Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P0201  Injector Circuit / Open - (Cylinder 1)  P0202  Injector Circuit / Open - (Cylinder 2)  P0203  Injector Circuit / Open - (Cylinder 3)  P0204  Injector Circuit / Open - (Cylinder 4)  P062D  No. 1 Fuel Injector Driver Circuit Performance  


DESCRIPTION

The injector assemblies are installed in the cylinder head and inject fuel into the cylinders based on the signals from the ECM.

P0201, P0202, P0203, P0204
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Idling for 5 seconds or more Open or short in injector circuit occurs a certain number of times (a maximum of approx. 0.5 seconds).
(1 trip detection logic)
·

Open or short in injector assembly circuit

·

Injector assembly

·

ECM



P062D
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Idling for 5 seconds or more ECM internal error
(1 trip detection logic)
ECM

WIRING DIAGRAM

A351116E02
5.625,0.385 6.052,0.552 0.427,0.167 10 false #1D+ 5.635,0.802 6.073,0.969 0.438,0.167 10 false #1D- 5.625,2.667 6.104,2.833 0.479,0.167 10 false #3D+ 5.635,1.938 6.115,2.104 0.479,0.167 10 false #2D- 5.625,1.5 6.094,1.667 0.469,0.167 10 false #2D+ 5.208,0.417 5.604,0.573 0.396,0.156 10 false C149 5.344,0.198 5.531,0.354 0.188,0.156 10 false 6 5.198,0.833 5.625,0.99 0.427,0.156 10 false C149 5.344,0.604 5.542,0.76 0.198,0.156 10 false 7 5.208,1.542 5.615,1.698 0.406,0.156 10 false C149 5.333,1.323 5.552,1.479 0.219,0.156 10 false 1 5.208,1.958 5.698,2.115 0.49,0.156 10 false C149 5.344,1.75 5.563,1.906 0.219,0.156 10 false 2 5.208,2.688 5.625,2.844 0.417,0.156 10 false C150 5.333,2.458 5.531,2.615 0.198,0.156 10 false 7 2.854,0.917 2.969,1.073 0.115,0.156 10 false 2 1.792,0.906 1.906,1.063 0.115,0.156 10 false 1 1.635,1.083 2.302,1.26 0.667,0.177 10 false C115 1.635,1.229 3.208,1.396 1.573,0.167 10 false No. 1 Injector Assembly 1.604,2.229 2.24,2.406 0.635,0.177 10 false C116 1.625,4.75 3.198,4.917 1.573,0.167 10 false No. 4 Injector Assembly 1.667,3.396 2.271,3.573 0.604,0.177 10 false C117 1.604,2.375 3.167,2.542 1.563,0.167 10 false No. 2 Injector Assembly 1.625,4.583 2.208,4.76 0.583,0.177 10 false C118 1.667,3.542 3.292,3.708 1.625,0.167 10 false No. 3 Injector Assembly 2.865,2.042 2.979,2.198 0.115,0.156 10 false 2 1.802,2.042 1.917,2.198 0.115,0.156 10 false 1 2.865,3.208 2.979,3.365 0.115,0.156 10 false 2 1.802,3.198 1.917,3.354 0.115,0.156 10 false 1 2.865,4.344 2.979,4.5 0.115,0.156 10 false 2 1.781,4.344 1.896,4.5 0.115,0.156 10 false 1 5.865,4.969 6.198,5.135 0.333,0.167 10 false ECM 5.646,4.229 6.073,4.396 0.427,0.167 10 false #4D- 5.625,3.802 6.146,3.969 0.521,0.167 10 false #4D+ 5.635,3.083 6.073,3.25 0.438,0.167 10 false #3D- 5.208,3.104 5.625,3.26 0.417,0.156 10 false C150 5.323,2.896 5.542,3.052 0.219,0.156 10 false 6 5.198,3.823 5.573,3.979 0.375,0.156 10 false C149 5.333,3.604 5.552,3.76 0.219,0.156 10 false 5 5.208,4.26 5.604,4.417 0.396,0.156 10 false C149 5.323,4.052 5.521,4.208 0.198,0.156 10 false 4

