These DTCs indicate that the DC motor of the turbocharger is malfunctioning. The ECM monitors the DC motor current to detect an open or short in the DC motor circuit. If the current meets certain criteria, the ECM stores a DTC and illuminates the MIL immediately.
The DC motor is used to operate the nozzle vane of the turbocharger. The nozzle vane opens and closes to change the velocity of exhaust emissions in order to control the turbo pressure. The ECM varies the duty ratio of the DC motor in accordance with the driving conditions.
If the nozzle vane is stuck closed (DC motor stuck off), drivability may deteriorate at wide open throttle. If the nozzle vane is stuck open (DC motor stuck on), drivability may deteriorate at intermediate throttle positions or the engine power may be insufficient.
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Maintain the Active Test "Activate the VN Turbo Open" at Open (VN turbo fully open) and OFF (normal control) for 65 seconds or more. | The difference between the target VN opening angle and the actual VN opening angle is 50% or greater for 65 seconds or more.
(1 trip detection logic) |
·
Turbocharger nozzle vane control actuator ·
Turbocharger sub-assembly ·
Turbocharger nozzle vane is stuck or movement is irregular |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| 2 seconds after engine is started, race engine for 1 second | The DC motor duty ratio is 80% or more and the motor current is 0.5 A or less for 3 seconds or more (1 trip detection logic). | ·
Open in DC motor (turbocharger nozzle vane control actuator) circuit ·
Turbocharger nozzle vane control actuator ·
Turbocharger nozzle vane is stuck or movement is irregular |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| 2 seconds after engine is started, race engine for 1 second | Overcurrent is detected 25 times or more (0.4 seconds or more) (1 trip detection logic). | ·
Short in DC motor (turbocharger nozzle vane control actuator) circuit ·
Turbocharger nozzle vane control actuator ·
Turbocharger nozzle vane is stuck or movement is irregular |
If DTC P0046, P0047 and/or P0048 is stored due to the nozzle vane being stuck closed, the following symptom may appear:
Vehicle surge when driving with full load
If DTC P0046, P0047 and/or P0048 is stored due to the nozzle vane being stuck open, the following symptoms may appear:
Lack of power
Vehicle surge or hesitation under light or medium load
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0046 is output | A |
| DTC P0047 and/or P0048 is output | B |
| DTC P0046, P0047 and/or P0048 and other DTCs are output | C |
If codes other than DTC P0046, P0047 and/or P0048 are output, perform troubleshooting for those DTCs first.
A
B
C
Remove the turbocharger sub-assembly (See page Engine / Hybrid System>1GD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER>REMOVAL).
Inspect the turbocharger nozzle vane plate.
Remove the e-washer from the turbocharger nozzle vane control actuator.
Move the turbocharger vane control rod subassembly and check that the turbocharger nozzle vane plate moves.
| Result | Proceed to |
|---|---|
| Catches, but operates* | OK |
| Gets stuck and does not operate | NG |
*: Check several times.
OK
NG
Replace the turbocharger nozzle vane control actuator (See page Engine / Hybrid System>1GD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER>DISASSEMBLY).
NEXT
Replace the turbocharger sub-assembly (See page Engine / Hybrid System>1GD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER>REMOVAL).
NEXT
Disconnect the DC motor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (M-) - 2 (M+) | Always | 1 to 100 Ω |
| *a | Component without harness connected
(DC Motor) |
Reconnect the DC motor connector.
OK
NG
Disconnect the DC motor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C141-1 (M-) - C151-2 (VNM-) | Always | Below 1 Ω |
| C141-2 (M+) - C151-1 (VNM+) | Always | Below 1 Ω |
| C141-1 (M-) or C151-2 (VNM-) - Body ground and other terminals | Always | 10 kΩ or higher |
| C141-2 (M+) or C151-1 (VNM+) - Body ground and other terminals | Always | 10 kΩ or higher |
Reconnect the DC motor connector.
Reconnect the ECM connector.
OK
NG
Replace the ECM (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL).
NEXT
Replace the turbocharger nozzle vane control actuator (See page Engine / Hybrid System>1GD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER>DISASSEMBLY).
NEXT
Repair or replace the harness or connector.
NEXT
Connect the GTS to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off and wait for 30 seconds or more.
Turn the engine switch on (IG) and turn the GTS on.
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VN Turbo Open.
Maintain the Active Test "Activate the VN Turbo Open" at Open (VN turbo fully open) and OFF (normal control) for 65 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
NEXT