Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster) › from 2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260912 VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)  C1425  Open in Stop Light Switch Circuit  


DESCRIPTION

The skid control ECU (brake actuator assembly) detects the brake operating conditions through a signal transmitted by the stop light switch assembly.

DTC Code DTC Detection Condition Trouble Area
C1425 When the IG1 terminal voltage is between 9.5 and 17.4 V, an open STP terminal circuit continues for 3 seconds or more.
·

STP terminal circuit

·

Stop light switch assembly

·

Skid control ECU (Brake actuator assembly)



WIRING DIAGRAM

C386565E01
1.792,3.177 3.625,3.375 1.833,0.198 10 false from Battery 0.823,3.406 1.438,3.604 0.615,0.198 10 false STOP 0.375,2.615 0.531,2.813 0.156,0.198 10 false 1 0.583,2.385 1.354,2.583 0.771,0.198 10 false Diode 0.583,2.177 1.042,2.375 0.458,0.198 10 false A59 0.354,2 0.51,2.198 0.156,0.198 10 false 2 1.417,1.354 1.875,1.552 0.458,0.198 10 false A99 1.427,1.51 3.323,1.854 1.896,0.344 10 false Stop Light Switch Assembly 1.771,0.875 1.927,1.073 0.156,0.198 10 false B 1.563,0.75 1.719,0.948 0.156,0.198 10 false 7 2.219,0.344 2.375,0.542 0.156,0.198 10 false 2 2.063,0.604 2.521,0.802 0.458,0.198 10 false GND 2.375,0.865 2.833,1.063 0.458,0.198 10 false OUT 2.781,0.781 2.938,0.979 0.156,0.198 10 false 1 3.292,2.594 6.5,2.792 3.208,0.198 10 false to Stop Light Circuit 5.75,2.052 6.74,2.427 0.99,0.375 10 false Open Detection Circuit 5.385,0.74 5.542,0.938 0.156,0.198 10 false 2 5.646,0.75 6.104,0.948 0.458,0.198 10 false STP 5.292,2.792 5.604,2.99 0.313,0.198 10 false A6 5.323,3.01 6.927,3.49 1.604,0.479 10 false Skid Control ECU (Brake Actuator Assembly)

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CALIBRATION).


PROCEDURE

1.CHECK STOP LIGHT SWITCH OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed. On
Brake pedal released. Off




OK

2.READ VALUE USING GTS (STOP LIGHT SW)

NG

4.INSPECT STOP LIGHT SWITCH ASSEMBLY
2.READ VALUE USING GTS (STOP LIGHT SW)
a.

Turn the ignition switch off


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch/ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-


f.

Check that the stop light switch display observed on the GTS changes according to the brake pedal operation.

OK:

The GTS displays ON or OFF according to brake pedal operation.




OK

3.RECONFIRM DTC

NG

5.CHECK TERMINAL VOLTAGE (STP)
3.RECONFIRM DTC

b.

Start the engine.


c.

Depress the brake pedal several times to test the stop light circuit.


d.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

B

4.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION).

OK:

The stop light switch assembly is normal.




OK

5.CHECK TERMINAL VOLTAGE (STP)

NG

5.CHECK TERMINAL VOLTAGE (STP)
a.

Make sure that there is no looseness at the locking parts and connecting parts of the connectors.


b.

Disconnect the A6 skid control ECU (brake actuator assembly) connector.


c.
U148258E01
0.07,0.072 0.246,0.263 0.177,0.191 10 *a 0.203,1.026 0.428,1.182 0.224,0.156 10 A6 1.81,0.134 2.293,0.341 0.483,0.207 10 STP 1.31,0.864 1.485,0.218 1.485,0.218 1.751,0.218 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A6-2 (STP) - Body ground Brake pedal depressed 8 to 14 V
Brake pedal released Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))



OK

6.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.RECONFIRM DTC
a.

Reconnect the A6 skid control ECU (brake actuator assembly) connector.



c.

Start the engine.


d.

Drive the vehicle and depress the brake pedal several times to test the stop light circuit.


e.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

B