A413239E03
2.479,3.563 4.146,3.844 1.667,0.281 10 false No.1 Integration Relay 2.74,3.135 3.802,3.385 1.063,0.25 10 false EFI-MAIN NO. 1 1.573,2.521 2.635,2.771 1.063,0.25 10 false EFI-MAIN NO. 1 1.875,0.656 2.323,0.927 0.448,0.271 10 false EDU 3,1.177 3.448,1.448 0.448,0.271 10 false EDU 3.771,1.958 4.417,2.302 0.646,0.344 10 false EFI-MAIN NO. 3 4.635,0.479 4.927,0.646 0.292,0.167 10 false 1U 4.698,0.302 4.99,0.469 0.292,0.167 10 false 2 1.208,1.656 1.5,1.823 0.292,0.167 10 false 1U 1.25,2.177 1.542,2.344 0.292,0.167 10 false 1 1.177,2.813 1.469,2.979 0.292,0.167 10 false 1W 1.25,2.646 1.542,2.813 0.292,0.167 10 false 4 4.625,2.802 4.917,2.969 0.292,0.167 10 false 1W 4.708,2.615 5,2.781 0.292,0.167 10 false 8 4.615,2.365 4.906,2.531 0.292,0.167 10 false 1W 4.656,2.177 4.948,2.344 0.292,0.167 10 false 10 5.729,0.469 6.271,0.635 0.542,0.167 10 false C151 5.74,0.979 6.281,1.146 0.542,0.167 10 false C151 5.729,1.594 6.271,1.76 0.542,0.167 10 false G185 5.729,1.99 6.271,2.156 0.542,0.167 10 false G185 5.729,2.375 6.271,2.542 0.542,0.167 10 false G185 5.854,1.396 6.146,1.563 0.292,0.167 10 false 2 5.844,1.792 6.135,1.958 0.292,0.167 10 false 3 5.865,2.177 6.156,2.344 0.292,0.167 10 false 4 5.813,2.594 6.104,2.76 0.292,0.167 10 false 14 5.729,2.802 6.271,2.969 0.542,0.167 10 false G184 6.167,0.969 6.781,1.167 0.615,0.198 10 false +BD2 6.146,0.448 6.76,0.646 0.615,0.198 10 false +BD1 6.156,1.594 6.771,1.792 0.615,0.198 10 false +B 6.167,1.979 6.781,2.177 0.615,0.198 10 false +B2 6.167,2.365 6.781,2.563 0.615,0.198 10 false +B3 6.146,2.792 6.76,2.99 0.615,0.198 10 false MREL 6.323,4.74 6.938,4.938 0.615,0.198 10 false ECM 0.688,4.99 1.302,5.188 0.615,0.198 10 false Battery 0.531,4.021 1.146,4.219 0.615,0.198 10 false 70A FL 5.854,0.75 6.146,0.917 0.292,0.167 10 false 4 5.854,0.208 6.146,0.375 0.292,0.167 10 false 5 4.615,1.813 4.906,1.979 0.292,0.167 10 false 1W 4.698,1.281 4.99,1.448 0.292,0.167 10 false 3 4.635,1.5 4.927,1.667 0.292,0.167 10 false 1U 4.677,1.656 4.969,1.823 0.292,0.167 10 false 1 1.208,2.365 1.5,2.531 0.292,0.167 10 false 1S 1.25,1.448 1.542,1.615 0.292,0.167 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Result:
Result Proceed to
DTC P0201, P0202, P0203 or P0204 is output A
DTC P062D is output B




B

2.INSPECT ECM (+BD1, +BD2 VOLTAGE)

