Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P0337  Crankshaft Position Sensor "A" Circuit Low Input  P0338  Crankshaft Position Sensor "A" Circuit High Input  


DESCRIPTION

Refer to DTC P0335 (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>P0335).

P0337
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) for 4 seconds or more Output voltage of crankshaft position sensor is less than 0.3 V for 4 seconds.
(1 trip detection logic)
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

ECM



P0338
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) for 4 seconds or more Output voltage of crankshaft position sensor is higher than 4.7 V for 4 seconds.
(1 trip detection logic)
·

Crankshaft position sensor

·

Crankshaft (crank angle sensor plate)

·

ECM



HINT:
·

If DTC P0337 or P0338 is stored, the following symptoms may appear:

-

Difficulty starting

-

Misfire

-

Combustion noise

-

Black smoke

-

White smoke

-

Lack of power



·
A340471E03
0.021,0.813 0.25,0.979 0.229,0.167 10 false G2 3,1.021 3.344,1.188 0.344,0.167 10 false GND 1.052,1.865 2.021,2.031 0.969,0.167 10 false 20 msec./DIV. 2.615,0.156 3.177,0.323 0.563,0.167 10 false 2 V/DIV. 3,1.542 3.344,1.708 0.344,0.167 10 false GND 0.021,1.344 0.25,1.51 0.229,0.167 10 false NE

Reference: Inspection using an oscilloscope.

The correct waveform is as shown.

ECM Terminal Name Between G2+ and G2-
Between NE+ and NE-
Tester Range 2 V/DIV., 20 msec./DIV.
Condition Idling with warm engine



MONITOR DESCRIPTION

When the sensor output voltage remains at less than 0.3 V, or higher than 4.7 V, the ECM stores a DTC.

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.



e.

Turn the engine switch off for 30 seconds or more.


f.

Disconnect the crankshaft position sensor connector.


g.

Turn the engine switch on (IG) for 4 seconds or more.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


Result:
Result Proceed to
DTC does not change A
DTC changes B



A

2.CHECK ECM (CRANKSHAFT POSITION SENSOR VOLTAGE)

B

5.REPLACE CRANKSHAFT POSITION SENSOR
2.CHECK ECM (CRANKSHAFT POSITION SENSOR VOLTAGE)
a.
U169404E01
2.031,1.635 1.604,2.406 false 2.073,1.646 2.75,2.417 false 1.844,0.917 2.25,1.073 0.406,0.156 10 false C152 2.458,2.427 3.167,2.583 0.708,0.156 10 false 19 (NE-) 0.104,0.094 0.375,0.25 0.271,0.156 10 false *a 1.24,2.427 1.948,2.583 0.708,0.156 10 false 20 (VCNE)

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C152-20 (VCNE) - C152-19 (NE-) Engine switch on (IG) 4.5 to 5.5 V


Text in Illustration
*a Component with harness connected
(ECM)



OK

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

7.REPLACE ECM
3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the crankshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
r7-1 (NE+) - C152-28 (NE+) Always Below 1 Ω
r7-2 (NE-) - C152-19 (NE-) Always Below 1 Ω
r7-1 (NE+) or C152-28 (NE+) - Body ground and other terminals Always 10 kΩ or higher
r7-2 (NE-) or C152-19 (NE-) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the crankshaft position sensor connector.



OK

4.CHECK ECM (CHECK RESISTANCE)

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK ECM (CHECK RESISTANCE)
a.
U169393E01
2.031,1.635 0.719,2.406 false 2.073,1.635 1.792,2.406 false 2.115,1.688 2.656,2.406 false 1.833,0.927 2.333,1.083 0.5,0.156 10 false C152 1.469,2.427 2.177,2.583 0.708,0.156 10 false 19 (NE-) 0.104,0.094 0.375,0.25 0.271,0.156 10 false *a 0.281,2.427 0.99,2.583 0.708,0.156 10 false 20 (VCNE) 2.49,2.427 3.198,2.583 0.708,0.156 10 false 28 (NE+)

Disconnect the crankshaft position sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C152-20 (VCNE) - C152-28 (NE+) Engine switch off No short or open circuit
C152-28 (NE+) - C152-19 (NE-) Engine switch off No short or open circuit


Text in Illustration
*a Component with harness connected
(ECM)


c.

Reconnect the crankshaft position sensor connector.



OK

5.REPLACE CRANKSHAFT POSITION SENSOR

NG

7.REPLACE ECM
5.REPLACE CRANKSHAFT POSITION SENSOR
a.


NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPLACE ECM

NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.



d.

Turn the engine switch off for 30 seconds or more.


e.

Turn the engine switch on (IG) for 4 seconds or more.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Confirm that the DTC is not output.



NEXT

END