Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster) › from 2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260912 VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)  TRC OFF Indicator Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via the CAN communication system.

Pressing the VSC OFF switch turns off traction control and pressing and holding this switch turns off traction and VSC controls. If traction control turns off, the TRC OFF indicator light comes on.

WIRING DIAGRAM

C215177E13
5.25,2.031 5.542,2.25 0.292,0.219 10 false A6 5.25,2.219 6.813,2.625 1.563,0.406 10 false Skid Control ECU (Brake Actuator Assembly) 3.208,1.917 4.365,2.146 1.156,0.229 10 false VSC OFF Switch 0.594,2.729 2.615,2.969 2.021,0.24 10 false Combination Meter Assembly 0.667,3.156 2.667,3.365 2,0.208 10 false : CAN Communication System 1.042,1.354 1.708,1.521 0.667,0.167 10 false TRC OFF 1.302,1.854 1.583,2.021 0.281,0.167 10 false IG 0.865,0.698 1.24,1 0.375,0.302 10 false CPU 0.625,2.448 1.052,2.615 0.427,0.167 10 false G304 3.188,1.74 3.708,1.927 0.521,0.188 10 false G226 4.083,1.302 4.271,1.448 0.188,0.146 10 false 5 3.052,1.292 3.177,1.469 0.125,0.177 10 false 2 5.458,1.396 5.854,1.573 0.396,0.177 10 false CSW 5.177,1.271 5.406,1.469 0.229,0.198 10 false 30

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>CALIBRATION).

·

As there may be malfunctions in the transfer system related to when the transfer operates in L4, check the transfer system first (See page Drivetrain>VF4BM (TRANSFER / 4WD / AWD)>TRANSFER SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

2.INSPECT VSC OFF SWITCH

OK

3.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - VSC OFF SWITCH)

NG

3.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - VSC OFF SWITCH)
a.

Disconnect the A6 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the G226 VSC OFF switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A6-30 (CSW) - G226-5 Always Below 1 Ω
A6-30 (CSW) or G226- 5 - Body ground Always 10 kΩ or higher
G226-2 - Body ground Always Below 1 Ω




OK

4.READ VALUE USING GTS (TRC/VSC OFF MODE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING GTS (TRC/VSC OFF MODE)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
TRC/VSC Off Mode TRC/VSC off mode/ Normal, TRC OFF or VSC OFF Normal: Normal mode
TRC OFF: TRC OFF mode
VSC OFF: VSC OFF mode
-


f.

Check that the mode display changes according to VSC OFF switch operation.

OK:

Display changes according to switch operation.




OK

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

NG