A

7.CHECK WHETHER DTC OUTPUT RECURS
2.INSPECT ECM (+BD1, +BD2 VOLTAGE)
a.
U169392E01
1.417,1.51 1.115,2.396 false 1.479,1.51 2.26,2.396 false 2.146,1.51 2.938,2.396 false 1.313,0.938 1.698,1.094 0.385,0.156 10 false C151 1.854,2.427 2.458,2.583 0.604,0.156 10 false 4 (+BD2) 0.104,0.094 0.375,0.25 0.271,0.156 10 false *a 0.74,2.427 1.448,2.583 0.708,0.156 10 false 5 (+BD1) 1.823,0.948 2.219,1.104 0.396,0.156 10 false C152 2.771,2.427 3.219,2.583 0.448,0.156 10 false 1 (E1)

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C151-5 (+BD1) - C152-1 (E1) Engine switch on (IG) 11 to 14 V
C151-4 (+BD2) - C152-1 (E1) Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Component with harness connected
(ECD)



OK

3.REPLACE ECM

NG

4.INSPECT NO. 1 INTEGRATION RELAY (EDU)
3.REPLACE ECM

NEXT

16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.INSPECT NO. 1 INTEGRATION RELAY (EDU)

OK

5.REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

6.REPLACE NO. 1 INTEGRATION RELAY
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPLACE NO. 1 INTEGRATION RELAY
a.

Replace the No. 1 integration relay.



NEXT

16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.



d.

Turn the engine switch off for 30 seconds.


e.

Start the engine and idle it for 30 seconds.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Check the DTCs output on the GTS.

HINT:
·

The cylinder with the malfunctioning injector assembly can be determined based on the output DTCs.

·

If the DTC P0201 is output, check the No. 1 injector assembly circuit.

·

If the DTC P0202 is output, check the No. 2 injector assembly circuit.

·

If the DTC P0203 is output, check the No. 3 injector assembly circuit.

·

If the DTC P0204 is output, check the No. 4 injector assembly circuit.





NEXT

8.INSPECT ECM (INJECTION SIGNAL)
8.INSPECT ECM (INJECTION SIGNAL)
a.

Disconnect the injector assembly connectors for all cylinders.

NOTICE:

If only the injector assembly connector of the malfunctioning cylinder is disconnected, the engine will start and there will be rough idling. Therefore, disconnect all injector assembly connectors before inspecting the waveform.



b.

Start the engine.


c.

Check the waveform of the injector assembly connectors using an oscilloscope.

U169491E01
1.573,2.073 2.406,2.25 0.833,0.177 10 false 1 msec./DIV. 3.5,0.396 4.146,0.573 0.646,0.177 10 false 10 V/DIV. 3.635,1.635 4,1.813 0.365,0.177 10 false GND 4.604,0.604 5,0.76 0.396,0.156 10 false C115 5.448,0.052 5.646,0.229 0.198,0.177 10 false *a 4.854,0.417 5.052,0.594 0.198,0.177 10 false *b 6.396,0.417 6.594,0.594 0.198,0.177 10 false *e 5.896,0.417 6.094,0.594 0.198,0.177 10 false *d 5.375,0.417 5.573,0.594 0.198,0.177 10 false *c 5.083,0.604 5.479,0.76 0.396,0.156 10 false C116 5.635,0.604 6.031,0.76 0.396,0.156 10 false C117 6.156,0.604 6.552,0.76 0.396,0.156 10 false C118

Text in Illustration
*a Front view of wire harness connector
(Injector Assembly)
*b No. 1 injector assembly connector
*c No. 2 injector assembly connector *d No. 3 injector assembly connector
*e No. 4 injector assembly connector - -

OK:
Tester Connection Condition Specified Condition
C115-1 - C115-2 Cranking Correct waveform is as shown
C116-1 - C116-2 Cranking Correct waveform is as shown
C117-1 - C117-2 Cranking Correct waveform is as shown
C118-1 - C118-2 Cranking Correct waveform is as shown



d.

Reconnect the injector assembly connectors for all cylinders.



