Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  U010E  Lost Communication with Reductant Control Module  


DESCRIPTION

The ECM sends and receives data to and from the urea pump control ECU via local CAN communication.

U010E
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
1.6 seconds or more after turning the engine switch on (IG). Communication stops between the ECM and the urea pump control ECU for 1.6 seconds or more.
(1 trip detectionlogic)
·

Urea pump control ECU

·

Harness or connector

·

ECM



MONITOR DESCRIPTION

The ECM stores a DTC when a communication malfunction occurs between the ECM and urea pump control ECU.

WIRING DIAGRAM

A413417E03
1.5,2.052 3.677,2.323 2.177,0.271 10 false Power Management Control ECU 1.49,1.885 2.104,2.083 0.615,0.198 10 false G213 4.26,1.229 4.875,1.427 0.615,0.198 10 false IG2 3.208,0.688 3.823,0.885 0.615,0.198 10 false IG2 3.083,0.406 3.698,0.604 0.615,0.198 10 false 1 5.438,0.406 6.052,0.604 0.615,0.198 10 false 2 3.438,0.406 4.052,0.604 0.615,0.198 10 false 2 5.073,0.406 5.688,0.604 0.615,0.198 10 false 1 5.198,0.729 5.979,0.927 0.781,0.198 10 false IGN 6.063,0.542 6.677,0.74 0.615,0.198 10 false IGSW 5.833,0.385 6.448,0.583 0.615,0.198 10 false 18 2.281,1.292 2.896,1.49 0.615,0.198 10 false IG1D 2.24,1.031 2.854,1.229 0.615,0.198 10 false 3 2.24,2.75 2.854,2.948 0.615,0.198 10 false DCU-B 2.177,2.458 2.792,2.656 0.615,0.198 10 false 1 2.573,2.458 3.188,2.656 0.615,0.198 10 false 2 4.625,3.313 5.594,3.5 0.969,0.188 10 false DCU NO. 1 4.635,4.083 5.604,4.271 0.969,0.188 10 false DCU NO. 2 0.396,5.583 1.01,5.781 0.615,0.198 10 false 70A FL 2.896,4.656 3.51,4.854 0.615,0.198 10 false DCU 3.844,5.208 4.458,5.406 0.615,0.198 10 false CANU 3.854,5.708 4.469,5.906 0.615,0.198 10 false CAND 3.656,6.146 4.271,6.344 0.615,0.198 10 false G184 3.677,6.333 4.292,6.531 0.615,0.198 10 false ECM 2.385,7.135 6.052,7.333 3.667,0.198 10 false : CAN Communication Line 0.615,6.802 4.281,7 3.667,0.198 10 false Battery 1.198,5.594 1.813,5.792 0.615,0.198 10 false 250A FL 1.719,4.104 2.333,4.302 0.615,0.198 10 false DCU 5.99,7.271 7.156,7.604 1.167,0.333 10 false Urea Pump Control ECU 6.094,4.354 7.063,4.542 0.969,0.188 10 false UREL 6.094,5.208 6.708,5.406 0.615,0.198 10 false CAN+ 6.094,5.708 6.708,5.906 0.615,0.198 10 false CAN- 6.083,3.688 7.052,3.875 0.969,0.188 10 false +BU2 6.083,3.958 7.052,4.146 0.969,0.188 10 false +BU1 6.083,3.438 7.052,3.625 0.969,0.188 10 false +BU3 6.083,3.167 7.052,3.354 0.969,0.188 10 false +BU4 6.094,2.896 7.063,3.083 0.969,0.188 10 false +BU5 6.104,2.594 7.073,2.781 0.969,0.188 10 false BATT 5.833,2.427 6.802,2.615 0.969,0.188 10 false 30 5.875,2.792 6.844,2.979 0.969,0.188 10 false 2 5.875,3.052 6.844,3.24 0.969,0.188 10 false 1 5.844,3.344 6.813,3.531 0.969,0.188 10 false 19 5.844,3.604 6.813,3.792 0.969,0.188 10 false 10 5.844,3.844 6.813,4.031 0.969,0.188 10 false 11 4.729,3.052 5.344,3.25 0.615,0.198 10 false 1 5.094,3.052 5.708,3.25 0.615,0.198 10 false 2 4.719,3.833 5.333,4.031 0.615,0.198 10 false 1 5.094,3.823 5.708,4.021 0.615,0.198 10 false 2 2.594,4.229 3.208,4.427 0.615,0.198 10 false 1 3.354,4.219 3.969,4.417 0.615,0.198 10 false 2 2.583,3.854 3.198,4.052 0.615,0.198 10 false 3 3.344,3.844 3.958,4.042 0.615,0.198 10 false 5 4.344,5.521 4.958,5.719 0.615,0.198 10 false 35 4.344,5.042 4.958,5.24 0.615,0.198 10 false 27 6.104,6.104 6.719,6.302 0.615,0.198 10 false E01 6.104,6.344 6.719,6.542 0.615,0.198 10 false E02 6.104,6.615 6.719,6.813 0.615,0.198 10 false E03 5.896,4.25 6.865,4.438 0.969,0.188 10 false 9 5.833,5.031 6.802,5.219 0.969,0.188 10 false 27 5.844,5.542 6.813,5.729 0.969,0.188 10 false 26 5.833,5.969 6.802,6.156 0.969,0.188 10 false 52 5.833,6.229 6.802,6.417 0.969,0.188 10 false 51 5.854,6.49 6.823,6.677 0.969,0.188 10 false 50 6.01,7.052 6.979,7.24 0.969,0.188 10 false s4

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

According to the display on the GTS, select "Health Check".


d.

Check for currently output system DTCs.

