.

HINT:
·

The meter illumination level can be adjusted by the light control rheostat.

·

The meter illumination dims when the light control switch is turned to the tail or head position at night.

·

Setting the meter illumination to maximum brightness cancels the above dimming of the meter illumination.



WIRING DIAGRAM

E200342E04
1.198,1.531 1.573,1.688 0.375,0.156 10 false CLTB 1.198,2.115 1.573,2.292 0.375,0.177 10 false CLTE 1.198,2.667 1.573,2.844 0.375,0.177 10 false CLTS 1.635,1.521 1.823,1.677 0.188,0.156 10 false 19 1.635,2.094 1.823,2.25 0.188,0.156 10 false 21 1.635,2.646 1.823,2.802 0.188,0.156 10 false 20 3.625,1.542 4,1.698 0.375,0.156 10 false CLTB 3.625,2.094 4,2.271 0.375,0.177 10 false CLTE 3.625,2.646 4,2.823 0.375,0.177 10 false CLTS 3.438,1.552 3.542,1.708 0.104,0.156 10 false 1 3.438,2.104 3.542,2.26 0.104,0.156 10 false 2 3.448,2.646 3.552,2.802 0.104,0.156 10 false 4 0.833,3.25 1.365,3.417 0.531,0.167 10 false G217 0.833,3.396 1.854,3.563 1.021,0.167 10 false Main Body ECU 3.573,3.271 4.573,3.583 1,0.313 10 false Automatic Light Control Sensor 3.563,3.104 3.844,3.26 0.281,0.156 10 false H84 5.052,3.26 6.906,3.417 1.854,0.156 10 false Combination Meter Assembly 3.781,0.438 6.292,0.594 2.51,0.156 10 false to each part that uses the dimmer signal 0.563,4.323 2.26,4.479 1.698,0.156 10 false : CAN Communication Line

PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication DTC is output.


ii.

w/o Central Gateway ECU (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).

Result
Result Proceed to
CAN communication DTC is not output. A
CAN communication system DTC is output (w/ Central Gateway ECU) B
CAN communication system DTC is output (w/o Central Gateway ECU) C




A

2.CHECK DTC (LIGHT SENSOR CIRCUIT)

B

C

2.CHECK DTC (LIGHT SENSOR CIRCUIT)
a.

Check if DTC B1244 is output (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for LED Headlight)>DTC CHECK / CLEAR).

Result
Result Proceed to
B1244 is not output. A
B1244 is output. B



A

3.CHECK OPERATION (HEATER CONTROL PANEL)

B

3.CHECK OPERATION (HEATER CONTROL PANEL)
a.

Turn the ignition switch to ON.


b.

Turn the light control switch to the tail, head, or AUTO position.


c.

Cover the automatic light control sensor.


d.

Check the heater control panel illumination.

Result
Result Proceed to
Heater control panel illumination does not operate normally. A
Heater control panel illumination operates normally. B

HINT:

Both the heater control panel illumination and combination meter assembly illumination dim according to the dimmer signal. Therefore, when only the meter illumination is always dark, there may be a malfunction in the combination meter assembly.




A

4.CHECK OPERATION (AUTOMATIC LIGHT CONTROL SYSTEM)

B

REPLACE COMBINATION METER ASSEMBLY

4.CHECK OPERATION (AUTOMATIC LIGHT CONTROL SYSTEM)
a.

Turn the ignition switch to ON.


b.

Turn the light control switch to the AUTO position.


c.

Cover the automatic light control sensor.


d.

Check the taillights and low beam headlights.

OK:

The taillights and low beam headlights come on.



e.

Uncover the automatic light control sensor.


f.

Check the low beam headlights and taillights.

OK:

The taillights and low beam headlights go off.


Result
Result Proceed to
Automatic light control system operates normally. A
Automatic light control system does not operate normally. B



A

5.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

5.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Replace the main body ECU (multiplex network body ECU) with a new or a normal one (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).

OK:

The operation of the combination meter assembly returns to normal.


HINT:

The meter CPU controls the meter illumination based on an auto dimmer signal from the main body ECU (multiplex network body ECU). When the meter illumination is always dark (very dim), it may be due to the main body ECU (multiplex network body ECU) sending an auto dimmer signal to the meter CPU because of a malfunction in the main body ECU (multiplex network body ECU).




OK

END (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])

NG

REPLACE COMBINATION METER ASSEMBLY