OK

9.INSPECT INJECTOR ASSEMBLY (RESISTANCE)

NG

13.INSPECT ECM (INJECTION SIGNAL)
9.INSPECT INJECTOR ASSEMBLY (RESISTANCE)
a.

Inspect the injector assembly of the cylinder relevant to the DTC (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL INJECTOR>INSPECTION).



NG

10.REPLACE INJECTOR ASSEMBLY (RELEVANT CYLINDER)

OK

10.REPLACE INJECTOR ASSEMBLY (RELEVANT CYLINDER)
a.

Replace the injector assembly of the cylinder relevant to the DTC (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL INJECTOR>REMOVAL).

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new No. 1 injection pipe sub-assembly and a new No. 2 injection pipe sub-assembly.

·

Follow the procedure in the repair manual and temporarily install the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 1 nozzle leakage pipe assembly pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.





NEXT

11.BLEED AIR FROM FUEL SYSTEM
11.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION).



NEXT

12.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
12.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING

b.

Perform the fuel injector pilot quantity learning (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION ).



NEXT

16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.INSPECT ECM (INJECTION SIGNAL)
a.

Disconnect the injector assembly connectors for all cylinders.

NOTICE:

If only the injector assembly connector of the malfunctioning cylinder is disconnected, the engine will start and there will be rough idling. Therefore, disconnect all injector assembly connectors before inspecting the waveform.



b.

Start the engine.


c.

Check the waveform of the injector assembly connectors using an oscilloscope.

U169466E01
4.188,1.313 3.531,2.188 false 4.25,1.313 4.042,2.198 false 4.313,1.323 4.438,2.479 false 4.365,1.323 5.052,2.49 false 4.479,1.323 5.521,2.292 false 4.531,1.323 6.198,2.292 false 4.667,1.323 6.042,1.979 false 4.729,1.313 5.458,0.802 false 4.24,0.74 4.729,0.896 0.49,0.156 10 false C149 1.438,2.104 2.313,2.271 0.875,0.167 10 false 1 msec./DIV. 3.51,1.646 3.885,1.813 0.375,0.167 10 false GND 3.375,0.438 4.031,0.604 0.656,0.167 10 false 10 V/DIV. 3.188,2.26 3.75,2.427 0.563,0.167 10 false 7 (#1D-) 3.781,2.26 4.365,2.427 0.583,0.167 10 false 6 (#1D+) 4.885,2.531 5.469,2.698 0.583,0.167 10 false 4 (#4D-) 5.5,0.729 6.083,0.896 0.583,0.167 10 false 6 (#3D-) 6.083,2.323 6.667,2.49 0.583,0.167 10 false 1 (#2D+) 6.135,1.938 6.719,2.104 0.583,0.167 10 false 7 (#3D+) 5.417,2.323 6,2.49 0.583,0.167 10 false 2 (#2D-) 4.167,2.531 4.75,2.698 0.583,0.167 10 false 5 (#4D+) 4.042,0.052 4.333,0.25 0.292,0.198 10 false *a 4.708,0.75 5.198,0.906 0.49,0.156 10 false C150

Text in Illustration
*a Component with harness connected
(ECM)
- -

OK:
Tester Connection Condition Specified Condition
C149-6 (#1D+) - C149-7 (#1D-) Cranking Correct waveform is as shown
C149-1 (#2D+) - C149-2 (#2D-) Cranking Correct waveform is as shown
C150-7 (#3D+) - C150-6 (#3D-) Cranking Correct waveform is as shown
C149-5 (#4D+) - C149-4 (#4D-) Cranking Correct waveform is as shown



d.

Reconnect the injector assembly connectors for all cylinders.



NG

14.REPLACE ECM

OK

15.REPAIR OR REPLACE HARNESS OR CONNECTOR
14.REPLACE ECM

NEXT

15.REPAIR OR REPLACE HARNESS OR CONNECTOR
15.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch off for 30 seconds or more.


d.

Start the engine and idle it for 10 seconds.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


f.

Confirm that the DTC is not output again.



NEXT

END