Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › from 2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260910 ANTI-LOCK BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  ABS Warning Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

If any of the following is detected, the ABS warning light remains on:

·

The skid control ECU (brake actuator assembly) connector is disconnected from the skid control ECU (brake actuator assembly).

·

There is a malfunction in the skid control ECU (brake actuator assembly) internal circuit.

·

There is an open in the harness between the combination meter assembly and the skid control ECU (brake actuator assembly).

·

The anti-lock brake system is defective.

·

The voltage at terminal IG1 is high.


HINT:

In some cases, the intelligent tester cannot be used when the skid control ECU (brake actuator assembly) is abnormal.


WIRING DIAGRAM

C215178E11
1.052,1.49 1.417,1.656 0.365,0.167 10 false ABS 1.313,1.979 1.594,2.146 0.281,0.167 10 false IG 5.146,2.427 6.698,2.802 1.552,0.375 10 false Skid Control ECU (Brake Actuator Assembly) 5.354,1.844 5.635,2.01 0.281,0.167 10 false IG1 5.365,1.083 5.802,1.26 0.438,0.177 10 false GND1 5.021,1.719 5.219,1.885 0.198,0.167 10 false 34 5.083,0.969 5.229,1.135 0.146,0.167 10 false 1 2.865,1.833 3.875,2.031 1.01,0.198 10 false from IG Circuit 0.542,2.708 2.677,2.927 2.135,0.219 10 false Combination Meter Assembly 0.573,3.292 3.219,3.469 2.646,0.177 10 false : CAN Communication System 0.854,0.677 1.375,0.875 0.521,0.198 10 false CPU 5.146,2.292 5.385,2.448 0.24,0.156 10 false A6 4.104,2.021 5.073,2.188 0.969,0.167 10 false ECU-IG NO. 1 0.542,2.563 0.802,2.708 0.26,0.146 10 false G6

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output (See pagePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).

Result
Result Proceed to
DTC not output A
DTC output B



A

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED

B

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU connector is securely connected.

OK:

The connector is securely connected.




OK

3.CHECK TERMINAL VOLTAGE (IG1)

NG

CONNECT CONNECTOR TO ECU CORRECTLY

3.CHECK TERMINAL VOLTAGE (IG1)

OK

4.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

4.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

OK

5.READ VALUE USING GTS (ABS WARNING LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

5.READ VALUE USING GTS (ABS WARNING LIGHT)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
ABS Warning Light ABS warning light / ON or OFF OFF -

f.

When performing the ABS Warning Light Active Test, check ABS Warning Light in the Data List (See Page ).


ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
ABS Warning Light ABS warning light Warning light ON/OFF Observe the combination meter.

Result
Result Proceed to
Data List Display Data List Display when Performing Active Test ON/OFF Operation
ON Does not change between ON and OFF A
Changes between ON and OFF B
OFF Does not change between ON and OFF A
Changes between ON and OFF B

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DATA LIST / ACTIVE TEST


A

B

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)