Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260475 ECD SYSTEM C

1GD-FTV ENGINE CONTROL  ECD SYSTEM  P0191  Fuel Rail Pressure Sensor Circuit Range / Performance  


DESCRIPTION

HINT:

Refer to DTC P0087 (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>P0087).


P0191
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Idling for 1 second or more The difference between the main and sub voltage outputs of the fuel pressure sensor is 0.04 V or less, or 1.06 V or higher for 1 second or more (1 trip detection logic).
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor (common rail assembly)

·

ECM



Related Data List
DTC No. Data List
P0191
·

Common Rail Pressure

·

Target Common Rail Pressure



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (COMMON RAIL PRESSURE AND TARGET COMMON RAIL PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Common Rail Pressure and Target Common Rail Pressure.


d.

Start the engine.


e.

Check the change in the values for the data list items above when increasing the engine speed from idling to 3000 rpm with no load.

Result
Result Proceed to
Common Rail Pressure is always 10000 kPa or less
or
Common Rail Pressure is always 200000 kPa or higher
A
Except above B

HINT:

Normally, "Common Rail Pressure" is within 5000 kPa of "Target Common Rail Pressure".




A

2.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)

B

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0191)
2.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)
a.

Disconnect the fuel pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
r8-5 (PR) - C151-18 (PCR1) Always Below 1 Ω
r8-2 (PR2) - C152-26 (PCR2) Always Below 1 Ω
r8-1 (VCS) - C152-33 (VCS) Always Below 1 Ω
r8-6 (VC) - C151-28 (VCM) Always Below 1 Ω
r8-4 (E2) - C151-19 (E2M) Always Below 1 Ω
r8-3 (E2S) - C152-25 (E2S) Always Below 1 Ω
r8-5 (PR) or C151-18 (PCR1) - Body ground and other terminals Always 10 kΩ or higher
r8-2 (PR2) or C152-26 (PCR2) - Body ground and other terminals Always 10 kΩ or higher
r8-1 (VCS) or C152-33 (VCS) - Body ground and other terminals Always 10 kΩ or higher
r8-6 (VC) or C151-28 (VCM) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the fuel pressure sensor connector.


e.

Reconnect the ECM connector.



OK

5.REPLACE COMMON RAIL ASSEMBLY

NG

3.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0191)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0191)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.



d.

Let the engine idle for 1 second.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


f.

Read the DTCs.

Result
Result Proceed to
DTC P0191 is output A
No DTC is output B



A

5.REPLACE COMMON RAIL ASSEMBLY

B

END

5.REPLACE COMMON RAIL ASSEMBLY
a.

Replace the common rail assembly (See page Engine / Hybrid System>1GD-FTV (FUEL)>COMMON RAIL>REMOVAL).



NEXT

6.BLEED AIR FROM FUEL SYSTEM
6.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION).



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0191)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0191)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.



d.

Let the engine idle for 1 second or more.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


f.

Read the DTCs.

Result
Result Proceed to
DTC P0191 is output A
No DTC is output B



A

8.REPLACE ECM

B

END

8.REPLACE ECM

NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.



d.

Let the engine idle for 1 second or more.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


f.

Confirm that the DTC is not output again.



NEXT

END