Result:
Result Proceed to
DTC U010E is output A
DTC U010E and other DTCs are output* B


HINT:

*: If any other DTCs are output, perform troubleshooting for those DTCs first.




A

2.CHECK HARNESS AND CONNECTOR (UREA PUMP CONTROL ECU - ECM)

B

2.CHECK HARNESS AND CONNECTOR (UREA PUMP CONTROL ECU - ECM)
a.

Disconnect the urea pump control ECU connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
s4-27 (CAN+) - G184-27 (CANU) Always Below 1 Ω
s4-26 (CAN-) - G184-35 (CAND) Always Below 1 Ω
s4-27 (CAN+) or G184-27 (CANU) - Body ground and other terminals Always 10 kΩ or higher
s4-26 (CAN-) or G184-35 (CAND) - Body ground and other terminals Always 10 kΩ or higher




OK

3.CHECK UREA PUMP CONTROL ECU (BATT TERMINAL)

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

3.CHECK UREA PUMP CONTROL ECU (BATT TERMINAL)
a.
U169118E03
2.458,1.021 2.458,0.396 2.458,0.396 2.583,0.396 false 0.396,1 0.583,1.167 0.188,0.167 10 false s4 0.083,0.01 0.385,0.177 0.302,0.167 10 false *a 2.615,0.313 3.292,0.51 0.677,0.198 10 false 30 (BATT)

Disconnect the urea pump control ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
s4-30 (BATT) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Urea Pump Control ECU)



OK

4.CHECK DCU MAIN RELAY (DCU)

NG

4.CHECK DCU MAIN RELAY (DCU)

OK

5.CHECK UREA PUMP CONTROL ECU (UREL TERMINAL)

NG

REPLACE DCU MAIN RELAY (DCU)

5.CHECK UREA PUMP CONTROL ECU (UREL TERMINAL)
a.
A413700E01
0.188,0.99 0.5,1.188 0.313,0.198 10 false *2 0.115,0.125 0.427,0.323 0.313,0.198 10 false *1

Remove the DCU relay from the engine room relay block.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
DCU relay terminal 2 - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*1 Engine Room Relay Block
*2 DCU Relay



OK

6.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK - UREA PUMP CONTROL ECU)

NG

7.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK - UREA PUMP CONTROL ECU)
6.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK - UREA PUMP CONTROL ECU)
A413701E01
5.104,0.26 5.552,0.5 0.448,0.24 4.615,2.198 4.948,1.167 true 5.073,2.167 5.042,1.177 true 5.583,2.427 5.646,1.177 true 6.344,2.427 5.729,1.229 true 6.042,0.708 5.917,0.708 5.917,0.708 5.719,1.146 true 0.771,0.771 1.083,0.969 0.313,0.198 10 false *1 2.344,0.146 2.656,0.344 0.313,0.198 10 false *2 4.208,0.583 4.521,0.781 0.313,0.198 10 false *a 5.26,0.323 5.573,0.521 0.313,0.198 10 false s4 4.25,2.302 4.896,2.469 0.646,0.167 10 false 1 (+BU4) 5.292,2.49 5.938,2.656 0.646,0.167 10 false 10 (+BU2) 4.896,2.292 5.542,2.458 0.646,0.167 10 false 2 (+BU5) 6.073,2.49 6.719,2.656 0.646,0.167 10 false 19 (+BU3) 6.083,0.635 6.729,0.802 0.646,0.167 10 false 11 (+BU1)

Text in Illustration
*1 DCU Relay *2 Engine Room Relay Block
*a Front view of wire harness connector
(to Urea Pump Control ECU)
- -

a.

Remove the DCU relay from the engine room relay block.


b.

Disconnect the urea pump control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
DCU relay terminal 5 - s4-11 (+BU1) Always Below 1 Ω
DCU relay terminal 5 - s4-10 (+BU2) Always Below 1 Ω
DCU relay terminal 5 - s4-19 (+BU3) Always Below 1 Ω
DCU relay terminal 5 - s4-1 (+BU4) Always Below 1 Ω
DCU relay terminal 5 - s4-2 (+BU5) Always Below 1 Ω
DCU relay terminal 1 - Body ground Always Below 1 Ω
DCU relay terminal 5 or s4-11 (+BU1) - Body ground and other terminals Always 10 kΩ or higher
DCU relay terminal 5 or s4-10 (+BU2) - Body ground and other terminals Always 10 kΩ or higher
DCU relay terminal 5 or s4-19 (+BU3) - Body ground and other terminals Always 10 kΩ or higher
DCU relay terminal 5 or s4-1 (+BU4) - Body ground and other terminals Always 10 kΩ or higher
DCU relay terminal 5 or s4-2 (+BU5) - Body ground and other terminals Always 10 kΩ or higher




OK

REPAIR OR REPLACE HARNESS AND CONNECTOR (DCU RELAY - BATTERY)

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

7.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK - UREA PUMP CONTROL ECU)
A413701E05
5.104,0.26 5.552,0.5 0.448,0.24 5.219,2.208 5.563,1.167 true 0.771,0.771 1.083,0.969 0.313,0.198 10 false *1 2.344,0.146 2.656,0.344 0.313,0.198 10 false *2 4.208,0.583 4.521,0.781 0.313,0.198 10 false *a 5.26,0.323 5.573,0.521 0.313,0.198 10 false s4 5,2.271 5.646,2.438 0.646,0.167 10 false 9 (UREL)

Text in Illustration
*1 DCU Relay *2 Engine Room Relay Block
*a Front view of wire harness connector
(to Urea Pump Control ECU)
- -

a.

Remove the DCU relay from the engine room relay block.


b.

Disconnect the urea pump control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
DCU relay terminal 2- s4-9 (UREL) Always Below 1 Ω
DCU relay terminal 2or s4-9 (UREL) - Body ground and other terminals Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR